Corporation Of Chennai Tender

Drilling holes for piles of finished diameter of 1000 mm in all types of soil, pavement, all types of rock,weathered rock,Hard rock using rotary drilling equipment for depths above 20m to 30 m depth including all equipment, tools, labours, consumable, Bentonite, Casing materials and removal of all equipment,materials and debris on completion of concreting etc. complete as directed by the Engineer. for above 20m to 25 m depth

supplying fabricating and driving 6mm thick permenant MS linear for piles of 1000 mm dia

supplying fabricating and driving 6mm thick permenant MS linear for piles of 750 mm dia

BORED PILE 450 mm Dia Providing and installing Bored cast-in-situ reinforced cement Concrete pile of specified diameter and length below the pile cap in RMC M25 concrete to carry a safeWorking load not less than specified, excluding the cost of steel reinforcement but including Bentonite solution METER PILE machinery charges labour chargers etc., all complete.(Length of pile for payment shall be measured from Bottom pile to the bottom of pile cap).

Stripping of concrete at pile top of piles for the required depth to expose the pile reinforcement so as to anchor the same with pile cap reinforcement ,bending ,cleaning including labour charges, hire charges for tools and plants and all other incidental charges etc complete including cutting extra length of reinforcement if found necessary and as conforming MoRTH specification as directed by the Engineer. ( Source :MoRTH- Standard data book for analysis of rates,First revision, Page - 441 )

Supplying and placing of Ready Mix M60 Graded of Concrete confirming to IS 456/2000 for Reinforcement Cement Concrete Structural elements under controlled water cement ratio using 20mm and down graded machine broken granite stone jelly including transportation Vibration charges and pumping excluding cost of centering and shuttering and reinforcement but including curing, finishing etc as directed by departmental officers

Supplying and placing of Ready Mix M30 Graded of Concrete confirming to IS 456/2000 for Reinforcement Cement Concrete Structural elements under controlled water cement ratio using 20mm and down graded machine broken granite stone jelly including transportation Vibration charges and pumping excluding cost of centering and shuttering and reinforcement but including curing, finishing etc as directed by departmental officers

Supplying and erecting centering for sides and soffits including supports and strutting up to 3m high for plane surface such as RCCslab, rectangular beams, ‘TEE' or ‘L’ beams,lintels,bedblocks,staircase waists and landing slabs, landing beams ,canopy, etc. With all cross bracings using mild steel sheets of a size 90x60cmx3.175mm and 10 gauge stiffened with welded mild steel angles of size 25x25x3mm for boarding laid over silver Oak(Country wood) joists of size 10x6.5cm spaced at about 90cm centre to centre and supported by casuarina props of 10 to 13cm dia spaced at 7.5cm centre to centre etc., complete

Supplying and erecting shuttering including necessary supports for plane surface in foundation and basement for RCC column footings,pintol blocks, plinth beam, staircase steps, critical steps, critical piers,etc.,using mild steel sheets of size 90x60cm and 10 gauge stiffened with welded mild steel angles of size25x25x3mm for boarding laid over silver Oak (country wood) joists of size 10x6.5cm spaced at about 90cm centre to centre and supported by casuarina props of 10 to 13cm dia spaced

Supplying and erecting centering for the vertical plane RCC concrete walls of supply channel,Retaining wall Etc upto 180 CM height with necessary supports all cross bracing with mild steel siexe of 90 cm X 60 Cm and gauge BG 10 stiffened with welded mild steel angles of size 25x25x3mm for boarding laid over silverOak /country wood joist of size 7.50 cm x 5.0 cm Spaced @about 90cm c/c and supoort by casurina prop of 10 cm to 13 cm spaced @ 75 cm C/C etc complete complying with standard specification and as directed by the department officers (SWD)

Supplying and erecting centering for sides and soffits including supports and structting upto 3m high for plane surfaces such asRCC coloumns,top and bottom slabs of boxing. sill labs,sun shades,etc.,with necessary facia using mild steel sheets ofsize 90x60cm and 10 gauge stiffened with welded mild steel angles of size 25x25x3mm for boarding laid over silverOak (country wood) joists of size 10x6.5cm spaced at about 90cmcentre to centre and supported by casuarina props of 10 to 13cm dia spaced at 75cm centre to centre etc.,complete

Supplying and fabricating RTS / TMT STEEL rods including cutting, bending hooks, cranking, fabricating, assembling and laying in exact position, typing with soft steel wire 16 gauges, etc., complete conforming to BIS std.

