Directorate Of Town Panchayats Tender

Vibrated Reinforced Cement Concrete 1:1.5:3 mix,(one part of cement, one and half part of M.sand and three part of aggregate) mix using 20mm ISS HBG metal from approved Quarry including cost and conveyance of all materials and all labour charges for mixing, laying, compacting and curing the concrete and other incidental charges to site etc., complete. as per standard specification 28 V,VI S25

Supply and fabrication of steel using TMT rods for all Reinforced cement concrete works including cost and conveyance of all materials and all labour charges for cutting, bending and placing the rod in position and tying up the rods with binding wire and other incidental charges etc., complete. as per standard specification SS 86 & 86A V,VI, VII (S6) 7,3

Supply and erection of steel centering, shuttering for soffits and sides including necessary support strutting for all RCC works using MS sheets of suitable size of BG 10 stiffened with MS angle of size 25x25x3mm for boarding laid over Silver Oak joists of size 10cmx6.5cm space at 10cm c/cand supported by Casurino Prop 10cm-13cm spaced at 75cm c/c etc., complete and as directed by Departmental Officers.

Column Surface

Plain Surface

Shuttering

Brick Work in Cement Mortor 1:5 Mix (one cement, five M.sand) using new best II Class Bricks of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications

Plastering in C.M. 1:3mix (one part of cement and three part of M.Sand) 10 mm tk including mixing and finishing to a well smoothened surface, watering cost and conveyance all materials and all labour and other incidental charges and other incidental charges etc., complete. as per standard specification TNBPSS 56,57

Plastering in C.M. 1:5 mix (one part of cement and five part of M.Sand) 12mm tk including mixing and finishing to a well smoothened surface, watering cost and conveyance all materials and all labour and other incidental charges and other incidental charges etc., complete. as per standard specification TNBPSS 56,57

Dadooing glazed tiles set in CM 1:2 mix(one part of cement and two part of M.Sand) of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Supplying and fixing over the floors best quality of Ceramic Tiles of size 305x 305 mm of approved colour laying with cement mortor 1:3 mix pointing the joints with colour pigments including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification .

Supplying and fixing in Position of Indian Oriya pan type water closet with “P’’ or “S’’ trap to set in brick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with CM. 1:3 mix 20mm thick without any leakage including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification .

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 12.50 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Supply and Fixing of Hand Wash Basin of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Supplying and fixing of PVC Door of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification .

Supplying and fixing over the floors best quality of Kota Stone of approved colour laying with cement mortor 1:3 mix pointing the joints with colour pigments including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification .

Weathering course with concrete of broken Brick jelly in pure slacked lime over roof slab the proportion of brick jelly to lime being 32 to 12.5 well beated with wooden beaters for giving required slope & thickness including cost and conveyance of all materials and labour charges and other incidental charges etc., complete as per standard specification

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outerframe 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

ALUMINIUM THREE TRACK WINDOW SIZE Supplying fabricating and fixing in position of Alumi,Anod natural colour matt finish sliding window in two track in all floors with following sizes . All the three shutters with sliding arrangemenst the bottom section shoulld have gutter arrangements so to drain the water entring and made with extruded aliuminium section for outer frames as shown below with necessary accessories such rubber beeding .,Necessary dismantling making necessary holes in RCC coloumns, Beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as drected by the dePart ofmental officers . The Aluminium surfaces should be anodised with matt finish under electrically condition in accordance with IS specification 1868/1962 of Anodic thickness of not less than 15 microns (fifteen) for all sections . All the materials should be got approved by the Engineer incharge before fixing as directed .

Supplying and fixing of Mild Steel Grill work of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A F.T. switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (For electronic regulator)(SD.No.24)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter lockingWall socket with 5A Flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD No.38)

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed power plug point (SD 40)

Supply and fixing of 4'40 W LED fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification (SD 88)

Supply and fixing of 32 Amps DP Switch of 500V with metal clad with fuse and neutral (Side Handle) on suitable TW Board with PWD Earthingincluding cost and conveyance of all materials to site and all labour charges etc complete asper std. specifications. (SD 143)

Supply and run of 4 x 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification (SD 68)

Supply and fixing of 1200 mm (48') AC Ceiling Fan complete with stepped electronic 300 W Regulator with 1 m down rod on existing Clamp of approved quality including cost and conveyance of all materials and labour charges and other incidental charges etc., complete as per standard specification (SD 107)

Painting two coats with Emulsion paint of approved colour and quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Painting two coats over new iron works with Enamel paint of approved colour and quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Supplying and fixing in position best Bevelled Edge MIRROR of 6mm thick of size 50cm x 40cm fibre glass shelf type with necessary plywood backing and rubber button, chromium plated screws, teakwood plugs, etc., complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Stainless Steel Handrails for Staircase using 50 mm dia 304 L Grade Stainless Steel pipe of 1.60 mm thick at requied locations to a height of 900 mm from finished floor level welded to 38 mm dia Stainless Steel pipe post of 1.00 mm thick as vertical at 900 mm centre with 2 Nos of 25 mm dia intermediate horizontal stainless steel pipe of 1.60 mm thick between. The vertical pipe has to be welded to the 100x 100x 6mm MS base plate encased in the base concrete. The rate inclusive of the charges for cutting, bending, welding,grinding, polishing, conveyance, electrical charges etc., complete. (Item No.M-0651)

Supplying and fixing over the floors best quality of Eurocon Tiles of approved colour laying with cement mortor 1:3 mix pointing the joints with colour pigments including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification .