Directorate Of Town Panchayats Tender

Vibrated Reinforced Cement Concrete 1:1.5:3 mix,(one part of cement, one and half part of sand and three part of aggregate) mix using 20mm ISS HBG metal from approved Quarry including cost and conveyance of all materials and all labour charges for mixing, laying, compacting and curing the concrete and other incidental charges to site etc., complete. as per standard specification 28 V,VI S25

Supply and fabrication of steel using TMT rods for all Reinforced cement concrete works including cost and conveyance of all materials and all labour charges for cutting, bending and placing the rod in position and tying up the rods with binding wire and other incidental charges etc., complete. as per standard specification SS 86 & 86A V,VI, VII (S6) 7,3

Supply and erection of steel centering, shuttering for soffits and sides including necessary support strutting for all RCC works using MS sheets of suitable size of BG 10 stiffened with MS angle of size 25x25x3mm for boarding laid over Silver Oak joists of size 10cmx6.5cm space at 10cm c/cand supported by Casurino Prop 10cm-13cm spaced at 75cm c/c etc., complete and as directed by Departmental Officers.

Column Surface

Plain Surface

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand) using new best II Class Bricks of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications

Plastering in C.M. 1:3mix (one part of cement and three part of Sand) 10 mm tk including mixing and finishing to a well smoothened surface, watering cost and conveyance all materials and all labour and other incidental charges and other incidental charges etc., complete. as per standard specification TNBPSS 56,57

Plastering in C.M. 1:5 mix (one part of cement and five part of Sand) 12mm tk including mixing and finishing to a well smoothened surface, watering cost and conveyance all materials and all labour and other incidental charges and other incidental charges etc., complete. as per standard specification TNBPSS 56,57

Finishing with top of roof with one course of machine pressed tiles of size 20cm x 20cm x 20cm of approved quality laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound conforming to ISS by 2% weight of cement used and the joint pointed neatly to full depth of tiles with same water proofing compound mixed with cement motar ,red oxide, including cost and conveyance of all materials and labour charges and other incidental charges etc., complete as per standard specification

Dadooing glazed tiles set in CM 1:2 mix(one part of cement and two part of Sand) of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Supplying and fixing over the floors best quality of Ceramic Tiles of size 305x 305 mm of approved colour laying with cement mortor 1:3 mix pointing the joints with colour pigments including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification .

Supplying and fixing in Position of Indian Oriya pan type water closet with “P’’ or “S’’ trap to set in brick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with c.m. 1:3 mix 20mm thick without any leakage including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification .

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 12.50 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricatedfrom un-plasticized polyvinyl chloride (uPVC) sections.Profiles: The profiles should be three chamber systemwhich provides high insulation properties with outerframe 60mm x 55mm with an outer wall thickness of2.4mm.The window unit should be designed with allcorner joints mitred and fusion welded. Windowsshould be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Supplying and fixing of Steel Door and Gate of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and M-Sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs fuel, labour and drilling bentonite and water required for drilling at site. Site will be shown by the TWAD Board officers including construction of mud pit.

Reaming 140/150 mm dia pilot bore to 300mm dia bore as directed by the TWAD Board Officer.

Supply of the following casing pipes of ISI approved quality with wall thickness not less than 7.5mm to 8.5mm with PVC couplers and cement Paste etc. Complete and including packing the annular space with pebbles quality and size of pebbles and the PVC pipe should be approved by the departmental officer..

150mm dia OD PVC Plain casing Pipe (CS)

150mm dia OD PVC slot casing Pipe (RS)

150mm dia OD PVC end cap

Labour Charges for inserting PVC Casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC Couplers with Cement paste etc., complete supply and packing the annular space with pebbles of size and quality as approved by the executive engineers TWAD Board

Charges for developing the borewell with air compressor of 300 cfm capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board officers and conducting yield test by 'V' notch method.

Supply and delivery of clear water vertical wet type submersible pump conforming to IS 8034/2002 and as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor suitable for operation in AC single phase 230 V+/- 10 %, 50 HZ +/- 5 % 20Lpmx60m

Supply and delivery of Single phase Panel Board 1HP with two level guard and auto start including all charges etc complete as per standard specification.

Labour charges for the erection of submersible pumpset 1HP in borewell/openwell including fixing and jointing submersible cable withproper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days.

Supply and Delivery and fixing of HDPE tank of 2000 litre capacity as per IS1 12701/1996 inculding,unloading,transportation and labour charges for fixing of the GI pipes and Specials for Pipe connection works Inculding cutting,threading and Fixing charges etc., Complete

Supply and delivery of GI pipes and specials approved quality including cost and conveyance of all materials and all labour charges and other incidental charges to site etc., complete. as per standard specification

32 mm UPVC Pipe

32 mmUPVC cupling

32 mm UPVC ElBow

32 mm UPVC Union

32 mm GM Gatevalve

32 mm NR valve

32 mm Hex Nipple

20mm Waste Not Tap

110 mm PVC Pipe

110 mm PVC Elbow

110 mm PVC TEE

2.5 Sqmm 3 core Flat Cable

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A F.T. switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (For electronic regulator)(SD.No.24)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter lockingWall socket with 5A Flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD No.38)

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification (SD 88)

Supply and fixing of 32 Amps DP Switch of 500V with metal clad with fuse and neutral (Side Handle) on suitable TW Board with PWD Earthingincluding cost and conveyance of all materials to site and all labour charges etc complete asper std. specifications. (SD 143)

Supply and run of 2 of 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V on 7/20 GI bearer wire for service connection mains of approved quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification (SD 66)

Painting two coats with Emulsion paint of approved colour and quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Painting two coats with Enamel paint of approved colour and quality including cost and conveyance of all materials and labour charges and other incidental charges to site etc., complete. as per standard specification

Supplying and fixing in position best Indian make white glazed earthenware WASH HAND BASIN of 560x406mm with a a pair of C.I. Brackets, 15mm dia C.P. Pillar tap, 32mm G.I. Waster water pipe, 32mm dia C.P. Brass waster coupling, plug with chain, 15mm dia PVC connection, 15mm G.M. wheel valve with ISI mark and necessary G.I. union and G.I. Elbow, including fixing wash hand basin in position with white lead, clamps, teakwood plugs, screws, rubber washer etc., complete without any leakage complying with standard specifications.

Supplying and fixing in position best Bevelled Edge MIRROR of 6mm thick of size 50cm x 40cm fibre glass shelf type with necessary plywood backing and rubber button, chromium plated screws, teakwood plugs, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position of Incenerator of approved make etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position of Stainless steel Pipe of approved make etc., complete complying with standard specification and as directed by the departmental officers.