Urban Improvement Trust Tender

Item Code [2022 3.1.1 M20]:Item Type [building] :: Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Item Code [2022 3.1.6]:Item Type [building] :: Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Item Code [2022 3.18]:Item Type [road] :: Construction of Subgrade and Earthen Shoulders (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2)

Item Code [2022 4.1 new]:Item Type [building] :: Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix

Item Code [2022 4.12 WMM 1110]:Item Type [road] :: Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.)

Item Code [2022 4.13.3]:Item Type [building] :: Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (Original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786)Thermo-mechanically Treated bars (Conforming of relevent IS code)

Item Code [2022 4.2 GSB-III]:Item Type [road] :: Sub Item Code [2022 4.2 GSB-III + iii]: Granular Sub-Base with Coarse Graded Material ( Table:- 400-2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) for grading-III Material

Item Code [2022 4.9 new]:Item Type [building] :: Centering and Shuttering with plywood or steel sheets including trutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc

Item Code [2022 5.1 i Primer coat]:Item Type [road] :: Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaningof road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 503 ( Low Porosity )

Item Code [2022 5.11 MSS]:Item Type [road] ::Sub Item Code [2022 5.11 MSS + (A) (i) b]: Close Graded Premix Surfacing/Mixed Seal Surfacing (Mechanical means using HMP of appropriate capacity not less than 75 tonnes/hour. Providing, laying and rolling of closegraded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.09 mm (Type - A) or 13.2 mm to 0.09 mm (Type- B ) aggregates using bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade.) Type A MSS (Aggregate 0.27 Cum / 10 Sqm , Bitumen 22 kg / 10 Sqm) Bitumen VG - 30

Item Code [2022 5.2 i tack coat ]:Item Type [building] :: Providing and applying tack coat with Bitumen emulsion (RS- 1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Item Code [2022 5.3 BM]:Item Type [road] ::Bituminous Macadam (Providing and laying bituminous macadam with 100-120 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder 3.3 %, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction) Sub Item Code [2022 5.3 BM + B (ii)]: Bituminous Macadam (Providing and laying bituminous macadam with 100-120 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder 3.3 %, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction) VG - 30 for Grading II (19 mm nominal size)

Item Code [2022 8.13]:Item Type [road] :: Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)