Hire chrages for barricades minimum 3.0 height around the site premisses of 94 Kg/M using ISMC 100 as transom and verticals and 3mm thick sheet with bottom supports of ISMB 200 including nailing to the floor cost of fabrication transportaion lifting and placing in position using cranes painting ,reflective stickers ,provision for continous lighting arrangement in order ,in straight rows or as required at the site without hinderance to the traffic (the barricade shall remain tin the same location till completion of the work all barricading materials shall be disposed and taken away from the site by contrctor no additional pavement shall be made for extended period of contract

Paving the flooring with CEMENT CONCRETE TILES hydraulic pressed Antiskid tiles as per pattern design 20mm thick in cm 1:3 including pointing with colour cement etc., complete.(ISI)

Paving the steps with CEMENT CONCRETE STEP TILES hydraulically pressed Anti skid steps tiles of 20mm thick in C.M.1:3, including pointing with colour cement etc, complet ( I.S.I std)

Plain Cement concrete work 1:4:8 (1 cement, 4 river sand and 8 blue granite broken stone jelly 40mm gauge) including consolidation curing, etc. complete for foundation, etc. up to basement.

Earth work excavation for foundation in all kinds’ soils in varying depths including dismantling any masonry or roots met within foundation and shoring with planks, baling water if necessary and filling the sides with excavated earth including clearing and levelling site etc., complete with an initial lead of 10m.and lift of 2m

Dismantling of RCC work carefully clearing away the debrise as directed during execution

Dismantling plain cement concrete work and clearing the debris etc., complete.

Carting away the surplus earth/debris to a lead of 12km.including Loading, unloading and dumping in the Corporation Land as directed during execution

Supplying and erecting in position of Steel sections for elements like columns, beams, purlins,plates as per the drawing providing minimum grade of YST 310 as per IS 4923 for Rolled Tubular sections and grade E350 as per IS 2062 for all other steel elements and components. The materials of the all components should confirm to the relevant Indian Standard specifications. The elements shall be procured only from reputed manufactures of steel and certificates to the effect from the reputed manufacturers shall also be Furnished. The rate quoted shall include the cost of steel element, base-plates with holding down bolts and nuts to RCC, roof purlins, rafters, purlin sleeves,splices the members fixing accessories etc.,including welding as per IS 800 and IS 814 and grinding as per requirements, Blast cleaning SA 2.5 and applying one coat of Zinc rich primer and erecting in position using cranes, lifting and transportation of material to site and assembling as instructed by Engineer . The contractor shall also arrange to provide grouting with recommended materials as directed by the Engineer for holding down the bolts embedding to the concrete surface wherever necessary etc., complete

Providing, fabricating and fixing in position stainless steel hand rail consisting of 60mm outer dia at top and two intermediate pipe 20mm dia, including profile cutting, fixing in position, including 2nos of vertical balusters made of 50mm 8mm thick SS flat metal plates-balusters placed 1500mm c/c or at required spacing necessary anchor fasteners / approved fixing arrangements to the wall, welding using special electrodes for stainless stell welding, etc complete as per detailed drawings and as directed by the Engineer-in-charge.The stainless steel pipe shall be of non magnetic type stainless steel, with minimum thickness of 1.5mm and conforming to grade 316 of AISI.. for Staircase Handrail.adopt as per drawing

supplying and painting with coating with High Quality Powder with Coating Thickness of 60 to 80 Micron (+- 20 microns) with epoxy black stain colour including labour charges

supplying and fixing of panels shall be made out with 0.35 mm thick Pre coated Profile steel sheets at outer side and 0.35 mm thick Pre coated plain sheet at inner side of PUF. Total thickness of roof panel shall be 50 mm. PU must be CFC free, self-extinguishing, fire retardant type having density of 40Kg/CUM. (± 2Kgs).

