Directorate Of Town Panchayats Tender

Supplying and errecting centering for plane surfaces such as RCC slab,beam etc.,including strutting upto 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm for boarding laid over country wood (silver Oak) joists of size 10cm X 6.5cm spaced at 90cm centres and supported by casurina props of size 10 - 13cm dia spaced at 75cm centres including necessary cross bracings etc., complete complying with standard specifications.

Without strutting

With strutting

Reinforecement Cement concrete 1:11/2:3 ( one cement one and half part sand and three aggregate) using 20mm size hard broken granite stone jelly for plain concrete including cost of material machine for mixng motor, vibrating charges shoring, strutting and Dewatering wherever necessary laying in layers of 15cm thick consolidation and curing inclusife of all lead and lift etc., complete and as per directed by the departmental officers.

Supplying fabricating and placing in position of M.S or RTS rods including cutting, bending, placing and tying in position including cost of binding wire etc complete as per standard specification.

Brick work in Cement Mortar in 1:5 ( One cement and Five Sand ) using best quality of Country bricks of size 8¾x 4 ¼ x 2 ¾ including all cost of materials and labour charges including Curing charges etc., complete as per Standard Specificationand as directed by department officials.

Special Plastering with cement mortar 1:3 (One cement three sand) 10mm thick including cost and conveyance of materials to site and including all labour charges etc complete.

Plastering walls with cement mortar 1:5 (One cement five sand) 12mm thick in all floors and all exposed surfaces including cost and conveyance of materials to site and all labour charges,Curing etc completeand as directed by department officials..

Painting the new walls two coats over one coat of priming with best Cement paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers (S.l.No.359-A)

Supplying and fixing of push and pull type Roling shtter confirming to IS 6248/1979 and as amended from time to time. With ISI make of approved size and section using 18 gauge G.I.sheet.The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of Hood covers , transportation charges etc., and as directed by Engineer incharge.

Supplying, fabricating and fixing in position of mild steel door with single/double shutters using M.S angle of size 40 x 40 x 6mm for outer frames and 35 x 35 x 5mm for shutter frames, fully covered with M.S sheet of 18 gauge with M.S flat of size 32 x 6 mm for internal stiffners and one number of aldrop , two numbers of tower bolts, holdfasts, hinges, handles etc., including providing one coat of red oxide primer. The rates shall inclusive of cost of all materials labour charges for fixing the door in position by dismantling the masonry, concrete etc. and redoing the same to the original condition duly packed with concrete etc., complete.

Manufacturing, supplying and fixing in position steel Windows / Ventilators of the following types; outer frames and shutter frames shall be made out of steel sections confirming to IS.7452 / 1990 t of ‘Z’ section (F.7D) of size 25mm x 20mm x 3mm and mullions are made of (F4B) ‘J’ sections of size 46mm x 25mm x 3mm and sash bars shall be made of ‘T’ section (T2) of size 25mm x 22mm x 3mm. including providing handle cum latch with suitable open shall be left for its easy operation and adjustable wind stay of sufficient length shall be provided for each shutter and with necessary MS angle hold fasts welded to the outer frame and 12mm MS square guard bars shall be welded to the inner flat of the window at equal intervals not exceeding 100 mm spacing and welding 18G MS sheet for panes and including one coat of red oxide primer and charges for fixing in position including dismantling the masonry, concrete and redoing the same duly packed with concrete etc., complete and as directed by the departmental officers.

Window

Ventilator

Painting new iron works with two coats of approved quality and color of synthetic enamel paint over the existing red oxide primer in all floor etc., complete as per standard specification.

Providing GRANOLITHIC FINISH of the 40mm thick with PCC 1:2:4 (one cement, two sand and Four Jelly) using 10mm to 12 mm HBGS jelly etc., including cost and conveyance of all materials and labour charges etc complete. As per standard specification.

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour SD 53

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A F.T. switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (For electronic regulator) SD 22

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 mm x 100 mm x 113mm TW switch box in flush with wall with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point. SD 35

Supply and fixing of 32 Amps DP Switch of 500 V with metal clad with fuse and neutral120W on suitable TW Board , with earth connection only SD 138

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work SD 228

Supply and fixing of TNEB meter Board suitable for 32A Single Phase service connection with 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit. SD 121

Supply and fixing of Solar Street Light System with mounting structure & Pole (MNRE Specification) Description of item 2 x 11W CFL (Luminaire with 1 CFL Each). PV Module : 120W Battery. Capacity : 12V, 100AH