Highways Department Tender

Road C

Road D

Supplying of Solar Raised Pavement Markers made of polycarbonate molded body, solar powered, LED self- illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable o providing total internal reflection of the light entering the lens face in passive mode. The product shall support a load of 13635 kg tested in accordance to MORTH and ASTM D4280 Type H. The product should be resistant to water ingress according to IP 65 standards with IS 12063: 1987 Category 2 and should withstand temperatures in the range of -7 C to 70 C. Flashing rate and color of lighting is to be provided as per requirement. There should be minimum current losses of less than 20 micro-amperes in sleep-charging mode to enhance product life and single charge should provide for a minimum autonomy of 50 hours. The height, width and length shall not be less than 10 mm x 100 mm x 100 mm. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by the engineer. Warranty Certificate and test reports confirming to compressive strength as per MORTH circular shall be obtained from the manufacturer and submitted to the engineer-in-charge. Two Years Warranty Certificate for Solar RPM for the Quantity installed and a certified copy of test reports from an independent test laboratory conforming to water ingress shall be obtained from the Manufacturer by the contractor and submitted to the engineer-in-charge. Solar Raised Pavement Marker / Solar Road Stud

Road A

Road B

Road C

Road D

Providing and erecting of Retro - Reflectorised Cautionary, Mandatory and Informatory signs {with definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 —09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2. lOm from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrète 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012 ( as per MORT&H Specification No.801). 60 cm equilateral triangle

Road A

Road B

Road C

Road D

Providing and erecting of Direction and Place Identification Retro-reflectorised Sign made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 —09, specification and fixed over 2mm thickAluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.6Om below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro- reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012. (as per MORT&H Specification No.801) for sign having area upto 0.90 sqm )Type IV

Road A

Road B

Road C

Road D

Providing and fixing of Retro Reflectorized Overhead Cantilever lnformatory sign made of cube corner Micro Prismatic grade sheeting conforming to Type XI standards of IRC67 - 2012 and ASTMD4956 — 09, specification and fixed over 2mm thick aluminum sheet fixed on back supporting frame mild steel L angle of size 50mm x 50mm x 6mm. The Vertical support post for the installation of overhead sign Gantry shall be made of 300NB (Nominal Bore) MS Pipe with 12mm thick with a ground clearance of 6 meters along with 80NB (Nominal Bore) MS Pipe with 4mm thick and 40NB (Nominal Bore) MS Pipe with 3.20mm thick support posts. MS Base plate of size l200mm x l200mm x 25mm and MS Top plate of size 900mm x 1650mm x 16mm to be used to hold the sign board at the top and bottom respectively. MS Stiffener plates 8mm thick of sizes 420x420, 682x420, 288x288, 288x927 & 44x 130 are to be used. Anchor bolts of dimension 25mm dia and l000mm length are to be used as fixtures. The approved direction information should be digitally printed and should have 70% of the co- efficient of Retro-reflection values against the values as mentioned in Table 6.9 of IRC67 — 2012.The Latex printer used for digital printing should use inks with low VOC emissions and have green guard, eco logo certificates as per UL 280 1 standards. The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance and a certified copy of three years Outdoor exposure report shall be obtained as per IRC 67-20 12 (As per MoRT&H specification No.80 l). Cantilever sign shall be installed at the site as per the approved structural and foundation drawing provided in the tender document and including cost and conveyance of all materials, equipment, machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer-in- charge etc., complete.Digitally printed Retre Reflectoriesd over head Gantry Information Board

Road B

Road C

Road D

Providing and erecting Single sided Double Guard Metal Beam Crash Barrier System 1.7Om high, comprising of 3mm thick wall "W" beams posts and spacer channels shall be made by cold roll forming using HR conform to IS 5986 Fe 410/ 360 and dip galvanized having Zinc Mass of 550gms / sqm, minimum 95Omm above road/ ground level fixed on ISMC series channel vertical post l50x75x5mm spaced 2m center to center 312mm x 83mm flange width x 3mm thick, 4318mm long post directly embedded in the concrete (M15) pit size 350x350x800rnm for a depth of 750mm below ground. All fixing bolts and nuts hot dip galvanized conforming to IS: 1367 clause 4.60 all complete as per Technical Specification and as directed by the Engineer-in-charge Metal Beam Crash Barrier Type - A, "W" Double Guard

Road B

Road C

Calculation of SubTotal, GST and Total Amount carried out by system automatically

Basic cost of value put to tender as per estimate

Add GST at 18%

Total Value put to Tender

Quoted value

Final Quoted Value

Add GST at 18% of Final Quoted Value

Total Value of Contract Including 18% of GST

Basic cost of value put to tender as per Estimate

Quoted Rate in Figures (Total Value of Contract Including 18% of GST )