Supplying and fixing of GI sheet gutter 3.15mm thick and fixing in clamps of thickness 10 mm of width 50 including cost of matterials and labour charges

Supplying and fixing P.V.C. pipe 110mm dia rain water downfall pipe as per ISI standard (I.S.4985) with door arrangements including P.V.C.Bend, shoes, grating with F.I.clamps 40mmx20mm of suitable size fixed to wooden plugs embedded in walls in cement mortar 1:3 ( 1 cement MTR and 3 river sand ) including cutting holes in walls and making good the same after fixing the plugs etc. Complete as directed during the execution.

Supplying and installation of strip seal expansion joint system catering to maximum horizontal movement up to 40mm complete as per approved drawings and standard specifications to be installed by the manufacturer or their authorized representative ensuring compliance to the manufacturer’s instructions for installation conforming to MoRTH specification for road and bridge works in the expansion gap provided in between decks over piers and in between deck with fatigue tested structural steel section at the nosing and and anchorage assembly including cost and conveyance of all materials cost of testing as per MoRTH specification including labour equipment’s andall other incidental charges for fixing joints etc., complete as per standard technical specification2607of MoRTH and as per the directions of Engineer in charge for Strip seal expansion joint over deck slab andapproach slab and as per the directions of Engineer incharge etc., complete.

Supplying and fixing of Deck sheet 1.2mm thick,including labour charges for fixingsetc complete

supplying and painting with two coats of ready mixed epoxy paint first class quality and of approved colour over existing painting metal structural using brush or mechanical sprayer including necessary scaffolding through cleaning washing clean removal of dirt etc.., complete and necessary plaster of paris putty etc., where ever requires (ISI Std.)

Construction of cast-in-sit Silt Catch Pit with Rain Water Harvesting Structure of inner size 600x600x600mm including necessary earth work excavation inclulding providing foundation in PCC 1:5:10 under walls 150mm thick and fixing vertical grating of size 450mm length x 155mm height and30mm thick on the storm water drain mouth, with RCC cast in situ wall of size 120mm in RCC 1:1.5:3 with steel of 10.60kg including fixing FRP Grating Cover with frame of size 700mmx700mm (Clear opening 600x600mm) - 10MT completing the finishing work etc., cost per each number. Using Hand Bore Set drilling of bore hole of 300mm dia upto 4.35m depth including shifting of the hand bore from one place to another place within 5km and filling in with 40mm HBG metal with 20mm dia PVC pipe 4kg/cm2

Supplying and fixing of SINTEX SECURITY BOOTH PVC PANEL Guard cabin - Of Dimension 3mx3mx7.5'H including cost of materials and labour charges for fixing.

Suppying and fixing of Stainless Steel Dustbin18 litre (10'' x 14'')

Supply of Store Pressure ABC Type 6Kg. MAP Base, 3A - 34B Fire Extinguisher including cost of materials and installation charges etc.., complete

Providing Stainless steel bollards with concrete filling

supplying and fixing Audio announcement system in the skywalk ahuja make PA amplifier model : SSA -5000Dp ahuja make Pa Microphone model:ACM -66CH Ahuja make 40W P A Horn speaker Model SUH-40 XT 2 crore 0.75 SQ.MM armed loud speakers cable Weather proof junction box Including testing and commissioning charges

supplying and fixing of signages board etc., complete

supplying and fixing Diplayboard etc., complete

supply and fixing Metal shoring for protecting residence along service road during pile drive etc., complete

Providing all equipment,kentledge, materials, instruments and manpower and conducting Initial Pile Load Test including preparation of pile, conducting observations and submitting Report, removing all arrangement, kentledge, etc., on Completion, but excluding cost of pile, complete as per IS:2911 Part-IV and MOST specifications and as directed by the Engineer.

