Urban Improvement Trust Tender

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead as per Technical Specification Clause 301.5. with lead for 10 K.M.

Earth work in excavation including stacking/ disposal of surplus earth with all lifts and lead upto 1000 meters exclusive of compensation of earth (MoRTH specification Clause 301 to 305).mechanically by power shovel including mechanical loading and carriage upto 1 km by tipper/dumper

Providing and laying of interlocking concrete block pavements having thickness 100mm as per drawing and technical specifications.

Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricks Cement mortar 1 : 6 (1 cement : 6 coarse sand) 4 Chambers

Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured). Grading as per MoRTH specification : Table 400-1, 400-2 with CBR value not less than 25. ii)To achieve 95% Proctor density

Providing, laying, spreading and compacting crushed graded stone aggregate of as per table 400-10 and 400-11 to Wet Mix Macadam specification including premixing the material with water to OMC in mechnical mixer as per approved design mix, carriage of mixed material by Tipper to site, laying in uniform layers with motor grader/F.E. Loader/paver finisher in sub base / base course on a well prepared under base and compacting with vibratory roller to achieve the desired density including lighting, guarding, barricading and maintance of diversion etc. (MoRTH specification : Clause 406) by mechanical means with all lead

Random rubble dry stone kharanja under floor.

Construction of un-reinforced, without dowel bar, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 M30 (Grade), Coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholves, rakes, compacted using needle, screed and plate vibrators and finished in continous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 days, using curing compound and water finishing to lines and grade as per drawing and MoRD specification clause 1501 including vaccum dewatering process with all required equipments. Cement concrete M-40 grade

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering – All work up to plinth level. 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size).

Random Rubble stone masonry for foundation& plinth height above 30cm. thick walls in :CM 1:6.

Plaster on new surface on walls in cement sand mortar 1:4 including raking of joints etc. complete fine finish , 20 mm thick.

Providing and applying primer coat over prepared surface or granular base with bitumen emulsion as per IS: 8887 & manufacturer’s specifications @ 6 kg /10 sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures including cleaning of road surface as per MoRTH specification CIause- 502,112

Providing and applying tack coat with bitumen VG-10 on the prepared surface including cleaning as per IS : 8887 & manufacturer’s specifications @ 3 kg /10sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification CI.503,112

Providing and laying Dense Bituminous Macadam on prepared surface with specified graded crushed aggregates as per table 510 and design mix for base/binder course including loading of material with F.E loader, heating of binder (including cost of antistripping compound wherever required) aggregate and filler in hot mix plant 40-60 TPH transporting the mixed material by tippers and laying with sensor paver finisher as per clause 507.3.5 to the required level and grade, rolling by self propelled power rollers and vibratory rollers or pneumatic tyred roller 150-250KN. TP=0.7MPa to achieve the desired density (approved by the department) but excluding cost of primer/tack coat. [MoRTH Specification : Clause 507,112] with 4.50 % Bitumen with all lead. with CRMB - 60

Providing and laying bituminous concrete as per design mix on prepared surface with specified graded stone as per table 500 - 18 for wearing course including loading of aggregate with F.E. Loader and hot mixing of binder (including cost of anti-stripping compound, wherever required) and 3% cement filler with aggregates in hot mix plant 40-60 TPH Transporting the mix material with tipper to paver and laying with sensor paver finisher (as per clause 507.3.5) to the required level, grades and rolling with vibratory compactor and pneumatic tyred roller 150 - 250 KN, TP = 0.7 MPa, to achieve the desired density (approved by the department) excluding cost of primer/tack coat (MoRTH Specification : Clause -509,112) with all lead 30-45 mm compacted thickness with 6% binder grading - 2 with all lead of mix material a) With straight run bitumen grade 60/70

STEEL REINFORCEMENT: Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786). Thermo-mechanically Treated bars (Conforming of relevent IS code)

Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc.

Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. :- M20 Grade Nominal Mix (with graded stone aggregrate 20mm nominal size.).

Providing and laying of hot applied thermo plastic compound inclusive of type-1 reflectorising glass beads as per table 800.3, 800.4 applied in uniform thickness of at least 2.5 mm and spread uniformlywith reflectorising glass beads type-2 in addition @ 250 gm/scm with a road marking machine as per IRC : 35 complete with traffic diversion arrangement as per MoRTH specification clause 803.4.

