Highways And Minor Ports Department Tender

Towards the supply of Universal Digital Penetrometer capable of conducting test as per ASTM D5, and IS 1203:1978 with the following features:- • Opto-electronic / Laser/ LVDT based depth detection & measurement system • Display resolution of penetration depths in tenths of units(0.01mm) • Magnifying lens for adjusting needle tip /cone tip exactly on the sample surface. To be supplied complete with the following items for bitumen penetration, • Weight of 50 Grams -1 No. • Penetration cup of 55mm diameter x 35mm height - 1 No. • Transfer dish - 1 No. • Penetrometer Needle - 1 No. • Needle Holder 47.5g ± 0.05g - 1 No. • Thermometer ASTM 17C (+19 to 27 °C) - 1 No. including warranty period of 12 months from the date of supply or installation whichever is later.

Digital Ductility Testing Apparatus

Towards the supply of Digital Ductility Testing Apparatus capable of conducting the tests as per ASTM D113 with the following features:- • Cooling arrangement with required compressor provision • Equipped with testing three specimens simultaneously • Electric pump circulator and heater. • The temperature is controlled by digital temperature controller with two rates of travel are to be provided i.e. 5cm/min and 1cm/min. • Suitable for operation on 220V,50 Hz, single phase, AC supply. including warranty period of 12 months from the date of supply or installation whichever is later

Rolling Thin Film Oven

Towards the supply of Rolling Thin Film Oven capable of conducting the test as per ASTM D2872 with following features:- • Low thermal mass RTD.;• Over temperature safety cutout ;• Double walled temperature cabinet • 16-Gauge welded steel exterior;• 18-Gauge corrosion resistant Stainless steel interior • Insulation with 89mm high density fiberglass ;• Programmable Microprocessor UL listed controller • 4 digit red LED temperature display;• 4 digit green LED for temperature set points • Including Thermal protection which prevents oven in event of control failure;• Temperature range: ambient to 200deg C; • Double exhaust vents;• Needle valve for air flow adjustments;• Air pressure gauge - Range (0 to 100 psi); • Heat exchanger - 5/16 inch Dia. copper tube;• Electrical supply : 230V AC supply, 50Hz single phase • Dimension : 1016x660x915 mm;• Estimated weight : 100 kg ;including warranty period of 12 months from the date of supply or installation whichever is later.

Digital Marshall stability Apparatus

Towards the supply of Digital Marshall stability apparatus of -100kN single speed for 4” / 6” dia. sample capable of conducting the test as per MS-2 and IS 17127:2019 including calibration certificate with the following features :- • Load frame, • Holder pin, • Power cable, • Load transfer bar, • Steel ball, • Electronic kit indicator containing . Load cell with adapter and cable . Displacement sensor with cable • 4” / 6” dia. sample mould assembly with . Rammer . Extractor . Round plate . Dummy plate . Handle pipe . Breaking head. Pedestal(4” / 6” sample) including warranty period of 12 months from the date of supply or installation whichever is later.

California Bearing Ratio testing machine

Towards the supply of California Bearing Ratio testing machine capable of conducting test as per IS 2720 Part XVI with the following features:- • Compact, Bench top design, Rapid Platen Adjustment Complete with stabilizing bar Options for mechanical or electronic measurement • Suitable for operation on 220V, 50Hz, single phase, AC supply;• Digital Indicator ;• Mode of Display: Micro controller Multiline, Alpha numeric LCD Display for all simultaneous Channel (No Need for channel Selection);• Load Cell, Capacity: 50KN compression type;• Three speed 1.5 mm/min, 1.25 mm/min & 2.5 mm/min, Maximum: 110% of the rated capacity • Sensing: Strain gauges in full bridge configuration;• Displacement Transducer Range: 0-20 mm with 3m long cable • Sensing Element: LVDT ;The equipment shall be supplied with ;•Laptop computer (minimum Intel i5 Processor, 8Gb Ram) loaded with licensed Microsoft Windows 10 OS (Lifetime Free update) – 64 bit;•MS Office bundle software valid for 5 years and other suitable software for conducting all the above tests with recording and analyzing.;including warranty for period of 12 months from the date of supply or installation whichever is later.

