Directorate Of Town Panchayats Tender

FOR COLUMNS

FOR GRADE BEAMS & FOOTINGS

FOR ROOF SLABS

Supplying fabricating and placing in position of RTS steel rods for reinforcement including the cost of steel and binding wire etc., complete and as directed by Departmental officers.

Reinforced cement concrete 1:1.5:3 Mix using 20mm size 1SS HBG grade machine crushed metal and excluding the cost of reinforcement and centring works and including the cost :of mixing laying curing etc complete complying with standard specifications.

Plastering in Cement Mortor 1:3 Mix (one cement, three sand )10mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand ) using new best II class Bricks of size 9 x 41/2 x 3 from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.

Plastering in Cement Mortor 1:5 Mix (one cement, five sand ) 12 mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.

Plastering in Cement Mortor 1:5 Mix (one cement, five sand ) 20 mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.

Supplying and fixing of M.S.grill Tress with Purlion of approved design for MS Pipe using necessary mild steel flats for inner and outer members which should be fixed to frames inclusive of priming coat of best approved quality red oxide primer etc., complete complying with standared specifications.

Painting two coats ready mixed Approved Exterior Emulsion of first quality and of approved colour over a primingcoat including through scarbing clan removel ofone coat of priming with best Cement paint as directed by the department officers etc complete and including necessary plaster of paris whever regd.(S.l.No.358) -10sqm complete. as per std., specifications.

Painting two coats new iron work for grills, with two coat synthetic enamel paint and approved quality and colour including priming coat . The rate is inclusive of cost of all materials, labour brushes and scaffolding charges etc., complete complying with standard specifications.

Floor finishing with ceramic tilles using best quality of ceramic tiles of size 30cm x30cm x 6mm over the base Plastering cement mortar 1:3 mix, 20mm thick pointing with Using white cement 4kg/10m2 including cost and conveyance of all Materials and all abour charges etc., complete:-

Dadooing the walls with best approved quality colour glazed tiles of size 200 x 200 x 6mm set in CM 1:2 (One of cement and two of sand) 10mm thick and pointing with colour cement using 0.4kg per m2 neatly in all floors as directed etc., complete complying with standard specifications.

Plastering in Cement Mortor 1:3 Mix (one cement, three sand )20mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.

Supply and fixing in position EWC type Colour water closet includes "P" (or) "S" trap including cost and conveyance of all materials to site and all labour charges etc., to complete as per std.,specifications.

Supply and fixing in position 22" Indian type water closet with foot reset includes "P" (or) "S" trap including cost and conveyance of all materials to site and all labour charges etc., to complete as per std.,specifications.

Supplying and fixing in position best Indian make white glazed earthenware WASH HAND BASIN of 560x406mm with a a pair of C.I. Brackets, 15mm dia C.P. Pillar tap, 32mm G.I. Waster water pipe, 32mm dia C.P. Brass waster coupling, plug with chain, 15mm dia PVC connection, 15mm G.M. wheel valve with ISI mark and necessary G.I. union and G.I. Elbow, including fixing wash hand basin in position with white lead, clamps, teakwood plugs, screws, rubber washer etc., complete without any leakage complying with standard specifications.

Supply and delivery of PVC and GI Pipe including cost and conveyance of all materials to site and all labour charges etc.as per standard specification. ( Excluding Pipe Laying Labour charges )g

50mm dia pvc pipe 10kg/cm3

63mm dia pvc pipe 6kg/cm4

90mm dia pvc pipe 6kg/cm6

110mm dia pvc pipe 6kg/cm7

Laying and jointing of PVC and GI Pipes including cost and conveyance of all materials to site and fixing all labour charges etc. complete as per standard specification.( Excluding Pipe Cost )

50 mm to 75 mm dia pvc pipes

90 mm to 110 mm dia pvc pipes

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in 25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron upright and end supports for mains [ SD NO. 70 ]

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour [ SD NO. 63 ]

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit [SD NO. 125]

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light / fan Point (for electronic regulator) (5 points per coil) [ SD NO. 21 ]

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting with tube [SD 89 ]

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL. SD-83

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.(SOR Item no.268,P.No.65)

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Ventilator: Providing and fixing casement Ventilator: fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.(SOR Item no.270,P.No.66)

Random Rubble masonry in Cement Mortor 1:5 Mix (one cement, five sand ) using new best rough and bond stones from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications.

Supply and delivery and Fixing of HDPE tank 1000 Lts.Capacity As per Is 12701 / 1996 inculingloading , unloading , transportation cost and conveyance of all materials and all labour charges. etc., complete

Supply and filling with 40mm size brick jelly including cost and conveyance and all materials to site and all labour charges etc., complete.