Providing all equipment,kentledge, materials, instruments and manpower and conducting Routine pile load test including preparation of pile, conducting observations and submitting Report, removing all arrangement, kentledge, etc., on Completion, but excluding cost of pile, complete as per IS:2911 Part-IV and MOST specifications and as directed by the Engineer.

Chemical anchoring of reinforcement (lock fixing ) with 150 mm Depth over the existing RCC structure ,by using overlapping or welding for 12mm dia

Painting two coats with ready mix plastic emulsion paint of first class quality and of approved color over a priming coat including through scrapping,clean removal of dirt etc.., complete and including nessary plaster of parris ,putty wherever required and neat finishing etc.,(ISI STD)

Supply and erection of Grid tied SPV system for a capacity of 350 KWp using 1100 solar panels of each size 2mx1m with rated capacity of 320Watts each with necessary features to supplement the grid power during day time. Components and parts used in the SPV power plants including the PV modules, metallic structures, cables, junction box, switches, PCUs including installation, commissioning, transportation, insurance, 5 YEAR AMC/ CMC etc., should conform to the BIS or IEC or international specifications, wherever such specifications are available and applicable. (As per specifications enclosed)

Dismantling the existing Brick or Stone in clay walls under 3M high including carefully clearing the debris etc., complete.

Picking /cutting existing black top surface for 2 cm. to 10cm. Thick

Supplying and placing of Ready Mix M20 Graded of Concrete confirming to IS 456/2000 for Reinforcement Cement Concrete Structural elements under controlled water cement ratio using 20mm and down graded machine broken granite stone jelly including transportation , pumping and Vibration charges excluding cost of centering and shuttering and reinforcement but including curing,finishing etc as directed by departmental officers

Refilling with excavated earth in regular layers of 15cm thickeach including carefully ramming, watering, consolidating, etc.,complete for foundation and basement.

supplying of PVc pipe 160mm dia with ISI monogram(working pressure 6kg/Sq.cm)

Supplying and fixing of composite Fibreglass reinforced polymer manhole door with cover 900mm dia (cirucular) Heavy Duty (20 - MT) load capacity of approved brand confirming to BSEN – 124:1994. Product shall have top abrasion resistant layer of decorative grey granite finish confirming to test performed as per IS – 15658:2006. It shall also confirm “Permanent Set” criterion as per BSEN-124.Product should be tested in NABL accredited test lab for load capacity and permanent set. The lifting arrangement should have an insert of 5mm in SS 304 socket type with key hole.

Hire charges for diesel pumpset above 3Hp to 7.5Hp with fuel and crew charges including transportation

Construction of cast -in- situ Silt Catch Pit of inner size 450 X 450 X 450 mm including necessary earth work excavation including providing foundation in PCCb1:5:10 under wall 150mm thick and fixing vertical grating of size 450mm x 155mm x 30mm on the storm water drain mouth with RCC cast in situ wall of size 120mm in RCC 1:1.5:3 with steel of 9.25 kg including fixing FRP Grating Cover with frame of size 550 x 550mm (clear opening 450 x 450mm) -10 MT - completing the finishing work etc.

Providing laying, Spreading and compacting Graded Stone aggregates to Wet Mix macadam 250 mm thick specification including premixing the material with water at OMC in Mechanical Mix Plant Carriage and transporting the mixed material by tipper to site, laying in uniform layers with pavers in sub base/basecourse on well prepared surface and compacting with vibratory roller to achieve the desired density, etc.,including cost of material,labour charges,rentls for machinery,fuel and all other incidental charges .Complete as per clause 406 of MoRT& H Specifications.(COMPACTION BY VIBRO MAX ROLLER IS A MUST) (This rate is applicable only if the Work is carried out during NIGHT)

