Directorate Of Town Panchayats Tender

Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items.(RCC floor slab, roof slab, Rectangular/ square, Tee/ Ell beams, Lintels, staircase waist slabs, Landing slabs, Landing beam, Portico beam etc., ).

Plain Cement concrete 1:2:4 (One cement Two M-Sand Four aggregates) mix using 20mm gauge hard granite broken stone jelly for bed blocks including cost and conveyance of materials to site and all labour charges etc complete with standard specification.

Supplying and fixing RCC Pre cast slab in RCC 1:1 1/2:3 mix including cost of reinforcement grill of the following 75 mm thickness in position but including moulding finishing, curing, and fixing them in position etc., complete complying with standard specification.

Plastering with Cement Mortar 1:5 mix.12mm thick including cost and conveyance all materials and all labour and other incidental charges and other incidental charges etc., complete. as per standard specification.

Collection and Supply of 40 mm Metal of approved quality including cost and conveyance all materials and all labour and other incidental charges and other incidental charges etc., complete. as per standard specification.

Collection and Supply of 20 mm Metal of approved quality including cost and conveyance all materials and all labour and other incidental charges and other incidental charges etc., complete. as per standard specification.

Brick work in Cement Mortar in 1:5 ( One cement and Five M-Sand ) using best quality of Country bricks of size 8¾x 4 ¼ x 2 ¾ including all cost of materials and labour charges including Curing charges etc., complete as per Standard Specificationand as directed by department officials.

Plastering walls with cement mortar 1:5 (One cement five M-Sand) 12mm thick in all floors and all exposed surfaces including cost and conveyance of materials to site and all labour charges,Curing etc complete as per standard specification.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm dia brass chromium plated piller tap, 32 mm dia C.P. waste coupling, 32 mm dia P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications (the wash hand basin and specials should be got approved by the Executive Engineer before use on works)

Weathering course in Brick jelly and lime concrete using broken brick jelly of size 20 mm uniform gauge in pure slacked lime ( no M-Sand to be used ) the proportion of brick jelly to lime being 32:12.5 by volume laid over the RCC roof slab in a single layer of required design , slope and finished thickness by beating the concrete with wooden and beaters of approved pattern keeping the surface constantly wet by springing lime Jaggery water etc complete as per standard specification.

Finishing the top of Roof with one course of machine pressed tiles of size ( 23x23x2 cm ) approved quality in C.M. 1:3 - 12 mm thick mixed with water proofing compound confirming to IS @ 2 % by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc complete as per standard specification.

Supplying, fabricating and fixing in position of mild steel door with single/double shutters using M.S angle of size 40 x 40 x 6mm for outer frames and 35 x 35 x 5mm for shutter frames, fully covered with M.S sheet of 18 gauge with M.S flat of size 32 x 6 mm for internal stiffners and one number of aldrop , two numbers of tower bolts, holdfasts, hinges, handles etc., including providing one coat of red oxide primer. The rates shall inclusive of cost of all materials labour charges for fixing the door in position by dismantling the masonry, concrete etc. and redoing the same to the original condition duly packed with concrete etc., complete as per standard specification.

Manufacturing, supplying and fixing in position steel Windows / Ventilators of the following types; outer frames and shutter frames shall be made out of steel sections confirming to IS.7452 / 1990 t of ‘Z’ section (F.7D) of size 25mm x 20mm x 3mm and mullions are made of (F4B) ‘J’ sections of size 46mm x 25mm x 3mm and sash bars shall be made of ‘T’ section (T2) of size 25mm x 22mm x 3mm. including providing handle cum latch with suitable open shall be left for its easy operation and adjustable wind stay of sufficient length shall be provided for each shutter and with necessary MS angle hold fasts welded to the outer frame and 12mm MS square guard bars shall be welded to the inner flat of the window at equal intervals not exceeding 100 mm spacing and welding 18G MS sheet for panes and including one coat of red oxide primer and charges for fixing in position including dismantling the masonry, concrete and redoing the same duly packed with concrete etc., complete and as directed by the departmental officers. specification.

Supplying and fixing of M.S grill of approved design for doors, windows and ventilators using necessary mild steel flats for inner and outer memebers which should be fixed to window frames inclusive of priming coat of best approved quality red oxide primer etc., complete complying with standard specifications.

Supplying and fixing of rolling shutters shall be pull and push type (Mannually operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10G MS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC.unsheathed Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A F.T. switch with painting of suitable Colourfor open PVC light point / fan point (For electronic regulator) (5 points per coil)

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting.

AC Ceiling Fan complete 1200 mm (48") Sweep with 300mm Down Rod (without Regulator)

Supply and fixing of 32 Amps DPIC Switch of 500 V with metal clad with fuse and neutral (Side Handle) on suitable TW Board , with earth connection only SD 138

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and fixing of TNEB meter Board suitable for 32A Single Phase service connection with 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit.

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38

Painting the new walls two coats over one coat of priming with best Plastic Emultion paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by the department officers (S.l.No.359-A)

Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality – 10m2.

Fabricating supplying and fixing of pre painted galvanium iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.060 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supply and delivery of PVC,GI Pipes and Specials to a standard length Using ISI rate should inclusive of all taxes. etc., complete as per standard specification.

2000Lit HDPE Tank

90mm PVC Pipe

90mm PVC Bend

90mm PVC TEE

Clamp Set

75mm PVC Pipe

75mm PVC Bend

75mm PVC TEE