Directorate Of Town Panchayats Tender

Supplying and erecting, centering for sides and soffits including supports and strutting upto 3.29m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheet of 90cm x60cm BG 10 gauge stiffened with welded M.S. angle of 25 x 25 x 3mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10 cm to 13 cm dia spaced at not less than 75 cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specification. (The payment for centering shall be made only after the concrete is laid. The retrieved materials should be taken back by the contractor) a) For Column footing and Plinth Beam

a) For Column

b) For Lintel,Roof Beam and Roof

Supplying, fabricating and placing in position M.S. or R.T.S. reinforcements grill for RCC works as per the design given including cost of steel and binding wire etc., complete complying with standard specification. (The contractor will have to make his own arrangements for the supply of M.S. plain rods / RTS rods and binding wire)

Providing and laying in position Standardised concrete mix M-20 Grade in accordance with IS:456 ,2000 using20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55,Including admixture (plasticiser/super plasticiser ) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete.improve workability without impairing strength and durability with about (5 cu.m) 7730 kg , of 20mm machine crushed stone jelly and without (3.3 cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m )7670 kg ,of sand,but excluding cost of reinforcement grill and fabricating charges centering and shuttering and also including laying ,vibrating with mechanical vibrators,finishing,curing etc.and providing fixtures like fan clamps in the RCC floor/roof slabs wherever necessary without claiming extra etc.complete complying with standard specification and as directed by the departmental officers.The coarse and fine aggregates to be used should comply with the requirements of IS standards,(No separate payment will be made by the Department for the excess usage of materials). a) Below GL

b) Above Basement (Ground floor)

c) 1st Floor RCC

d) 2nd Floor RCC

Reinforced Cement Concrete 1:8:16 Mix (One part cement, eight part sand and sixteen part of aggregate)using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing but excluding cost of reinforcement etc. Complete with std. Specifications as per TNDSS NO: 30 V, VI (S3), VII-3.

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand) using new best county Bricks II of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications a) Brick work Below Basement

b) Brick work Ground Floor

c) 1st floor Brickwork

d) 2nd floor Brickwork

Special ceiling Plastering in Cement Mortor 1:3 Mix (one Cement, Three sand) 10mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12 mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing M.S. Grill Door, Ventilator of approved design and as directed by the departmental officers including cost of MS Ventilator, labour charges and cost of one coat of red oxide primer with labour charges for priming coat etc. complete complying with standard specification.

Supplying and fixing of push and pull type Rolling shutter confirming to IS 6248/1979 and as amended from time to time. With ISI make of approved size and section using 18 gauge G.I.sheet.The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of Hood covers , transportation charges etc., and as directed by Engineer incharge.( SOR 132A)

Supplying and Fixing Teak wood Door panelled shutter with frame for door Fully panelled with 50mm Thick T.W. planks the door shutter Styles will be 75mm x40mm & Top rail 100 mm x40mm the lock rail will be of 125mm x40mm and the bottom raill will be 150mm x40mm and including cost of furniture fittings and cost of wind appliances and Labour charges for fixing Furniture etc and fixing up shutters in position and best french (Lac) polishing with two coats . T.W. doors windows ventilator including cleaning the surface etc., complete complying with standard specifications .

Teak Wood frames including wrought and put up for frames of doors windows and ventilators and other similar joinery works including providing Iron hold fasts and fixing the frame in position and dismantling the masonry for fixing the hold fasts and redoing the masonry etc . Complete complying with standard specification

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Paving the floor with descrigned coloured Vertified tiles of size 600 x 600 x 8mm of best quality and approved variety complying / confirming ISI specification land over cement mortar 1:3 (one cement and three sand) 20mm thick and pomted with same coloured cement neatly etc., complete.

Weathering course concrete using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime the proportion of brick jelly to lime being 32:12-1/2 by volume and laid over the RCC roof slab in a single layer and consolidated to the required finished thickness by beating the concrete with wooden, beaters of approved pattern keeping the surface constantly wet by sprinkling jaggery and lime water etc. complete complying with standard specification.

Finishing the top of roof with one course of approved first quality Machine Pressed Tiles of size 230mm x 230mm x 20mm thick of approved quality laid in Cement Mortar 1:3 (one cement and three sand) 12mm thick mixed with water proofing compound conforming to Indian standard as approved by the departmental officers at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same mortar mixed with the water proofing compound and red oxide etc. complete complying with standard specification.

Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality without priming coat including the cost all materials etc., complete, in all floors.

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Laying with Anti skid tiles (Colour and Shad as Directed) of size 305mm X 305mm X 6mm (Like Dora tiles Eurocon tiles etc),(anti skid) of 20mm thick of approved spl quality and set in Cement Mortar 1:3 (1 of cement and 3 of sand ) 20mm. Thick using river sand and pointing with colour cement using at the rate of 0.40 kg/M2 and mixing with colour pigment at the rate of 0.3 Kg/M2 including finishing complete with Standard Specification and as directed by the Departmental Officers etc.,

Dadooing walls with glazed tiles of size 300mm X 450mm X8mm size of approved make and quality and colour 1set in cement morter 1:2 ( one cement two sand) over 10mm base layer plastering and pointing with white cement neatly as directed

Supplying and fixing in position best approved quality and make white glazed earthen ware oriya type Indian water closet of size 580 mm with P or S trap embedding the closet and trap to shape in position with brick jelly lime concrete 1:2:5 (one lime two sand and five brick jelly) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the PVC soil stacks using 600mm length of 100mm dia CI pipe by dismantling masonry, RCC roof or floor slabs and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications (The water closet P or S trap are to be got approved by the Executive Engineer before use on works)

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 12.50 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) (SD23)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point SD 38

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed power plug point SD 40

supply and fixing of 18W LED square type Recessed fitting with LED (Lower end) on false Ceiling withsuitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. SD 529

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp. (SD 106)

Earthing as per the ISI Specification with an earth electrode of 2.1mt class 'b' GI pipe of dia not less than 40mm, with coper earth plate of size 125mm X 50mm X6mm, with necessary funneling arrangement with necessary masonry work and with 38mm RCC cover slab fsor the brick masonry (SD No: 233)

Supply and fixing of TNEB Meter Board suitble for 3phase 100A service connection made up of suitable angle iron frme of size 2feet X 1 1/2 feet using angle iron 1 1/2" X 1 1/2" X 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet X 1 1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 100 A fuse units (500V) 1 no. Neutral link, copper earth flat of size 1" X 1/4" with inter connection of EB meter to fues units by 7/16 PVC insulated copper wire with earth connection eomplete (SD 130)

Supply and run of 4 x 6 sq.mm. (56Nos/0.3mm.Dia) PVC insulated single core unsheathed copper conductor cable of 1100 V on 7/20 G.I. bearer wire for service connection mains (SD 68)

Supply and run of 4 x 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in 32mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains (SD-73)

Rubberised Interlocking Paver Block M40 grade providing and laying of 83mm thick heigh strength type confiriming IS 15658 - 2006 of Rubberised Interlocking Paver Block in required size of mininmum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flumying bore pattern with approved nin - sticking surface in the top and the rate including levelling the base cushion 150mm thick laying out the pavement cut the pieus to fit edge, vibrating pavers, sweeping transporting leading unloading as per standard specification.