Supplying and placing of Ready Mix M40 Graded of Concrete confirming to IS 456/2000 for Reinforcement Cement Concrete Structural elements under controlled water cement ratio using 20mm and down graded machine broken granite stone jelly including transportation Vibration charges and pumping excluding cost of centering and shuttering and reinforcement but including curing, finishing etc as directed by departmental officers

Providing and laying 50mm consolidated thick Dense bituminous macadam using 0.24 Cu.m of 26.50-13.20mm 0.25cum of 13.20-2.36mm,and,0.23 Cu.m of 2.36 mm and & below and with 53.20kgs of VG30 (60/70 grade) bitumen for premixing per 10sq.mincluding cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to work site, spreading the mix to uniform thickness of 50mm with 9m paver finisher to the specified grades and cross sections and compacted by Pneumatic Roller to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20-30 tonne CMP with bitumen boiler, tipper trucks, 9m paver finisher, Pneumatic roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause505 of MORTH Rev-5 (This rate is applicable only if the Work is carried out during NIGHT and if it is laid by 9m Paver Finisher)

Providing Tack Coat 2.5 kg/10 m2 with Bitumen Emulsion (Rapid Setting 1)including cost of bitumen at the site, including labour charges for preparing the surface and applying required quantity of bitumen emulsion as Tack Coat using bitumen sprayer etc., complete over the primed surface as per clause 503 of MoRT& H SpecificationsRev.5 (This rate is applicable only if the Work is carried out during NIGHT)

Providing and laying Bituminous Concrete 40mm thick using 0.13Cu.m of 19.00-9.50mm,0.17 Cu.m of 9.5-2.36 mm Metal, and 0.26 Cu.m of 2.36 mm and below Metal of specified grading aggregates and0.012 Cu.m with 50.3 kg of VG30 (60/70 grade)bitumen for premixing per 10sq.m including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to worksite, spreading the mix to uniform thickness of 40mm with 9m paver finisher to the specified grades and cross sections and consolidated by 8-10 tone Pneumatic Roller to the required density etc., including labour for attending to paver to site etc. including hire charges and fuel charges for 20-30 tonne CMP with bitumen boiler, tipper trucks,9m paver finisher, Pneumatic roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH Rev-5 (This rate is applicable only if the Work is carried out during NIGHT and if it is laid by 9m Paver Finisher)

Cold milling to a depth of 40 mm

Providing Crashbarrier for the center median with M40 grade RMC over a levelling course of LCC 1:5:10 100mm thick as per sketch enclosed with top of 150mm and bottom of 610mm with a height of 985mm including shuttering ,reinforcement with 12mm dia RTS 11 Nos and rings with 12mm dia RTS at 230mm c/c,rendering smooth with cement at 1.5 kg per 1Sq.M and two coats of exterior emulsion painting etc.., complete as per the sketch enclosed and as directed by the Engineer -in-charges including fixing 2 nos ,PVC pipe of 110mm dia with 6kg/Sq..cm

Cuttting bituminous concrete /cement concrete surface of 300mm thick and width of 300 mm using machinaries (jack hammer ) including hire charges of machinaries and laboure charges etc..,

Supplying and placing of Ready Mix M15 Graded of Concrete confirming to IS 456/2000 for Reinforcement Cement Concrete Structural elements under controlled water cement ratio using 20mm and down graded machine broken granite stone jelly including transportation Vibration charges and pumping excluding cost of centering and shuttering and reinforcement but including curing, finishing etc as directed by departmental officers

Supplying and fixing of rubber molded grey primium concrete kerb of size 450X125X300 mm using M30 concrete the concrete shall be molded by table mount vibrated with polypropolyne fibres at 5% and curing compountd the rate shall include cost of materials,transportation,loading ,unloading charges and all taxes including necessary earth work ,pointing with CM 1:3 to full depth curing ,thread lining etc. complete

Providing LED light of HIPE30W CW in the roof including cost of mateial and labour charges for fixing

Wiring with 2x 1.5 sqmm (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A F.T. switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / Fan point (For Electronic regulator)