Automatic California Bearing Ratio Test Apparatus

Towards the supply of Automatic California Bearing Ratio Test Apparatus capable of conducting test as per IS 2720 Part XVI. with the following features:- • Motorized Electronic with Data Acquisition system;• Geotechnical software for testing, analyzing and Reporting; • The software should allow selection of British/Indian standards for analysis.; • Tests are to be performed in SI, Imperial or Metric units.; • Test information is to be presented on Menu driven screen.;• Each package guides through the test procedures is to be in very user friendly way.;• A database setup to store and manage completed analysis records with MS access as default system.; • The software has to read the data format for analysis from Data Aacquisition System;• An option to enter the data manually and save; • With extensive search functions based on date of analysis, Analysis done by different user accounts or search based on duration etc, for easy retrieval of old data.; • The default reports shall be automatically generated in crystal reports and to be printed directly.;• The reports shall be exported to word, excel or pdf formats.; • Customizable report header / footer; • The inbuilt utilities include master unit conversation calculator, besides the normal and scientific system calculators.; • Database backup and restore facilities ;• Complete user activity logging ; Special features and graphs for CBR analysis software • Manual data entry facility ;•To find out CBR value in % at 2.5 mm and 5mm penetration.;• Graph for load vs penetration (Top side, Bottom side and both).;• Graph correction facility ; • Graph expand facility.; With Software for the following tests •Unconsolidated undrained triaxial test;•Consolidated undrained triaxial test;• Consolidated drained test; •Direct / Residual shear test;•CBR test;•One dimensional consolidation test;including warranty period of 12 months from the date of supply or installation whichever is later.

Automatic soil compactor

Towards the supply of Automatic soil compactor capable of conducting test as per IS 2720 Part VIII complete with the following features •Motor driven mechanical compactor for soil compaction in 100 mm or 150 mm dia moulds. •Two rammers with different stroke length that should travel across the mould and the table rotates the mould in equal steps on a stable base. •The number of blows per layer can be set at the beginning of the test. • Rammer - circular faced 50mm dia. adjustable to 2.6kg or 4.9kg weight •Drop - Adjustable to 310mm or 450mm. •Digital display for counting the number of blows. •The equipment should be suitable for operation on 220 V, 50 Hz, single phase, AC supply including warranty period of 12 months from the date of supply or installation whichever is later.

Automatic Vicat’s Apparatus

Towards the supply of Automatic Vicat’s Apparatus for setting time test on Cement/mortar/gypsum conforming to EN 196-3, 13279-2, 480-2, IS 4031 PART 4& 5, ASTM C191, C187 complete with the following accessories: • initial setting time needle 1.13 mm dia,1 mm diameter needle mould •Needle for final setting test ; • Cylindrical probe for consistency test; • Accessory for needle continuous cleaning and in-water testing ; touch screen display• Graphic printer; • USB port for data storage, export to PC and firmware upgrade and Ethernet port for PC / network communication and network mode to independent units; • Minimum 16 GB Internal permanent memory on SD card •To be supplied complete with necessary software for remote PC control including LAN cable To be supplied complete with the following features • Fully automatic test cycle; • Easy re-call of test settings from test-profiles-database • Easy programming of customized test including: test start delay, penetration points positions, manual or automatic penetration rate, free or driven mode, holding intervals, automatic end- test detection.; •Automatic measurement of initial and final setting time;• Easy calibration menu Including warranty period of 12 months from the date of supply or installation whichever is later.

Digital Flexural Testing Machine

Towards the supply of Digital Flexural Testing Machine (100kN) Conforming to IS 516, BS: 1881 and ASTM C78 with the following accessories: •Suitable frame ; •Double action hydraulic pump ; •Self- Aligning roller assembly ; •Hydraulic jack provided with retraction spring for testing beams of 100x 100x500mm and 150x 150 x 700mm;•Suitable for operation on 220V 50Hz, single phase, AC supply Including warranty period of 12 months from the date of supply or installation whichever is later.

Automatic Blaine’s Apparatus

Towards the supply of Automatic Blaine’s Apparatus capable of conducting tests conforming to ASTM C204, EN 196-6, IS:1727, 4031, 4825 with the following features: •Automatic control of the movement of fluid until the upper mark.;•Automatic sensing of the upper & Lower marks ensuring error free repeatable measurement of the time taken for the liquid column to fall.;•Automatic Measurement of temperature during the test using a probe including Automatic correction of formula for calculation of the Blaine value per IS: 5516 with variation in temperature.;• Facility to operate in either standalone Mode or through a computer controlled system complete with software Login Facility.;•Report Generation based on Date/ Time. User type & type of cement in Excel or equivalent format. including warranty period of 12 months from the date of supply or installation whichever is later.

