Central Leather Research Institute Tender

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 fine sand)

Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 Upto 5 mm depth and 5 mm width metre

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm(Make: "Armstrong") and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. Work includes providing and fixing of approved make fan hold clip alround each fan as per the requirement of site condition. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) (Make: "Armstrong Ultima / Knauf Ceiling Solutions"). Note: 1. Contractor should submit the Sample of each item / other associated materials used in this work for seeking approval by CLRI. 2. Contractor should submit Test certificate for false ceiling tiles to be submitted to CLRI upon material arrival of site and before commencement of work. 3. Contractor should submit Copy of Invoice and delivery challan to CLRI. 4. Safety netting arrangements should be made by the contractor before commencing the work. 5. Other safety arrangements as per safety parameters should be made by the contractor at site before commencing the work.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and paneling to be paid for separately) : For fixed portion powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and paneling to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 100 kg to 120 kg and door width from 701 mm to 1200 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on wall 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on wall 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on wall 32 mm nominal outer dia Pipes

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length. 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade : One or more coats on old work

French spirit polishing : Two or more coats on new works including a coat of wood filler

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 30 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 20 mm to 40 mm thick : Second class teak wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 5 mm thick float glass panes, including bright finished brass butt hinges of required size with necessary screws. Second class teak wood 30 mm thick shutters

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 75 mm

Providing and fixing aluminium Powder coated Hinges (minimum thickness of powder coating 50 micron) required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium Powder coated tower bolts (minimum thickness of powder coating 50 micron) required colour or shade with necessary screws etc. complete : 200x10mm

Providing and fixing aluminium Powder coated Handle (minimum thickness of powder coating 50 micron) required colour or shade with necessary screws etc. complete : 200 mm

Providing and fixing PVC floor Trap of Make: "Astral / Supreme / Ashirwad" Size:- 110mm, Socket Type:- "S", Length:- 278mm, Depth of outlet:- 110mm & Height of Trap-118mm with necessary concrete bedding in floors with necessary cutting, placing, etc., complete all as required and directed by the Engineer-In-Charge

Providing and fixing ABS grating with cockroch trap complete all as required and directed by the Engineer-in-charge.

Providing and fixing 25mm ball valve(Screwed) of make: "Zoloto" with bronze ball valve(Screwed) approved quality conforming IS:554 provided with full bore, two piece design, quarter turn lever operated with S.S. Forged brass hard chrome plated ball, PTFE seating and gland packing complete all as required and directed by the Engineer-in-Charge.

Providing and Fixing PVC - SWR pipes for sewer lines - Type :B of ISI: 13592 approved by CPWD specifications of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s, Cowl, Shoe etc., using joining ring with solutions for necessary scaffolding etc., complete with all lead and lift as directed by the Engineer-in-charge. PVC pipe. 75mm dia.

Providing and Fixing PVC - SWR pipes for sewer lines - Type :B of ISI: 13592 approved by CPWD specifications of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s, Cowl, Shoe etc., using joining ring with solutions for necessary scaffolding etc., complete with all lead and lift as directed by the Engineer-in-charge. PVC pipe. 110mm dia.

Providing and fixing 12mm thick Boiled water proof (BWP) grade plywood (Make: Centuryply or Greenply or Kitply) as per the required size and shape to suit site conditions with appropriate screws etc., miscellaneous work involved, etc., complete all as required in all heights, in all leads and lifts etc.; and as directed by Engineer-in-charge.

Filling the gap in between aluminium/ stone/ wood frame and chimneys, roof protection, roof panels, and wall panels work by providing polyurethane foam ( " Make -BOSS 333 ") of approved quality and direction of Engineer-in-charge complete,

Providing and fixing Stainless Steel (S.S 304 Grade) Turbo Air Ventilator 600mm dia.(+ or - 25mm) with mounting base work includes making surface preparation for existing Galvalume sheet roofing making necessary hole of size and shape to suit/match the site requirement. Fixing of mounting base safely with appropriate screws and filling the gaps with approved PU sealant complete in all heights, leads & lifts with complete miscellaneous repairs involved in the existing roofing system. Complete test checking for performance and leak testing the Turbo Air Ventilator after the Installation complete all as all required and directed by the Engineer-in-Charge. Dimension Details : Ventilator Diameter Throat Diameter - 610mm(+ or - 50mm) Ventilator Diameter Outer Diameter - 750mm (+ or - 50mm) Note: 1. Contractor should submit the Sample of each item / other associated materials used in this work for seeking approval by CLRI. 2. Contractor should submit Copy of Invoice and delivery challan to CLRI. 3. Safety netting arrangements should be made by the contractor before commencing the work. 4. Other safety arrangements as per safety parameters should be made by the contractor at site before commencing the work.

