Indo Tibetan Border Police Tender

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with : Cement mortar 1:6 (1 Cement : 6 coarse sand)

Providing and fixing upto floor five level precast cement concrete solid block including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centring, shuttering and finishing smooth with 6mm thick cement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Centering and shutturing incl. strutting, proping etc and removal of form work for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shutturing incl. strutting, proping etc and removal of form work for Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.

Centering and shutturing incl. strutting, proping etc and removal of form work for Suspended floors, roofs, landings, balconies and access platform

Centering and shutturing incl. strutting, proping etc and removal of form work for Lintal, beam, plinth beam, girders bressumers and cantilevers

Centering and shutturing incl. strutting, proping etc and removal of form work for Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position machine batched and machine mixeddesign mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

Providing and laying in position machine batched and machine mixeddesign mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and fixing panelled or panelled and glazed shutters doors, windows and clerestory windows including ISI marked black enameled M.S. butt hinges with necessary screws (screws should be of stainlesss steel and brand Magnum/ Nettlefold/Amul) excluding, panelling which will be paid for seperately (Thickness of shutters should be 35mm) - first class local wood (Tita champa / Pine) conferming IS- 399:1963 (Weight of should be 545 Kg/ M3) Note- The shutters should be conferming IS 1003 (Part-2): 1994.Hollock wood. 35 mm thick shutterrs

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Kiln seasoned and chemically treated hollock wood

Providing and fixing glazed shutters for door, window and ventilatorsusing 4mm thick float glass pans of brand Modi float, Atul, Saint Gobain, golden only. Weight of glass pan should be 10.00 kg/sqm. Including black enamelled ISI mark Butt hinges with nessessury screws.(screws should be of stainlesss steel and brand Magnum/ Nettlefold/Amul). Kiln seasoned and chemically treated hollock wood. 35 mm thick shutterrs

Providing and fixing 35 mm thick wire gauge shutters using galvanized MS wire gauge of avarage width of aperture 1.4mm with wire of dia 0.83mm for door, window and ventilator Including black enamelled ISI mark Butt hinges with nessessury screws.(screws should be of stainlesss steel and brand Magnum/ Nettlefold/Amul). Kiln seasoned and chemically treated hollock wood. 35 mm thick shutterrs

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Steel work in built up tubular trusses including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. Hot finished welded MS SQ Pipe

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down(2" or 3" or 6" ) as specified

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat. Ridges plain (500 - 600mm).

Providing and fixing GI pipe midium class make with GI fitting of Unik and intillo techsupport clamp U-clamp of size 23x1x2.5mm of chilly incl. cutting and making good the walls etc ( Internal work) Exposed on wall 20mm dia nominal bore.

12 mm cement plaster of mix : 1:6 (1 cement : 6 coarse sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primer.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sum over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sum).

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar. Size of Tile 50x50 cm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement@ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter- For drain

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper- for pump room

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-A

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required. 2x2.5 sqmm

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep. palnt room

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supply and fixing following rating double pole 240 volts, isolator in the existing MCB DB complete with connection, testing and commissioning etc. as required of brand Havells, Indocopp, Standerd, L&T. 40 Amp

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 1.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 2.5 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Design, Engineering, supplying, installation, testing and commissioning of 01 no. Sewage Treatment Plant (Make: Organic Solutions/Environment Technologies & Systems/Ecologic Waste Solutions/ Equivalent) based on Sustainable Microbial Advanced-Eco Reactor Technology (SMART) process with total effluent handling capacity of 75 KL per day Associated civil works (under civil contractor's scope) :- 1. The STP drawings submitted are preliminary. However, the successful civil contractor will be required to submit the Good For Construction (GFC) drawings based on Final Shop Drawings & P&ID verified by Sustainable Microbial Advanced-Eco Reactor Technology (SMART) technology providers Organic Solutions/ Environment Technologies & Systems/ Ecologic Waste Solutions/Equivalent or their verified licensees along with Detailed Process incorporating the working details. All the works shall be carried out as per approved "Good for Construction” drawings only. 2. Construction of Eq tank & Fermentative Reactor as per drawings submitted by the technology provider 3. Construction of Advance Eco Reactor (AER) as per drawings submitted by technology provider 4. Construction of Tertiary Treatment Stage & Treated water tank as per drawings submitted by technology provider 5. Construction of Bar Screen Chamber as per drawngs submitted by the technology provider 6. Construction of grease traps for all Mess/Kitchens as per drawings submitted the technology provider 7. Provision of River Gravels as per size suggested by the technology provider (Qty: 30 CUM) 8. All kinds of associated civil works Design Features: 1. The plant should be able to operate efficiently at 10% of design flow and should be suitable for low/peak flow. 2. The STP should be able to operate in continous, batch or intermittent mode as required. 3. There should be no daily/weekly/monthly sludge handling. 4. Civil Contractors along with the bid need to submit an MOU from the technology provider Organic Solutions/ Environment Technologies & Systems/ Ecologic Waste Solutions or their verified licencees for design, engineering, installation & commissioning of STP (capacity 75 KLD) based on Sustainable Microbial Advanced-Eco Reactor Technology (SMART) along with supply, activation & commissioning of AER media, bacteria dosing protocol etc. 5. The plant should not create any noise, with no nuisance of fly or mosquito. 6. STP to be operated in auto mode with supervision by operator once-twice daily. 7. The plant should work without the use of any mechanical aeration of any type. 8. The plant should be eco friendly. 9. Water recovery rate should be 90% of the sewage.