Rebar locator Profometer 650AI

Towards the supply of Rebar locator Profometer 650AI capable of conducting corrosion measurement conforming to ASTM C-876 consisting of Profometer with the following features:- •Touchscreen, •Universal probe with probe cart, •Probe cable 1.5 m (5 ft), •Power supply, ;•USB cable, DVD with software; •Documentation, •Activation key; •Carrying strap and carrying case ; •Upgrade kit to Profometer Corrosion consisting of interface box, ;•Cable coil of length 25 m (82 ft) with clamp, ;•DVD with software, •Documentation and Carrying case ;•Profometer Corrosion rod electrode, with spare parts, cable including spade terminal adapter and copper sulphate (250g);•Profometer Corrosion one wheel electrode, with telescopic handle, encoder, cables, spare parts, tool kit, copper sulphate (250 g), citric acid (250 g) etc complete ; including warranty period of 12 months from the date of supply or installation whichever is later.

Multipurpose Universal Testing Machine

Towards the supply of Multipurpose Universal Testing Machine - 2000KN Servo Controlled Machine capable of conducting tests conforming to IS 1828-part 1:2005 with the following features:- • Hydraulic power system, • Microprocessor control unit,; • Clearance for tensile test shall be 50-850 mm; • clearance for compression test shall be 0-700 mm ; • User interface with large graphic display with keyboard; • Data Acquisition testing system and related legal and licensed version of Interactive software. With the following accessories;• 2000kN Loading Unit; • Servo Pump System ; • Clamping Jaws for Round Specimen 08-70mm; • Clamping Jaws for Flat specimen 0-40mm; • Clamping Jaws for HT Strand wires 12.7 and 15.2mm;• Bend Test 180 degree attachment; • Bend Re-bend Test attachment ; • Electronic Extensometer with 25mm & 50mm gauge lengths & 600 mm for HT strand wires; • Shear Test Attachment 6,8,12,16,20mm; • Shear Test Attachment 25,30,35,&40mm ; • flexure test attachment; • wire rope test attachment 0.12 - 13.2 mm;The Servo-pump with the following features; • Standalone close loop automatic control console to perform tests under control of: Load/stress and Displacement by suitable transducers.• The Rate of strain shall be adjustable between 0.00025 /s and 0.0025/s and Rate of stress 1 to 50 N/mm2 per second.including warranty period of 12 months from the date of supply or installation

Digital Compression Testing Machine

Towards the supply of Digital Compression Testing Machine -2000 KN plates and accessories Conforming to IS 516 & IS 14858:2000. with the following features: •Digital Indicator having 4-Digits display calibrated in Kilo Newton (KN) and preset to maximum load capacity fitted with micro switches.;•Electrically operated pumping units provided with control knob to adjust the pace rate and provided with a pace indicator to indicate pace rate on a Bar Graph.;•The pace shall be controlled manually while the test is in progress including warranty period of 12 months from the date of supply or installation whichever is later.