Wiring with 2x4 sqmm(56/0.3) PVC insulated SC unsheathed Cu.Conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15 A 3 pin non inter locking CS socket with continuous earth wire connection of 14 SWG TC wire , and making good of the concealed portion, with suitable colour for concealed Power plug point

Supply and fixng of TNEB Moter Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units (500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete

Supply and fixing of 4'40" W single box type flu.fitting complete with copper choke and condensor with TW round block on wall or ceiling with flu.tube with PVC unsheathed LEADS FROM TERMINALS TO THE FITTING- (SD-89)

Supply and fixing of 100 Amps TPN sheet double break switch with HRC fuse and neutral on suitable angle iron framework with MS cable entry boxes and with PWD earthing.

Supply and fixing of Horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure with 40A 4 pole MCB isolater as incoming and 12 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (like standard make)

Supply and run of 4 X 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade on 7/20 GI bearer wire for service connection mains etc, complete as per standard specifications SD.68

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supplying and Installation and erection Generators 100 K VA capacity with AMF panel including all labour charges et., complete

Supply fixing and maintenance of LED fitting of 90 W to 120 W with 7 years replacement guarantee (in place of 150 W SVL).

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Supply, Installation, Testing & Commissioning of Direct-view LED based dynamic color changing direct view flexible fixtures. Nodes shall consume 25W per 50-node strand maximum at full output at 24VDC input voltage. IP:Dry/Damp/Wet Location, IP66. Viewing Angle 105°, Lumens per node shall be 6 lumens, On-Axis Candela per node 2.3 cd/m². Input Voltage 7.5 VDC. Fixture shall be a Class 2 LED product. Fixture housing shall be IP66-rated polycarbonate. Fixture shall have multiple lens options – clear flat and translucent dome. Optional marquee lenses available in clear, semi-frosted, and translucent. The LED system should be digitally driven using noise-shaping pulse width modulation (PWM) techniques, and use integral and differential nonlinear control. Fixture shall be able to receive an individual light address per node controllable via DMX 512 or Ethernet protocol, which is compatible with standard Ethernet hardware. The LED channels shall be RGB (Red / Green / Blue). The system should achieve a Power factor correction of at least 0.99 into every fixture. LED fixture and its interface shall be able to be controlled by manufacturer controller. Fixture technology shall allow interface and LED fixtures be connected by unified power/data cable to eliminate the need for extra data cables and accessories. Outdoor LED fixtures shall comply with Random Vibration MIL-STD 810 Category 24, pass temperature range operational testing from –40° C to 50° C, pass high-temperature operating testing up to 50° C, meet lumen maintenance standards as defined in IESNA LM-80-08, pass water ingress testing, and pass general endurance testing. LED fixture shall be CE certified, PSE marked, and FCC Class A compliant. Suitable factory made leader cable with waterproof connectors to be provided. Finish: white / Black basis of choice of Architect and end client.The fixture should be similar to Philips Color Kinetic iColor Flex MX 8" inch spacing(10 m strip ), 150 No of controle module, with power supply 300 no of spacer,flex SL ,4 inch ,white ,50 per bag 300 no of icolor ,flex leader,cable 25 ft and 1 No of LSM including labour and transportation charges etc.., complete

Supplying and fixing of LED OUTDOOR FITTINGS (LIGHT EMITTING DIODE) 80W LED Focus Light Fitting including cost of materials and labour charges

Supply and laying of 2 x 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. With etc.., complete..,