Repairs to Wooden Laboratory Working Table of size: Length 2.40m x Breadth 0.80m x Depth 0.80m ( Note : Size of the each exiting table varies + or - 50mm ) work includes the following : 1. Mechanized Scrapping of existing polishing all over the laboratory working table internally, externally, all over the table, etc., and final scrapping with appropriate sand papering to make surface smooth and free from all kinds of dust, rashes and the like etc., for making the surface preparation for polishing work externally and making surface preparation for enamel painting internally including ( Polishing and enamel painting will be paid seperately ). 2. Replacment of existing hinges with 75mm Brass Ball Bearing Heavy Duty Hinges for laboratory working table with necessary Heavy Brass Screws for hinges and ensuring the free opening and closing shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 04 or more nos.) 3. Replacement of existing Tower bolt with 75mm Brass Heavy Duty Tower Bolt for tower bolts and ensuring the free opening and closing of shutters of laboratory working table and other associated arrangements and repairs pertaining to this work complete. (Minimum 02 or more nos.). 4. Replacement of existing handles with 100mm Brass Heavy Duty handle with Heavy Brass Screws for handles of laboratory working table and ensuring the free opening and closing of shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 02 or more nos.). 5. Replacement of existing hasp and staple for pad lock with 75mm Brass Heavy Duty Hasp and Staple with Heavy Brass Screws for laboratory working table and ensuring the free opening and closing of shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 01 or more nos.). 6. Replacement of existing cupboard lock with suitable 75mm Brass Heavy Duty Cupboard Lock for matching the thickness of existing shutter of laboratory working table with necessary heavy duty brass screws and ensuring the free opening and closing of shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 01 or more nos.). 7.Reparing of existing wooden drawers by necessary scrapping, surface planning throughly ensuring the free movement of opening and closing operations and other associated arrangements and repairs pertaining to this work complete. 8. Other associated miscellaneous repair works such as replacement of paneling wood with second class teak wood wherever necessary, filling of wood with second class teak wood wherever necessary, filling of wood putty & other associated packing and filling materials related to wooden items and making good to the laboratory working table and other associated item and the like etc; complete. 9. Checking and ensuring of free functioning of all associated such as Hinges, Tower bolt , Handle, Hasp & Staple,cupboard lock, etc; to make user friendly arrangements complete for laboratory working table by applying necessary and appropriate oiling & greasing for ensuring the free lubrication and easy handling. Complete etc., all as required above in all leads and lifts with complete repairs to suit site conditions and with all kinds of necessary miscellaneous items etc; all required and directed by the Engineer-in-Charge. Note: All Hardware materials, screws & other associated accessories should be fixed strictly with prior approval of Engineer-in-Charge.

Repairs to Wooden Laboratory Working Table of size: Length 1.80m x Breadth 0.80m x Depth 0.90m ( Note : Size of the each exiting table varies + or - 50mm ) work includes the following : 1. Mechanized Scrapping of existing polishing all over the laboratory working table internally, externally, all over the table, etc., and final scrapping with appropriate sand papering to make surface smooth and free from all kinds of dust, rashes and the like etc., for making the surface preparation for polishing work externally and making surface preparation for enamel painting internally including ( Polishing and enamel painting will be paid seperately ). 2. Replacment of existing hinges with 75mm Brass Ball Bearing Heavy Duty Hinges for laboratory working table with necessary Heavy Brass Screws for hinges and ensuring the free opening and closing shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 08 or more nos.) 3. Replacement of existing Tower bolt with 75mm Brass Heavy Duty Tower Bolt for tower bolts and ensuring the free opening and closing of shutters of laboratory working table and other associated arrangements and repairs pertaining to this work complete. (Minimum 02 or more nos.). 4. Replacement of existing handles with 100mm Brass Heavy Duty handle with Heavy Brass Screws for handles of laboratory working table and ensuring the free opening and closing of shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 04 or more nos.). 5. Replacement of existing hasp and staple for pad lock with 75mm Brass Heavy Duty Hasp and Staple with Heavy Brass Screws for laboratory working table and ensuring the free opening and closing of shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 02 or more nos.). 6. Replacement of existing cupboard lock with suitable 75mm Brass Heavy Duty Cupboard Lock for matching the thickness of existing shutter of laboratory working table with necessary heavy duty brass screws and ensuring the free opening and closing of shutters and other associated arrangements and repairs pertaining to this work complete. (Minimum 02 or more nos.). 7.Reparing of existing wooden drawers by necessary scrapping, surface planning throughly ensuring the free movement of opening and closing operations and other associated arrangements and repairs pertaining to this work complete. 8. Other associated miscellaneous repair works such as replacement of paneling wood with second class teak wood wherever necessary, filling of wood with second class teak wood wherever necessary, filling of wood putty & other associated packing and filling materials related to wooden items and making good to the laboratory working table and other associated item and the like etc; complete. 9. Checking and ensuring of free functioning of all associated such as Hinges, Tower bolt , Handle, Hasp & Staple,cupboard lock, etc; to make user friendly arrangements complete for laboratory working table by applying necessary and appropriate oiling & greasing for ensuring the free lubrication and easy handling. Complete etc., all as required above in all leads and lifts with complete repairs to suit site conditions and with all kinds of necessary miscellaneous items etc; all required and directed by the Engineer-in-Charge. Note: All Hardware materials, screws & other associated accessories should be fixed strictly with prior approval of Engineer-in-Charge.