Supply, installation, testing & commissiong of SS Screen with SS Frame with suitable cleaning arrangement to block the in organics like bottles, glass, polythenes etc. Type: Bar Screen with 8mm to 12mm opening Make: SS 304 Fabricated

Supply, installation, testing & commissioning of Single stage, horizontal, centrifugal, Raw Sewage Pumps incorporating C.I. casing, CI impeller, CI motor body with level controller and MS pump frames. Discharge: approx 3750 Lit/hr (each) at upto 10 Meter head. Motor capacity: 1.0 HP (1W+1SB) (Pump Make : Wilo/Kirloskar/Crompton/Equivalent)

Supply, installation, testing & commissioning of Single stage, horizontal, centrifugal, AER Feed Pumps incorporating C.I. casing, CI impeller, CI motor body with level controller and MS pump frames. Discharge: approx 7500 Lit/hr (each) at upto 12 Meter head. Motor capacity: 1.0 HP (2W+1 SPARE) (Pump Make : Wilo/Kirloskar/Crompton)

Supply, installation, testing & commissioning of Organic AER Media to facilitate attached growth process in the Advanced-Eco Reactor. AER media should have the appropriate C:N ratio, microbial and mineral additives to facilitate bio-film formation in the attached growth process. Cost shall include provision of general arrangement scheme of the distrbution grid, air vents, pump flow rates, recirculation rates in accordance with HLR & OLR of Organic AER Media to ensure no choking/clogging of AER media due to sludge. (Approx Qty: 75 cum) Porosity : 40-60% C:N Ratio : 250-400 :1 Microbial Additive : Facultative strains in Powder form Mineral Additive: Silica, Lime Calium, Magnesium (Make: Organic Solutions/Environment Technologies & Systems/Ecologic Waste Solutions/Equivalent)

Supply, installation, testing & commissioning of Single stage, horizontal, centrifugal, Recirculation cum filter feed pumps incorporating C.I. casing, CI impeller, CI Motor body with level controller and MS pump frames. Discharge: 15000 Lit/hr (each) at 12 Meter head. Motor capacity: 1.5 HP (1W+1SB) (Pump Make : Wilo/Kirloskar/Crompton/Equivalent)

Supply, installation, testing & commissioning of Vertical Flow mounted mild steel Epoxy pressure type Activated Carbon Filter (fabricated from MS sheet of IS 2062 grade material) provided with an inlet distributor. The external of vessel to be painted (internally with epoxy primer) and to be filled with the required quantities of filer media like carbon, gravels, silica sand etc. Flow rate = 3.75 M3 / hr Height/Dia = 1800mm/600mm Shell / Dish thickness = 6mm/8mm Working pressure = 3 Kg/Sq.cm. Max pressure = 5 Kg/Sq.cm. Type of Carbon = Coal based Granular Activated Carbon IV 800. Min Carbon Qty: 150 Kg Make: (MS IS 2062 grade material fabricated)

Piping work for STP with all necessary accessories like B/F valves, Ball valves, suitable MS supports, Pressure gauges, MTA, Elbows, Unions, NRVs, reducer bush, FTA, clamps, GI nut bolts, rubber gaskets, couplers, suitable suction & delivery headers for pumps, couplers, foot valves, clamps, MS cable tray, fastners, cable ties, nipples, solvents, ball valves for bacteria preparation tanks, frontal & backwash piping for filter, air release piping for filter, multiport valves etc for making the STP & filtration system complete. (Pipe Make: Supreme/Prince/Astral; Type: PVC ISI Marked; Pressure: 10 Kg)

Supply, installation, testing & commissioning of Electrical Distribution Control Panel. The panel shall be made of 2mm thick CRCA sheet duly powder coated. The panel shall have necessary switch gears such as 64 amp MCB with outgoing switch gears for auto operation of raw sewage pumps, AER feed pumps, recirculation cum filter feed pumps, chlorination system, Treated water pumps with necessary MCBs, VIF meter, indication light, protection MCB and DOL Starter with MCB over load relay, single phase preventor relay, on-off light push button, auto -manual selector switch, cyclic timer for auto change over of pumps, dry run protection etc,. Control panel automation shall be as per the approved SMART technology providers specifications. (Construction of earthing pit, earthing from earthing pit to STP control panel, electrical connection from main line to STP panel & supply of treated water of pumps not under scope) Panel Make: Fabricated; Switchgears: L&T/Schneider/ABB/ Siemens/Equivalent.

Copper control wiring a) Copper unarmoured cable of suitable size in pvc channel/conduit/MS pipe from STP panel to all the pumps b) Copper submersible cable of suitable size from STP panel in PVC channel/Conduit/MS pipe for submersible sewage pumps

Supply, installation, testing & commissioning of Chlorine Dosing System consisting of 1 no. FRP/HDPE tank, 2 nos dosing pumps with a variable flow rate of 0-6 LPH, necessary polypropylene piping & injection fittings to make the system complete for dosing solution to the feed line. Pump Make: Edose/Acquanomic/Idose/Equivalent

Supply, installation, testing & commissioning of Single stage, horizontal, centrifugal, Treated Water Pumps incorporating C.I. casing, CI impeller, CI motor body with level controller and MS pump frames. Motor capacity: 1.5 HP (1W+1SB) (Pump Make : Wilo/Kirloskar/Crompton/Equivalent)

Providing of litres of probiotic microorganisms mother culture along with micronutrients for activation of probitoic microorganisms. (Bacteria Make: OS1/Envirosense/Ecolog) Manufacturer verified (signed & stamped) Material Safety Data Sheet (MSDS) of OS1/Envirosense/Ecolog microorganisms issued for this specific this work to be provided at the start of work.