Supply 5 nos of ESE lightning conductor for providing protection radius of 131m, Model LAP AX 210, tested in accordance with NFC 17-102 for advance triggering time of 82 microseconds, short circuit test of 115KA, CE marked, temperature Withstand test of -40 to +120 degree Centigrade, Country of origin certificate, last inspection certificate, testable from external tester and carries 30 years replacement warranty from all defects 5nos GI mast with adaptor head raising LA from top of structure to be protected with fixing accessories,125 nos of 70 sq.mm. flexible copper cable for connecting LA with earthing and 10no of Maintenance free earth set consisting of copper bonded rod 17.2mm dia 10 ft long, 25kg earth enhancing chemical compound SABO-ERECON and clamp for connecting rod to cable / strip, FRP earth pit cover SABO PC2 including installation charges.(for 5 nos) With etc.., complete..,

supply of 8 no of 2 MP IP Bullet camera 30 m range and 1 No of 16 channel NVR 2 sata model ,H 265 Model 2 No of 4 TB hard disk 650 Meters of CAT 6 E cable PVC Round Conduit pipe with Required accessories 1 No of 4 U Wall mounted track 16 port POE Gigabyte switch 10/100/1000 ,& No of PVC 4x4 Inch camera back box ,36 Inch LED professional & commercial monitor with wall mounted stand ,24 inch LED monitor with wall mounted stand ,2 nod o Adjustable AND tiltable wall mounted stand ,1 no of KVA UPS with 30 M back up and installation ,Testing, commisioning charges and cable laying charges of CCTV.. With etc.., complete..,

Supplying and fixing of ESCALATOR Standards of EN115 Width of 1m and Horizontal steps 3NOS ,Vertical raise of 7500MM And Horizontal span of 18549MM Inclination of 30 degree and speed of 0.50 M/s and other technical specfication adopted as per commercial escalator standards. With etc.., complete..,

Structure: Base frame made out of SHS 72mm pipe as peripheral frame work and RHS 80 x 40mm pipe & SHS 40mm pipe as longitudinal and cross members welded as frame work. The top frame is made out of RHS 80 x 40mm pipe on periphery and SHS 40mm pipe as purline to support roof. The corner columns are made out of SHS 72 mm pipe. The entire structure is painted with 2 coats of zinc rich primer and 2 coats of enamel paint. Wall: The outer wall is made out of 50mm thick PUF insulated sandwich panels with TCT 0.35mm PPGL sheet as skin on both sides and core with 40Kg density self-extinguishing CFC free PUF by injection molding process. The PUF panels are provided at the back and half of the width on both LH & RH side. Towards front side of the cabin 1m from floor level is covered with sandwich panel, the next 1m as counter with glass and the remaining portion with PUF sandwich panel. The counter portion will have a door openable upwards to form a canopy for the counter. The front side of the cabin is provided with Powder coated aluminium framed glass door of size 6’ x 3’ and the remaining as fixed glass. The entire front portion is covered with rolling shutter with locking arrangement. Roof: The roof is made out of 30mm thick PUF sandwich panel of the same specification as wall except the thickness. The roof is rigidly fixed to the purline with suitable fasteners. The roof will have a projection of 1200mm at front side and 100mm on the LH & Rh sides. The roof is further cladded with 250 x 6mm thick polymeric panels on all the 3 sides except back side. The roof will have lifting hook arrangement at 4 corners to enable lifting the shell for transportation. Roof: The roof is made out of 30mm thick PUF sandwich panel of the same specification as wall except the thickness. The roof is rigidly fixed to the purline with suitable fasteners. The roof will have a projection of 1200mm at front side and 100mm on the LH & Rh sides. The roof is further cladded with 250 x 6mm thick polymeric panels on all the 3 sides except back side. The roof will have lifting hook arrangement at 4 corners to enable lifting the shell for transportation. Partition: The partition wall is made out of sandwich panel same as outer wall. The partition is provided with 1 door with locking arrangement. False ceiling: The false ceiling is made out of 250 x 6mm thick polymeric sections supported with GI grid. Cut outs are made to fix the light fixtures. Flooring: The flooring is made out of 19mm thick fibre cement board and finished with 2’ x 2’ Verified tile. Electricals: The cabin is provided with 1 no 2 x 36W - 2’ x 2’ recessed mirror optic fitting, 3 no’s 11W down light fitting, 2no’s 5A power point, 1 no A/C point, 1 no DB including necessary internal wiring using suitable sized FRLS wires.