Universal Testing Machine

Towards the supply of Universal Testing Machine (1000KN) capable of conducting tests conforming to IS 1828-part 1-2005 with the following features; • Hydraulic Jaw Set with a resolution of 0.01KN ;• Clearance for tensile test shall be 50-850 mm; • Clearance for compression test shall be 0-700 mm ;• Clearance between columns 650mm, • Ram Stroke: 250mm ;• Piston speed at no load should be 0-50mm/min• Fully enclosed and protected load measuring system. load frame with rigid construction.;• Motor driven threaded columns for up/down movement of lower crosshead for quick change over of specimen, grips and attachment.• Power pack should generate a maximum pressure of 200 kgf/cm².;• System should have high precision, sealed and accurate pressure transducer mounted in the Hydraulic pressure line of the loading unit;• System should have Ergonomically designed micro process unit selection for load, displacement.;• Results should include Load vs Displacement curve, Maximum displacement, UTS, %Elongation, youngs Modulus and proof stress; System should include the following accessories:;• Clamping jaws for round specimens 8-25mm, 25-45mm; • Clamping jaws for flat specimens thickness: 0-40mm ; • Flat specimen width: 70mm for tension test, ; Pair of compression plates; • Electronic extensometer strain gauge type with gauge length 25mm and 50 mm; • Brinell test attachment, • Bend/ Rebend test attachment , • Flexural test attachment. System shall be supplied with following features:• Software should have the features for data analysis like Mean deviation, Frequency Distribution, Skew Diagram, Histogram and graph.;• System should be Calibrated in accordance with BS:1610 and IS standards and it should comply with grade A of BS 1610:1964 and grade 1 of IS: 1828-1991.;• Power supply: 440V, 50HZ, three phase, Ac Supply. • Computer and printer should be supplied with the system having minimum specifications as follows; • i5 or better,4 GB RAM, ;•Processor, 256MB , 250GB HD Drive, CD-ROM Drive, ;•Mouse or pointing device and keyboard supported by Windows 10 Pro 64 bit and MS office bundle.;• Monitor that supports 1024X768 resolution and 32-bit color, 2 USB serial port adapter per machine;• Windows compatible sound card and speakers (for audio playback) • Additional USB ports for measuring devices, barcode scanners, printer;• One integrated serial port (not USB) where possible, Lan card for connecting with electronic panel .;including warranty period of 12 months from the date of supply or installation whichever is later.

Desktop systems with licensed latest Windows OS 64 bit

Towards the supply of Desktop systems with licensed latest Windows OS 64 bit With the following futures:- • Genuine Window 10 Pro 64 bit ;• intel core i5 ;• 8 GB RAM ;• 1 TB Harddisk ;• 2GB Graphics memory ; • 19.5 inches monitor ; including warranty period 36 months from the date of supply or installation whichever is later.

Multi-functional Plotter

Towards the supply of Multifunctional wide format colour plotter, • size A0 to A4 with licensed software; including warranty period 60 months from the date of supply or installation whichever is later.

Video Camera Unit

Towards the supply of Drone CAMERA With the following specification and accessories:- • Aerial Video Recording & Photography,;• Sensor Size of 1/2.3 inches, ;• CMOS, Optical Zoom of 6x,; • Max speed 50 to 55 mph with Flight Time of 27mins, ;• 10 million Pixels, • Remote Distance of 5 to 7km control range with FPV Operation,;• 2 control Channels, • APP Controller Connectivity,;• 4K HD Video Recording, • Digital Video Zoom,;• D log-M and HLG HDR for high dynamic range recording and 10-bit support. • Footage that is suitable for high-end grading and editing applications; including warranty period of 12 months from the date of supply or installation whichever is later.

Towards the supply of 4K Professional Camcorder with Super 35 Camcorder Kit with Zoom Lens or equivalent, With the following specifications/ accessories:- • E Mount Locking Sys Mechanical Adapter, • Variable Electronic Neutral Density ND 2 to 7 Stops Filter, • Built in Mic Viewfinder and Short Gun Mic holder mount with Latest Rolling Shutter Technology, • Wi-fi Adaptor,• Controllable Zoom Focus Iris & White Balance as well as Recording Functions, Control With mobile device., Internal Recording in both DCI 4K & UHD 4K UPTO 59.94 FRAMES/SEC, • Camera Tripod, • Carry case Including warranty period of 12 months from the date of supply or installation whichever is later.

Still Camera

Towards the supply of SLR Camera Series or equivalent with Selectable Lenses With the following specification / accessories:- • 20 MP FX CMOS Sensor; • 14fps shooting (Video Mode); • 4k Ultra HD Video Recording at 30fps • Built in Wi-Fi ; • Bluetooth and GPS; • Touch Screen LCD Monitor; • Expeed 6 image processor or equivalent; • 64Gb xqd Memory Card 2nos, • Shoulder Bag; • Zoom Lens 200 500mm f/5.6ED or equivalent; • Normal 50mm; • Wireless TTL Flash Unit; • Free wave Wireless remote Including warranty period of 12 months from the date of supply or installation whichever is later.