Electrical Part

POINT WIRING: Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medum class PVC conduit, with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Make: LEGRAND/ ANCHOR ROMA/ MK BLENZE.

CIRCUIT WIRING in Existing System: Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit/CMS as required. MAKE:FINOLEX/POLYCAB/Q-FLEX 3X2.5 sqmm

CIRCUIT WIRING in Existing System: Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit/CMS as required. MAKE:FINOLEX/POLYCAB/Q-FLEX 3x4 sqmm

ISOLATOR 100A: Supplying & fixing following rating, four pole,415V,Isolator in the existing MCB DB complete with connections, testing & commissioning etc. as required. MAKE: LEGRAND/L&T/HAVALLS

SINGLE POLE MCB FOR DB: Supplying and fixing 6 amps to 32 amps rating, 240 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. MAKE: LEGRAND/L&T/HAVALLS 6 amps to 32 amps Single pole

Double Pole MCB 32A: Supplying and fixing 32 amps rating, 240 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. MAKE: LEGRAND/L&T/HAVALLS 32A DOUBLE POLE

Triple Pole MCB 32A: Supplying and fixing 32 amps rating, 415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. MAKE: LEGRAND/L&T/HAVALLS 32A Triple Pole

END TERMINATION: Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed/XLPE copper coductor cable of 1.1 KV grade as required. MAKE: DOWELS/COMET

6 Pin 15A Socket Outlet: Supplying & fixing following modular socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. MAKE: MK/ANCHOR ROMA/LEGRAND

15A Switch: Supplying & fixing following modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required. MAKE: MK/ANCHOR ROMA/LEGRAND

2 Module box with cover: Supplying and fixing following size /modules,GI box along with modular base & cover plate for modular switches in recess etc.as required Make: Legrand/Anchor Roma/MK Blenze 2 Module box with cover plate

6 Module box with cover: Supplying and fixing following size /modules,GI box along with modular base & cover plate for modular switches in recess etc.as required Make: Legrand/Anchor Roma/MK Blenze 6 Module box with cover plate

3 Module box with cover: Supplying and fixing following size /modules,GI box along with modular base & cover plate for modular switches in recess etc.as required Make: Legrand/Anchor Roma/MK Blenze 3 Module box with cover plate

12 Module box with cover: Supplying and fixing following size /modules,GI box along with modular base & cover plate for modular switches in recess etc.as required Make: Legrand/Anchor Roma/MK Blenze 12 Module box with cover plate

4Way 3PH DB : Supplying and fixing following way, horizantal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator) MAKE: LEGRAND/L&T/HAVALLS 4 (4+12)way , Double door

8Way 3PH DB : Supplying and fixing following way, horizantal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator) MAKE: LEGRAND/L&T/HAVALLS 8 way , Double door

8Way SPN DB : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator) MAKE: LEGRAND/L&T/HAVALLS 8 way , Double door

Cable End Box : Supplying & fixing cable end box (loose wire box) suitable for following way triple pole & neutral. Sheet steel, MCB distribution board, 415V, on surface/recess, complete with testing and commissioning etc. as required MAKE: LEGRAND/L&T/HAVALLS For 4 way,Double door TPN MCBDB

Cable End Box : Supplying & fixing cable end box (loose wire box) suitable for following way triple pole & neutral. Sheet steel, MCB distribution board, 415V, on surface/recess, complete with testing and commissioning etc. as required MAKE: LEGRAND/L&T/HAVALLS For 8 way,Double door TPN MCBDB

Making Hole for 450mm Ex Fan:Making hole for installation of exhaust Ex fan of size upto 450mm sweep by demolishing brick work manually/by mechanical means including disposal of malba within 50metres lead as required.

