Urban Improvement Trust Tender

: Supply and installation of spike of M.S. rod 20mm dia 3.0mtr. long for earthing of (tower/pole) drive into earth by mechanical means sturcture connection the spike with cross arm top hamper PCC pole, lattics tower to earth etc. complete as per technical specification of DISCOM.

Supply & Laying following size B class, G.. Pipe confirming to 15: 1239 P-1 (2004) with accessories like bend, socket etc. for laying earth conductor/strip/ cable in ground/ surface/ recess as required. All as per pre approved by Engineer in charge. (Earth Excavation will be Paid Extra)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annex ure A attached with this bsr.40mm dia.

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR 3 x 1.5 sq.mm

:: P & F 4.5 mm thick M.S. traffic post with outer dia. 114.3mm, medium class and confirming to IS:1239(P-I) 5Mtr. Long (0.8 Mtr. Below ground level) suitable for fiber cap and M.S. base plate 300 mm x 300 mm x 6 mm including excavation of pit and grouting with P.C.C. of ratio 1:3:6 from bottom of the pole and up to 30 cm. above the ground level and 40 cm. dia. Including painting with rubber paint below ground level and red oxide on exposed surface and finishing with traffic yellow enamel paint in two coats compete as required.

Item Code [42.21]:Item Type [building] :: SITC of Crystal control Road warning Blinker system with solarpanel module with 300mm LED Module of minimum 190 Nos., Blinker Units, Charging circuit, suitable SMF Rechargeable Battery (12 Volt,), including wiring, connections etc. complete in all respect.

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR Single pole MCB (With B/C curve tripping Characteristics) , 6 A to 32 A rating

Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy =125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff AT=300 V AC and Auto resetting Safety , Power Factor 0.95 driver Efficiency 85% ,THD(I) 10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current 750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintained , CRI 70 and CCT 5700K +355K. Surge protection shall be min = 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR .LED Street Light fixture with Minimum lumen output 25000 lm

SITC of Automatic Street Light Control system with CCMS to schedule the timing of lights (Reprogrammed based on astronomical clock or on field or through central control), ON / OFF switch ( On field or centrally). connection type Three phase 18 Kw load, operating voltage 90-415Vac per phase L-N 50 Hz, maximum load handling capacity of 8 kVA per phase, supports LED Light. 24 Hours Li-ion battery back-up for communication, 220mAh coin cell for RTC. with earthing of panel and devices and 05 years comprehensive maintenance. Protective features with auto cut and auto recovery using threshold configuration for short circuit, over voltage. CCMS system to capture the energy usage and other parameters at predetermined interval and store data for 30 days, download data in field via mobile app or mobile dash board, system protection against surges, upgrade formway on field using a communication device via WIFI / GSM and GPRS low voltage / High Voltage Trip,Overload cutoff and operating voltage. Surge Protection: CAT B (6 kV/3 kA) ● Lamp Protection: 160 - 280Vac per phase L-N, 63A relay, 32A MCBs ● Monitoring: Voltage, current, power, power factor, energy, lamp hours ● Data Storage: 7 days history, 1-year report ● Timers: Scheduled and astronomical ● Switching: Remote and onsite ● Additional Features: GPS locator, event recording for supply and relay ON/OFF. MS sheet with two coats of enamel paint, duly hinged doors operable from both side with locking arrangement mounted on angle iron frame of size 35 mm x 35 mm x 3 mm having Panel Size-3.2mm Sheet(L)-600mm*(H)-1000mm*(D)-350mm.

Supply and erection of Decorative Pole Mild Steel with a total height of 9mtr above ground level with double arm bracket of street light 200W each side and predefined pattern in between the top portion of the pole. Pole bottom base section shall be shall be 400x200x1500mm, 4mm thickness column with two side predesigned laser cut to illuminate the surroundings in 20W with noticeable mode, next section embedded with double pole of 76x7000x3mm with golden casting embellishment with illuminated laser cut pattern design of bracket of 3000mm long to hold the street light. The base plate of pole shall be of sizeThe base plate of pole shall be of size 600x350x12mm. The Approximate weight of the pole is 165kg +-5%. Provision for inside termination box with 4way connector & 1nos 6 Amp MCB for local isolation. The pole and light fixture is primarily coated with primer, secondary epoxy resin and top coated with UV stabilized powder coat and cured. The decorative pole is suitable for outdoor lighting application. Pole light is complete in all aspects with all accessories and foundation bolts and Providing and Laying RCC Foundation work with TMT bars with Excavation of Pit n cement concrete of M-10 grade of 75 mm thickness,2 no. Required Size PLB HDPE Pipe and g Nosing Angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. Lugs on each face. The Neon flex strip is composed with Led in series jacketed by an inner plastic extrusion with IP 67 encapsulation in a 14mm tube. It is used to illuminate the overall laser cut pattern on pole of approximate size of 18mtr with 6W per mtr, color temperature 3000K, 12VDC driver. Led strip to be mounted with the help of clips.( as per attached drawing and Engineer Incharge )