Video editing Unit

Towards the supply and installation of Video editing Unit consisting Intel core i7 10th Gen Processor (Windows Platform) with Asus B250M Plus Motherboard or equivalent With the following accessories:- • 64GB DDR4 RAM; • 350Gb SSD wd HDD ; • 2TB SATA WD Hard disk (2Nos) ;• W5000 G Force 8Gb / ASUS GAME Engine or equivalent ; • Cooler Master Cabinet or equivalent (Industrial Cabinet) • Cooler master 750W SMPS or equivalent, Digital Intermediate Panel Board; • Keyboard and Mouse, Editing Console Table; • Blue Ray Writer; • LED Monitor -2 Nos ; • Television 32inchs Preview Monitor ; • Monitor Speaker -2 Nos; • HDMI Splitter with Cable (According to the length) • Speaker Stand 2nos, Interconnecting Cables (Signal / PWR / BBand / Ethernet / HDMI , Sound Proof & Acoustic (Sq Ft Rate 1200/sqft) ; • Lightings / Emergency Light.; • Software required • FCP / Premier Pro (Any One); • Photo Shop & After Effect ; • color correction software Windows 10 / 64 bit pro and MS Office Bundle. Including warranty period of 12 months from the date of supply or installation whichever is later.

Sound Recording Editing Unit

Towards the Sound Recording Editing Unit consisting Intel core i7 10th Gen Processor (Windows Platform) with Asus B250M Plus Motherboard or equivalent With the following accessories:- • 64GB DDR4 RAM; • 350Gb SSD wd HDD ; • 2TB SATA WD Hard disk -2 Nos; • W5000 G Force 8Gb / ASUS GAME Engine or equivalent • Cooler Master Cabinet or equivalent (Industrial Cabinet), • Cooler master 750W SMPS or equivalent • Keyboard and Mouse • BlueRay Writer • 22 inch LED Monitor or equivalent - 2 Nos • Television 32inchs Preview Monitor, • SSL Soundscape 32 DaW Hardware • Digital Portable Mixing Console o3d • Audio Interface (Audio Card) • 1000C Condenser - 2 Nos • Headphone - 3 Nos • Studio Monitor Speaker - 2 Nos • HDMI Splitter with Cable (According to the length), • Mic Stand - 2 Nos • Speaker Stand - 2 Nos • Working Table (Mixer and Console Table with Rack) • Console and Studio Chairs, Pop Filter (Blow Cutter) • Interconnecting Cables (Signal / pwr / Ethernet / HDMI • Sound Proof & Acoustic for Console and Vox Room (@ Sq Ft Rate 1200/sqft) • Vox Room - 200 sqft • Console cum Engineer Room - 250 sqft • Air-condition plant 4ton (2X2), Lightings / Emergency Light / Sign Boards Softwares required are: • Protools Ver.10 or 12 & SScape DAW Software (Digital Audio Workstation) or equivalent • Noise Cleaning Software • Window 10 pro 64bit and MS office Bundle including warranty period of 12 months for from the date of supply or installation whichever is later.

Multifunctional colour copier machine

Towards the supply of All in one color printer, digital color MFD (Print/Copy/ color scan/ stores/ scan to e-mail and folder) with the following features:- • All in one color printer Towards the supply of All in one color printer, digital color MFD (Print/Copy/ color scan/ stores/ scan to e-mail and folder) with the following features:- • 30 cpm/ ppm copying/printing Speed • Up to A3 Size • Digital inbuilt Network Printer • Copier Color • Duplex Printing & Copying • DADF (Duplex Automatic Document Feeder • 3 GB RAM • 250GB Hard Disk • 2 Auto Trays ( 550+550)Sheets capacity • 100 Sheets Bypass • 200X1200 dpi Resolution • 1.5kw or less Power Consumption • 25% - 400% Zoom Ration • Rotate Collate • Toner Yield – Black – 36000 copies; • Color (C/M/Y) – 19000 copies each • Drum Yield – Black – 84000 copies • Color (C/M/Y) - 66000 copies each • Machine Life - 10 Lakh Copies, • VALUE ADDITION: Movable Trolley with Shelf and 2KVA Stabilizer Including warranty period of 12 months for from the date of supply or installation whichever is later.

