Directorate Of Town Panchayats Tender

A. Plinth Beams

B. Beams and slabs

C. Columns

Supplying, fabricating and placing in position mild steel/Ribbed for steel roads for all RCC works including cost of steel and binding wire also in all floors, complete complying with standard specifications.

Providing and laying in position Standardised Concrete Mix M-30 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 400Kg/ cum and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards.

A. Up to basement

B. Super structure Ground floor

Brick work in cment mortar 1:5 (one cement and five sand) mix using second class chamber burnt bricks of size 9" x 4 3/8" x 2 3/4", including cost and conveyance of all other labour and material charges to site etc., complete complying with standard specifications.

A.for foundation and basement

B. For Ground Floor

Supplying and filling in foundation and basement and trenches with Filling M. Sand in layers of not more than 15cm thick well watered , rammed and consolidated complying with standard specifications etc., complete.

Supplying and filling in foundation and basement and trenches with Filling Well Gravel in layers of not more than 15cm thick well watered , rammed and consolidated complying with standard specifications etc., complete.

Special Ceiling Plastering and finishing all the RCC exposed surfaces such as RCC slabs, sunshades, conopies, staircase steps , etc., with cement mortar 1:3 (one cement three sand) mix to 10mm thick and including hacking the surfaces and providing necessary cement mortar nosing beading as per size, specification wherever necessary using the same mix as directed by the departmental officers etc., complete complying with standard specifications.

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Dadoing the walls with colour Glazed square tiles size 15cm x15cm x8mm of best approved quality in Cement mortar 1:2 ( one cement and two sand ) mix and pointing with the same colour cement neatly to full depth of tiles in all floors as directed by the departmental officer etc., complete complying with standard specifications.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Providing granolithic floor finish of 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed sand (M-Sand) and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 12.50 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in three track in all floors with following sizes. All the three shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish under electrically condition in accordance with ISI 1868/ 1962 specification for an average anodic film thick of not less than 15 microns. (All materials should be got approved by the Executive Engineer before fixing in position)

UPVC Ventilator.Specification:Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Manufacturing supplying and fixing of MILD STEEL DOOR made out of 50 x 50 x 6 mm M.S angle for outer frame,35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets (18 G) with 5Nos, of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers.

Supplying and fixing Supply and fixing of 50mm thick Anti Vibrating Rubber Pad including labour charges for fixing furniture fittings for windows & ventilators with standard drawings , etc., complete complying with standard specifications.

Supplying and fixing in position best Indian make white glazed earthenware WASH HAND BASIN of 560x406mm with a a pair of C.I. Brackets, 15mm dia C.P. Pillar tap, 32mm G.I. Waster water pipe, 32mm dia C.P. Brass waster coupling, plug with chain, 15mm dia PVC connection, 15mm G.M. wheel valve with ISI mark and necessary G.I. union and G.I. Elbow, including fixing wash hand basin in position with white lead, clamps, teakwood plugs, screws, rubber washer etc., complete without any leakage complying with standard specifications.

S/F in position of Indian Make White/Colour glazed earthen ware lipped mouth Flat Back Urinal of best approved quality with G.I.Pipe connection to suitable length,32mm bell mouthed P.V.C connection ,15mm dia G.M.Wheel valve,fixing the urinal to the wall in position with necessary T.W.plugs ,clamps,screws, shellac etc.,including dismantling masonry if necessary and redoing the same to original condition ,fixing the 15mm dia. G.I.pipe connection and wheel valve ,painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. - White Colour

Supply Deleivery of PVC and GI Pipe and Specials including cost and conveyance of all materials and all Charges Complete as per standard specification

Sanitary Pipe 110mm Dia Pipe

110mm Dia TEE

110MM Dia Elbow

110MM Dia Bend

40MM Dia UPVC Pipe

40MM Dia PVC Elbow

40MM Dia PVC TEE

40MM Dia Gate Valve

25MM Dia UPVC

20MM Dia Screw CroumiamTap

Wring with 2 x 1.5 sq.mm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with TW switch box and 5A F.T. switch in flush wall with 3mm Tk hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed Fan and light Point.(SD.NO:24)

Supply and fixing of 5A / 15A 3 pin combined flush type wall socket with 15A flush type switch on suitable TW box. Plug point( SD 136 )

Wiring with 2 x 4 Sq.mm (56/0.3) PVC insulated SC unsheathed Cu. Conductor cable of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC assosaries,in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3mm tk hylem sheet for 15 A 3 pin non interlocking CS plug with continious earth wire conection of 14 SWG TC wire, and making good of the concealed portion,with suitable colour for concealed Power Plug Point ( S.D.NO:39 )

Supply and run of 2 of 1.5 sq.mm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour. ( S.D. 54 )

Supply and run of 4 x 6 sqmm (56/0.3) PVC insulated SC unsheathed Cu,conductor of 1100V grade in 32mm dia GI pipe ( class "B") suitably bent at both ends with necessary angle iron up right and end supports for mains. (S.D.73)

Supply and run of 2 x 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V on 7/20 GI bearer wire for service connection mains. (S.D.65)

Supply and fixing of single box type 4"40W flu fittiing complete with copper choke and condensor with TW round blocks on wall or ceiling with PVC unshealthed copper leads from terminals to the fitting. (S.D.88)

Supply and fixing of WT bulk head fitting with guard (phillips/Bajaj/Crompton/K.Life) suitable for lamp with 11 W CFL bulb.(SD .83)

Supply and fixing of 1400 mm (56") /sweep AC ceiling fan complete with stepped 300W regulator, with the existing down rod on the existing clamps.(SD 108)

Supply and delivery and fixing of HDPE tank 1000 lit. as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and pecials for pipe connection works including cutting, threading and fixing charges etc.,

Painting iron works for doors, windows and ventilators, iron bars, weldmesh, wiremesh screen, steel bars , flats and other similar works etc., with Two coats of approved first quality of synthetic enamel paint over the existing red oxide primer in all floors it inclusive of cost of materials and labour, brushes and scaffolding etc., complete complying with standard specifications.

Painting two coats of newly plastered wall surface with ready mixed Cement paint of first quality and of approved colour over a priming coat including preparing the surface, clean removal of dirt and including necessary plaster of paris putty wherever required etc., complete complying with standard specification.