Directorate Of Town Panchayats Tender

Reinforced cement concrete 1:11/2:3 (one cement one and half sand and three aggregate) using 20mm size I.S.S. metal including cost conveyance of materials to site and all labour charges etc., mixing laying consolidating curring etc., but excluding cost of steel etc., complete as per standard specification as per TNDSS NO: 30 V,VI (S3) VII-3

Supplying and erecting steel centering for sides and soffits including supports and strutting upto 3.29 m height for plain surface as RCC slabs, rectangular tee (or) elbeams, lintel, bed block stair case waist slab, landing slab, etc., complete as per standard specification - 10m2 as per TNDSS & Morth specification No:30 & 36 (Plain surface)

Brick work in cement mortar 1:5 mix using (One cement and five sand) using best quality of III class Country bricks of size (8 3/4"x4 1/4"x 2 3/4") for foundation including curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification TNDSS specification No.31 & 31C.

Supplying and erecting steel centering for sides and soffits including supports and strutting upto 3.29 m height for plain surface as RCC slabs, rectangular tee (or) elbeams, lintel, bed block stair case waist slab, landing slab, etc., complete as per standard specification - 10m2 as per TNDSS & Morth specification No:30 & 36 (RCC work)

Supplying fabricating and fixing in position of Aluminium anodised natural colour matt finish door half glazed and half PLB board / fully 12mm thick PLB board / fully 5.5mm thick glazed door using rectangular Alu. Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, aluminium clips, best double action floor springs / door closer, handles, locks and glass including all materials, labour and power consumption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC columns, beams, or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc. complete. The aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than 15 microns for all sections. All the materials should be got approved by the Engineer-in-charge brfore fixing in position as directed.

Supplying and fixing in position of Aluminium anodised partition with 62 x 38 x 2m extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 0.90m hight the bottom and top panels should be covered with 12mm thick MDF PLB exterior grade and the middle panels should be fixed at 4mm thick clear glass with necessary glasing clips, rubber, beeding etc., including necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by departmental officers. The aluminium surfaces is to be anodised with matt finish under electrically controlled condition in accordance with ISI 1868/1962 specifications for an average anodic film thickness of not less than 15 microns. All materials should be got approved by the Executive Engineer before fixing in position.

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Supply and delivery of following PVC pipes and specials

110mm PVC pipe

110mm PVC Elbow

110mm PVC Bend

32mm PVC pipe

32mm PVC Elbow

25mm PVC pipe

25mm PVC Elbow

32mm PVC Bend

25mm PVC Bend

20mm PVC Tap

Supplying & Fixing in position of white glazed Indian type water closet with 'P' (or) 'S' trap and Orissa slope set in brick jelly cement concrete 1:4:8 100mm thick using 20mm thick brick jelly ISS gauge and finished to sludge out any leakage and defalut including cost of WC 'P' (or) 'S' trap and foot rest etc., complete

Supply and fixing of mild steel grill works for staircase handle etc including redoxide priming coat and cost of materials and all labour charges etc. complete.

Plastering in cement mortar 1:3 (one cement three sand) using 10mm thick including cost and conveyance of all materials and labour charges etc, complete as per standard specification. [MoRTH Specification: Clause:1000/1300]

Plastering in cement mortar 1:4 (one cement Four sand) using 12mm thick including cost and conveyance of all materials and labour charges etc, complete as per standard specification. [MoRTH Specification: Clause:1000/1300]

Supply and delivery of 1000 litre HDPE syntex tank

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point (for electronic regulator) (SD-24)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed Fan point (for electronic regulator) (SD-24)

Wiring with 2 x 1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu. conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, wtih 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5A 3 pin non inter locking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD 38)

Supply and fixing of single box type 4'40w flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting.(SD.88)

Supply and fixing of 8 way SP DB with 32A DP Switch with metal clad of 500V with fuse and neutral (side handle) on suitable TW Board with earth connection only (SD-158)

Supply and fixing of TNEB meter Board suitable for 32A Single Phase service connection with 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit. (SD-125)

Supply and run of 2 of 4 sq.mm (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7/20 GI bearer wire for service connection mains (SD-65)

Supply and fixing of RCC precast slab in cement concrete 1:2:4 mix ( One cement two sand four aggregate ) using 20mm ISS metal including cost of moulding charges mixing laying and curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification but excluding cost of rein forcement (100mm thick)

Floor Finishing First Quality Design Ceramic tiles of All colours of sizes 305mm x 305mm x 6mm. laid in cm 1:3 mix 10mm thick and pointing with white cement using 0.4kg/sqm including finishing the joint and pointing flush with tiles surface etc complete

Dadooing with glazed tiles of 300mm*200mm*6mm size of approved quality and colour set in c.m 1:2mix (one cement and two sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed -including cost of all materials and labour charges etc complete as per SS

White Porcelin Sink of size 600mm x 450mm x 200mm with 32mm dia 'B' Class G.I. waste water pipe and 32mm dia C.P. waste coupling.

Granolithic Floor finishing with Cement Concrete 1:2:4 (One part of cement, two parts of sand and four parts of ISS HBG metal) mix using 10mm to 12mm ISS size HBG metal to 25mm thick including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:39-F (20mm thick)

Painting two coats with ready mixed Plastic Emulsion Paint S.I.358 Plastic emulison paint of'approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:66-A (Sl.No.358)