Making good and finishing of the wall by plastering for installation of exhaust fan of size upto 450mm sweep as required.

Twin Cable: Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper conductor cable, in PVC sleeve of suitable size on the floor / wall, or side of the table/ door etc. as required. MAKE:FINOLEX/POLYCAB/Q-FLEX

Cable Laying on Wall : Laying and fixing of one number PVC insulated & PVC sheathed / XLPE power cable of 1.1 KV grade of upto 35sqmm size (clamped with 1mm thick saddle) on wall surface/recessed as required.

EARTH WIRE: Providing and laying earth connection from earth electrode with 4.00mm dia copper wire in 15mm dia G.I pipe from earth electrode including connection with copper thimble excavation and refilling as required.

2 Modular 16A MCB: Supplying and fixing 16 amps rating, 240 volts, "C" curve, modular miniature circuit breaker suitable for inductive load of following poles in the existing modular flus box including cover plate complete with connections,testing and commissioning etc. as required. MAKE: LEGRAND/L&T/HAVALLS 16A DOUBLE POLE MODULAR MCB

4 pole metal enclosure: Supplying and fixing four pole sheet steel enclosure on surface/recess existing MCB/ISOLATOR complete with connections, testing and commissioning etc. as required. MAKE: LEGRAND/L&T/HAVALLS

S/F CABLE MANAGER SYSTEM:Supplying and fixing of 105mm x 50mm size cable management system with all accessories(divider, end cab,bend,tee etc.) etc., as required Make: LEGRAND/MK/Havells

DLP MINI TRUNKING: Supplying and fixing of 32mm x 12.5mm size DLP mini Trunking system including all accessories (end cab,bend,tee etc.)etc., as required. Make: Havalls/Legrand/MK

SUPPLYING AND FIXING OF EXHAUST FAN (450mm) : Supplying Installation and testing commissioning of 450mm Sweep Exhaust fan complete with all accessories.. etc, fixing in the existing hole / window grill and fixing accessories including connections with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc., as required (The rate inclusive of required louver etc.,) Make: Crompton / Orient / Havells/Almonard

A/C POINT: Supplying and fixing suitable size G.I/PVC flush box recess/surface with modurlar plate and cover including 32A modular MCB and fixing 25A modular socket outlet including connections, etc. as required. Make: Legrand/ MK Blenze/Havells

FOUR POLE 63A MCB: Supplying and fixing 63 A rating, 415 V, 25 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make:Legrand/L&T/Havells 63A FOUR POLE MCB

Potential Earth Electrode: Provision of copper Potential Earth Electrode type (Chemical earthing), 3mtrs, 1.5 inch dia with Augur / Drill / Bore a hole of 8 - 10 Inch in diameter to a suitable depth of 3 meters (Electrode Length). The work includes refilling the empty space around the Earthing Electrode with the 2 bags of moisture booster (compound /soil mix), each termination should be with suitable 2 set of stainless steel bolt, nut & flat & spring washers of each run, testing earth resistivity of the Electrode and provision of 2'x2'x1' brick & cement chamber with 2'x2' RCC cover and including painting,marking of value etc. as required. Make: Value Engineers/ Galaxy Earthing Electrodes.

SUPPLY AND LAYING OF 4 x 10 SQ MM, COPPER MV CABLE: Supply and laying of 4 x 10 sq mm copper PVC insulated, Sheathed and armored copper 1100 V grade UG cable on wall/roof/floor using suitable size clamps,screws and along the concrete floor/wall with necessory chipping pastering etc. The work also includes painting of wall, earthing,conforming to IS 1554 and submit with necessary test certificate etc. as required. etc.as required. Make: Finolex/Polycab/Havalls

REMOVING AND REFIXING OF CEILING FANS (With Suitable down rod) : Removing and refixing of, 1200mm sweep ceiling fan and includes supply & fixing of suitable existing truss/structure using suitable clamps/extra down rod and mounting arrangements etc., as required.

REMOVING AND REFIXING OF LED LIGHT FIXTURE IN FALSE CEILING: Removing of existing LED 2 X 2 Panel light and refixing of same light mounted on false ceiling/ recess with suitable metal angle clamps with metal hanging chain including connections with existing twin copper cable FRLS PVC insulated copper conductor etc., as required.