Labour charges for refixing of Interlocking Block pavement i/c cost of bedding sand & water

Providing and laying Precast reinforced cement concrete Box culvert section of M-40 grade designed for 'AA' class loading as per IRC specifications including to effect of impact, EQ etc. complete on form base of 200mm thick lean concrete of M-10 grade with aggregate of size 40mm nominal of following internal size the work includes required safety measures construction of drain for diversion of flowing water cost of design of RCC Precast Box and its proof checking from IIT/MNIT Jaipur complete in all respect as per specifications. Size 1.00 M x 1.00 M

Supply of Retro-reflective sign boards size 1800x1200 mm made out of 2 mm thick aluminium sheet duly framed with 40 mm M.S. black tube (Medium Class) as per IS-1239 (Part-I) 1979 with Inner support of M.S. flat 12x3 mm whole structure is fixed with two supports each side 75 mm long and 40 mm M.S. black tube on two posts of 60 mm dia M.S. black tube (Medium class) as per 1239 (Part-I ) 1979 2.03 metre long each and also provision of hold fasts of M.S. bars 12 mm and 25 cm long two on each post. The sheet has to be stove enameled or epoxy painting one side and other side retro-reflective high intensity and black non reflective letter in non reflective sheet. The standard letters and numbrals have to be made as per IRC 30-1968 and the board shall be conformed to the MoRTH specifications clause. 801 Post and outer frame of board to be painted with black and white strips of synthetic enamel paint with black and white strips.

Supply of Retro - reflective Name Board size 600 x 900 mm made out of 2mm thick aluminium sheet fixed on post and frame made out or angle iron 50 x 50 x 6 mm, 3Mtr. long using stainless steel nut bolts of 8 mm dia, aluminium sheet is covered with high intensity grade Retro-reflective sheeting and non reflective letters in black, post duly painted in black and white synthetic enamel, complete in all respect. Confirming to MoRTH specifications clause. 801

Supply of Cat's Eye made of aluminium alloy size 75 x 100 x 22 mm having 21 bi-convex lenses embedded in circular disk of ABS plastic on each side.

Supply of "L" type Bollard made out of 1.25 mm thick M.S. sheet height 134 cm, welded in circular type ring section having upper dia. 15 cm and lower dia. 21 cm with another attachment of 15 x15 cm circular section with 15 cm face plate and hold fast at bottom, whole body is processed in white stoving enamel and red reflective 3 bands, each of 7.5 cm and one reflective sheet of 15 cm dia. provided to it complete in all respect.

Supplying and fixing solar road studs as directed by Engineer In charge at various places of minimum size ( 110 x90x30 mm) made out of aluminum alloys and poly carbonate, material having flat base with load bearing capacity of 20 tonne, within built rechargeable battery with 90 Hashes per minute Blinkers operation of Amber / red colour with automate dusk to dawn solar switching system with automatic battery having backup capacity for min 5 raining days, complete water proof visibility in normal climate should be 1000 m in normal night conditions and as per technical specification . Double sided Amber Colour

P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant.110 mm dia

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering – All work up to plinth level. M20 Grade Nominal Mix (with graded stone aggregrate 20mm nominal size.).

Providing, laying & fixing in position RCC spun or hume pipes ISI marked with proper jointing in required slope packed in the gasket of hume or spun yarn and neatly finished with rich grout of cement moratar 1:3 or having flexible rubber ring joint made with prefectly air and water tight including testing of joints as per MoRTH Specfication : Clause : 1000 & 2900 NP - 3 600 mm dia

Carriage of Meterial by mechanical transport Earth, sand, gravel, u/s kankar, lime, flyash, morrum, manure or sludge. For 5 K.M.

Providing and fixing of reinforced ferro-cement drain cover designed for class "AA" loading duly marked on cover with adequate steel reinforce- ment having thickness 75mm to 150 mm, anti-corrosive bitumen painted M.S. plate, rim and on M.S. lifting hooks, admixture like plastisizer bond-improving compound, shrinkage resistant compound, abrasion resistant complete as per approved design etc. 1500 x 600 mm (150 mm thick)

Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide

Painting with enamel paint of approved brand and manufacture to give and even shade. Two or more coats on new work.