Highways Department Tender

Road Markers/Road Stud with Lens Reflector Providing and fixing reflective road studs of ' Category A' Raised pavement markers made out of poly carbonate / methyl methercrylate / ABS moulded body confirming to ASTM D 788 and reflective Panels with micro prismatic lens capable of Providing total internal reflection of the light entering the lens face with retro - reflectance and chrimaticity values conforming to ASTM D4280. The reflective raised pavement markers shall also confirm to the MORTH circular no RW/NH 33023/10/97-DO.III Dt 11.06.97. The height, width and length shall not be less than 15mm, 90mm and 100mm and with minimum reflective area of 13 sq.cm on each side and the slope to the base shall be 35+/- 5 degree. Each reflector shall have a CIL not less than values specified in Table 2 of said MORTH circular . The Strength of detachment o the intergrated cylindrical shanks, (of diameter not less than 19 +/-2mm and height not less than 30 +/- 2mm) from the body is to be a minimum value of 500 kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. The marker shall support a load of 13635 kg tested in accordance with ASTM D4280 and comfirming to IRC 35-2015 guidelines and MORT&H specification 804 etc., complete

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Providing and Fixing of Retro - Reflectorised Cautionary, Mandatory and Informatory signs (with definition board) made out of high intensity Prismatic Grade Sheeting Confirming to Type - IV standards of IRC - 67: 2012 and ASTM D 4959 - 09, specification and fixing over 2mm thicks Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75mmx75mmx6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. the sign post should be painted as per IRC 67 - 2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmx60cm size including cost and conveyance of all materials, equipment, machinery and labour withall leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charges. High intensity Retro - Reflectro Sheet Shall consist of minimum coeffient of Retro - reflection as per Table 6.6 of IRC 67 - 2012. The Retro - Reflection Sheeting shall be covered under 7 years warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67 - 2012. (As per MORTH & H Specification No. 801)

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

1.1 Cautionary Signs-Triangular(Size 900 mm Side)

1.2 Mandatory Signs-Octagon(Size 900 mm Side) (STOP)

1.3 Mandatory Signs-Circle (Size 600 mm)

1.4 Single Chevron Board (Size 800mm*600mm Rectangular)

1.5 Rectangular Size 600 mm * 450 mm

1.6 Rectangular Size (600 mm * 800 mm) For Bus Stop,Bus Bay

Providing and erecting of Retro - Reflectorised Cautionary, Mandatory and Informatory signs (without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 –09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than .10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the round by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer-in-charge. High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro - reflective heeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 . ( as per MoRT&H Specification No.801)

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

2.1 800mm*600mm Rectangular

2.2 900mm Equilateral triangle

2.3 600mm Circular

Providing and erecting of Direction and Place Identification Retro-reflectorised Signs made out of Cube Corner Micro Prismatic Grade Sheeting confirming to Type-XI standards of IRC-67: 2012 and ASTM D 4956 –09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials,equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer-in-charge. Micro Prismatic grade Retro -Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.9 of IRC 67-2012. The retro -reflective sheeting shall be covered under 10 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012. ( as per MoRT&H Specification No.801) (For location of black spot, curve, sharp bend, junction, ghat roads and critical zone applications) (Rate per sqm (for sign having area upto 0.9 sqm) Type XI)

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Direction and Place Identification Signs - Type - IV providing and erecting Direction and place Identification Retro- Reflectorised sign made out of High Intensity Prismatic Grade Sheeting confirming to Type -IV standards of IRC-67:2012 and ASTM D 4956 -09, Specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75x75x6mm with a clear height of not less 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly 45cmx45cmx60cm size including cost and conveyance of all materials equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by consist of minimum coefficient of Retro- reflection as per Table 6.6 of IRC 67-2012. The retro- reflective sheeting shall be converd under 7 year warrantly issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012 (As per MORT&H Specification No.801) Rate per Sqm (For sign having more than 0.9 Sqm)

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

1.1 Rectangular Size (1200mm*900mm) For Place Identification

1.2 Rectangular Size (1200mm*1200mm) For Place Identification

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Providing and Erecting of Retro - reflectorised Hazard Marker Traffic sign made out of high intensity Prismatic Grade sheeting coinfirming to Type - IV standards of IRC -67 : 2012 and ASTM D 4956-09, specification and fixed over 2mm thick aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild steel angle and supported on a mild steel angle post 75x75x6mm and 0.60 m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by meand sof properly designed conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the Engineer in charge. High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro - Reflection as per table 6.6 of IRC 67-2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67: 2012. (as per MORT&H Specification No.801)

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Providing and fixing of Retro Reflectorized Overhead Gantry Informatory signs made of cube corner Micro Prismatic grade sheeting conforming to Type XI standards of IRC67 - 2012 and ASTMD4956 – 09, specification and fixed over 2 mm thick aluminum sheet fixed on back supporting frame mild steel L angle of size 50 mm x 50 mm x 6 mm. The Vertical support post for the installation of overhead sign Gantry shall be made of 300NB (Nominal Bore) MS Pipe with 12mm thick with a ground clearance of 6 meters along with 80 NB (Nominal Bore) MS Pipe with 4 mm thick and 40 NB (Nominal Bore) MS Pipe with 3.2 mm thick support posts. MS Base plate of size 1200mm x 1200mm x 25mm and MS Top plate of size 900mm x 1650mm x 16mm to be used to hold the sign board at the top and bottom respectively. MS Stiffener plates 8mm thick of sizes(420x420), (682x420), (288x288), (288x927), (44x130)are to be used. Anchor bolts of dimension 25mm dia and 1000mm length are to be used as fixtures.The approved direction information should be digitally printed and should have 70% of the co-efficient of Retro-reflection values against the values as mentioned in Table 6.9 of IRC67 – 2012.The Latex printer used for digital printing should use inks with low VOC emissions and have green guard, eco logo certificates as per UL 2801 standards. The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance and a certified copy of three years Outdoor exposure report shall be obtained as per IRC 67-2012 (As per MoRT&H specification No. 801).Cantilever sign shall be installed at the site as per the approved structural and foundation drawing provided in the tender document and including cost and conveyance of all materials, equipment, Machinery and labor with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer-in-charge