Towards the supply of All-in-One Wireless colour Printer of Ink Tank Type color Printer with All-in-One (Print, Scan, Copy) functionality with ISO standards with the following features:- • • Wi-Fi Connectivity • USB, with suitable printing application. • Compatible with Windows 10, Windows 8.1, Windows 7 SP1. • Power requirements of 200 to 240 V • 50/60 Hz • 1.2 inch LCD diplay on printer(mono) • 8.8 ipm (Black) • 5 ipm (Colour) • As per ISO standards. Page size supported - 4.0"x6.0" till A4 / Letter / Legal / A5 / B5 with • Print resolution of 4800 x 1200 dpi, • Compatible Ink Bottle - GI-790 (BK), GI-790 (Cyan, Magenta, Yellow), • Page yield of 6000 pgs (BK), 7000 pgs (color) – with 1 set of all 4 ink bottles inside the box(As per ISO standards) including warranty period of 12 months the date of supply or installation whichever is later.

Towards the supply of Laser Printer with All-in-One (Print, Scan, Copy) Functionality with the following features:- • with the following features:- • Printer Output- Mono (Black) . • USB 2.0 Connectivity. • Wi-Fi, with software for printing. • 6.9cm BW LCD Display panel. • Compatible with 32 / 64bit Windows 10, 8.1, 8, 7, Vista, Windows Server 2012 R2 (64bit), Windows Server 2012(64bit), Windows Server 2008 R2(64bit), Windows Server 2008, Windows Server 2003 R2, Windows Server 2003, • Print Language-UFR II LT, PCL 6; • Device Memory- 512MB • Duplex • Page size supported- A4, B5, A5, • Legal, Letter, Statement, Executive, • Government Letter, Government Legal, • Foolscap, Indian Legal • Custom (Minimum 76.2 x 210mm to Maximum 216 x 356mm) • Print resolution- 600 x 600dpi • Cartridge 337; Page yield-2400 pages. • As per ISO standards, (Digital Multifunction Laser Printer, Black, Standard) Including minimum warranty period of 12 months from the date of supply or installation whichever is later. .

Garden maintenance machine

Towards the supply of Brush cutter with the following features;- • with the following features;- • Powered by 42.7 cc with 2 Stroke Air-Cooled Engine, • Fuel tank capacity of 0.9 Ltrs., • Dry Weight 8.0 kgs, • Cutting Tool Steel Blade, • Nylon Head & 15 metre Nylon Rope Including warranty period of 12 months from the date of supply or installation whichever is later.

Towards the supply of Lawn Mower with the following features:- • Powered by Electric Motor,;• 3 Phase/ 440V, ;• 5 HP/2880 RPM, ;• Cutting Width of 45 cm, ;• Cutting Height of 10-100 mm (6 Stages),;• Straight Blade• Steel Cutting Deck ,;• Cable Length 4;including warranty period of 12 months from the date of supply or installation whichever is later.

Vaccum Cleaner

Towards the supply of Vacuum cleaner with the following features:- • 230-240/50Hz Voltage, • 1350 W power, • 54LPS airflow with Suction Power of 22 kPa, • Tank Volume of 35 Litres, • Dimensions cm (LxWxH) - 36x36x76, • Weight - 9 Kg including warranty period of 12 months from the date of supply or installation whichever is later

Laptop and Desktop computers

Towards the supply of Laptop with the following specifications;- • Intel core i7 1165G7 • 8GB DDR4 • 512GB SSD • 15.6”(1920X1080) • 2 GB dedicated Graphics/HD • Webcam Backlit Keyboard • Finger Print Reader • WIFI 6+BT 5.0 • maximum weight of 1.8Kg MS Office licensed software. • WIN 10 PRO – 64 bit MS Office bundle Including warranty period of 36 months from the date of supply or installation whichever is later.

Towards the supply of Desktop systems with licensed latest Windows OS 64 bit with the following futures:- • Genuine Window 10 Pro 64 bit • intel core i5 • 8 GB RAM • 1 TB Harddisk • 2GB Graphics memory • 19.5 inches monitor Including warranty period 36 months from the date of supply or installation whichever is later.

Towards the supply of MS office 2019 standard version

Calculation of SubTotal, GST and Total Amount carried out by system automatically

Basic cost of value put to tender as per estimate

Add GST at 18%

Total Value put to Tender

Negotiated Percentage

Final Negotiated Value

Add GST at 18% of Final Negotiated Value

Total Value of Contract Including 18% of GST

Basic cost of value put to tender as per Estimate

Quoted Rate in Figures (Total Value of Contract Including 18% of GST )