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

Providing and fixing of Retro Reflectorized Overhead cantilever Informatory signs made of cube corner Micro Prismatic grade sheeting conforming to Type XI standards of IRC67 - 2012 and ASTMD4956 – 09, specification and fixed over 2 mm thick aluminum sheet fixed on back supporting frame mild steel L angle of size 50 mm x 50 mm x 6 mm. The Vertical support post for the installation of overhead sign Gantry shall be made of 300NB (Nominal Bore) MS Pipe with 12mm thick with a ground clearance of 6 meters along with 80 NB (Nominal Bore) MS Pipe with 4 mm thick and 40 NB (Nominal Bore) MS Pipe with 3.2 mm thick support posts. MS Base plate of size 1200mm x 1200mm x 25mm and MS Top plate of size 900mm x 1650mm x 16mm to be used to hold the sign board at the top and bottom respectively. MS Stiffener plates 8mm thick of sizes(420x420), (682x420), (288x288), (288x927), (44x130)are to be used. Anchor bolts of dimension 25mm dia and 1000mm length are to be used as fixtures.The approved direction information should be digitally printed and should have 70% of the co-efficient of Retro-reflection values against the values as mentioned in Table 6.9 of IRC67 – 2012.The Latex printer used for digital printing should use inks with low VOC emissions and have green guard, eco logo certificates as per UL 2801 standards. The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance and a certified copy of three years Outdoor exposure report shall be obtained as per IRC 67-2012 (As per MoRT&H specification No. 801).Cantilever sign shall be installed at the site as per the approved structural and foundation drawing provided in the tender document and including cost and conveyance of all materials, equipment, Machinery and labor with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer-in-charge

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

Providing and fixing of Rigid Median Marker double side made of tough, high impact resistant, injection-molded , thermoplastic body with an isosceles trapezoidal structure of length , width and height not less than 15cm, 10cm and 10cm respectively and thickness not less than 1.8mm, the body structure shall be rounded at its acute angle, all the corners and edges. The plastic used for moulding the Median Marker shall have a minimum Notched lzod Impact strength value of 600 J/m at room temperature, when tested in accordance with ASTM D256 and shall retain at least 70% of this value when subjected to accelerated weathering for 1000hrs as per ASTM G155 or UL746C. The logo of the manufacturer shall be embossed on either side of body in the injection moulding process. The Median Marker shall have rectangular-shaped, fluorescent yellow color retro-reflective sheeting of size not less than 8.5cm*805cm and with fully reflective micro prismatic cube corners as its retro-reflective elements as per IRC 67-2012 and ASTM D4956-09 type XI specifications reflectivity values. The retro-reflective sheeting shall be both sides of the Median Marker and shall be edge protected with no exposed edges which will prevent edge lifting, vandalism, sheeting damage, ect. The Median Marker shall be fixed by a combination of epoxy adhesive and grouting. Sl No.10

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Road Delineators : Supplying and installation of delineators ( road way indicators), hazard marker and object markers), 80-100 cm high above ground level, painted at alternatively black and white in 15 cm wide strips, fitted with 80 x 100 mm retangular or 75mm dia circluar reflectorised panels at the top, buried or pressed into the ground and conforming to IRC -79 etc, complete (as per MORT&H specification no 806).

1.Providing Road Furnitures at km 0/0-4/850 of Hosur Inner Ring Road

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Providing and erecting Single sided Double Guard Metal Beam Crash Barrier System 1.70m high, comprising of 3mm thick wall “W” beams posts and spacer channels shall be made by cold roll forming using HR conform to IS 5986 Fe 410/360 and dip galvanized having Zinc Mass of 550gms/ sqm, minimum 950mm above road/ ground level fixed on ISMC series channel vertical post 150x75x5mm spaced 2m center to center 312mm x 83mm flange width x 3mm thick, 4318mm long post directly embedded in the concrete (M15) pit size 350x350x800mm for a depth of 750mm below ground. All fixing bolts and nuts hot dip galvanized conforming to IS:1367 clause 4.60 all complete as per Technical Specification and as directed by the Engineer-in-charge

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Proving and fixing Solar powered Traffic Blinkers of 30cm dia with Polycarbonate Dome 5mm Red of Led 150 Nos. iri each Red Blinkers Light - 1 No. with Red / White / Blue Led Blinkers Delineator Solar Panel : 12v 50w Solar Panel — 1 No. 12v 18 AH Battery - 1 No. with Box, Solar Circuit Controller Board Box. Straight Pole : MS Pole 3” dia 2.5mm thick 18 Feet height pole (1 No.) with 2 Feet under ground pole foundation, pole painting including transportation charges, installation charges etc., complete as per standard specification.

2. Providing Road Furniture at Km 17/0-20/2, 21/6-26/0, 33/4-36/0, 37/8-38/0, 38/2-38/4, 39/320-39/8 of Rayakottai - Athipalli road

Calculation of SubTotal, GST and Total Amount carried out by system automatically

Basic cost of value put to tender as per estimate

Add GST at 18%

Total Value put to Tender

Negotiated Percentage

Final Negotiated Value

Add GST at 18% of Final Negotiated Value

Total Value of Contract Including 18% of GST

Basic cost of value put to tender as per Estimate

Quoted Rate in Figures (Total Value of Contract Including 18% of GST )