Swami Keshwanand Rajasthan Agricultural University Tender

Taking out doors, windows and clearstory windows shutters (steel or wood) including stacking within 50 meters lead: Of area 3 square meter and below.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead.

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand) : Flush / Ruled/ Struck or weathered pointing.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: Old work (One or more coats) with lime including scrapping old surface and necessary repairs. Same colour

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 12 mm thick.

Half brick masonry with common burnt clay F.P.S.(Non Modular) bricks of class designation 10.0 in Superstructure , above plinth level upto floor five level Cement mortar 1 : 6 (1 cement : 6 coarse sand).

Pointing on stone slab ceiling with cement mortar 1:2 (1 cement : 2 fine sand): Flush/ Ruled pointing

Patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects.

Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc.

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead : With cement mortar 1 :4 ( 1 cement : 4 coarse sand)

Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges : Kota stone 25 to 30mm thick.

Providing and fixing horizontal chajja of Red/ White sand stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: New work(Two or more coats) including prepartion of base with primer, putty, lippy etc complete in all respect.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: One or more coats on old work including preparation of base with primer, putty, lippy etc. complete in all respect.

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect. On new work.

Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect. On old work.

Applying priming coat :With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on New Work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : One or more coats on Old Work

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches by sadal/loi. (Only for colour changing only.)

P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor

P & F water closet Seat Covers with brass hinges complete :Solid PVC (ISI marked) grade-I White for EWC.

Labour charges for removing W.C. pan (any type) of all sizes with care including all necessary fittings P or S trap.

P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall:PVC with PVC bend as per IS : 7231

P & F C.P. brass Doom Waste Coupling 32 mm dia.

P & F kitchen & Lab Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up to floor level complete including cutting and making good the wall & floor :White vitreous china laboratry sink600x450x200 mm

Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.Size 600 x 450mm x 4 mm thick

P & F Grating of approved quality/make:Stainless Steel Grating125 mm Nominal dia

P & F Jet spray for water closet with C.P. Copper Tube flange of approved make.

Providing & fixing C.P.flange for 15mm dia taps.

P & F G.I. Pipes with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors :-( Internal work ) Exposed on wall Medium Duty Pipes15 mm dia nominal bore

P & F G.I. Pipes with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors :-( Internal work ) Exposed on wall Medium Duty Pipes 25 mm dia nominal bore

P & F G.I. Pipes with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors :-( Internal work ) Concealed pipe in wall including painting with anticorrosive bitumen paint 15 mm dia nominal bore

P & F G.I. Pipes with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors :-( Internal work ) Concealed pipe in wall including painting with anticorrosive bitumen paint 25 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main including all fitting.Upto 25mm dia

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal bore.

P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15 mm Brass (IS:8931 marked).

P & F 15 mm. Dia Connection Pipe of approved quality/make : PVC pipe with C.P. Brass nuts upto length, 450 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. 75 mm dia. Type 'A'

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. 110 mm dia. Type 'A'

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single Bend without Door 87.5° 75 mm dia.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single Bend without Door 87.5° 110 mm dia.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Nahni Trap 100 x 75 mm

Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrial works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS: 694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's accessories (J.B., Bend etc.), round tiles,18 SWG G.I. box with earth terminal, 6 A switch, 3 pin ceiling rose/ Lamp holder/ 3 point connector, 3.0 mm thick ISI marked phenolic laminated sheet (IS: 2036 - 1995) Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. ass as per pre approved by Engineer Incharge, making connections, testing etc. complete as required for specification of copper conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05, & E - 07. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR., Short point (up to 3 mtr.)

Do-----------Medium point (up to 6 mtr.)

Do----------- Long point (up to 10 mtr.)

Wiring of 3/5 pin 6 amp. light plug point as per PWD specification for electrial works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS: 694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's accessories (J.B., Bend etc.), round tiles,18 SWG G.I. box with earth terminal of required size, 6 A switch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS: 2036 - 1995) Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. ass as per pre approved by Engineer Incharge, making connections, testing etc. complete as required for specification of copper conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05, & E - 07. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR., On Board.

S&F following sizes (dia.) of ISI marked MMS (IS : 9537 p-III) vergin material PVC conduit as per PWD specification for electrical works along with accessories (IS : 3419) as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL. accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge, for additional technical parameters of products/ work, refer Annexure "A" attached with this BSR MMS (IS : 9537 P-III) PVC conduit 20 mm

Do---------- PVC conduit 25 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical works with ISI marked (IS:694) and as per IS : 8130 : 2013 of 1.1 kV grade. Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss, oxygen free (10 ppm) for less chances of oxidization and higher silver content for gives better conductivity, insulation PVC type A, flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, in existing surface or recessed PVC/ MS conduit/ casing capping including all as per pre approved by Engineer Incharge, making connections, etc. as required OEM Must have its own in house NABL lab setup for all testing facilities for wires, For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR 2 x 1.5 Sq.mm.

Do-------------.2 x 2.5 sq. mm. + 1x1.5sqmm

Do----------- 2 x 4.0 sq. mm. + 1x 2.5sqmm

Supplying and fixing of power plug point accessories as per pwd specification for electric work on 18 SWG G.I. box of size 175 x 100 x 60 mm. with earthing terminal/ connector on surface or in recessed with suitable size phenolic laminated sheet IS : 2036-1995 cover including cost of 6 pin 16 amp. Switch and socket outlet , as per detailed in respective item on BSR making connection , testing , etc. as required all as per pre approved by engineer in charge For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR.

P&F of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, as per PWD specification for electrical works with ISI marked IS 8828 (1996)/ conforming to IEC 60898-1 2002, IEC 60947 -2, low watt losses, trip free mechanisum, energy limiting of class 3 as per IEC, minimum phase termination capacity of 35 sq.mm. conductorline load reversibility, label holding facility, IP-20 contact protection and fitted with existing distribution board/ sheets, min. peration 20,000 upto 32 A rating and 10,000 upto 63 A,, 5000 for 80 A rating including making connections, testing etc. as required. OEM shall have submit NABL/ CPRI/ ERDA accreduated lab test reports before execution & all as per approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A attached with this BSR. Single pole MCB 6 A to 32 A rating

Do--------- Double pole Isolator. 63 A rating

P&F of IK09 recessed/ surface mounting heavy duty horizontal type sheet steel of 1.6 mm thick Distribution board as per PWD specification for electrical works ISI marked conforming to IS - 13032 & IS-8623/ conforming to IEC 61439-3, Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link, neutral link, earth link, connecting wire of suitable rating and din bard, masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required OEM shall have submit NABL / CPRI/ ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR IP-43 Double door (Single phase) 8 way (8 O/G + 21/C)

P & F of ISI marked (IS : 3854) 6 amp. Flush type non modular switch as per PWD specification for electriical works, made out from industrial grade Polycarbonate or fire resistant ABS material, minimum width of switch toggle (PUSH PART) should not less then 18 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR

P & F of ISI marked (IS : 3854) 16 amp. Flush type non modular switch as per PWD specification for electriical works, made out from industrial grade Polycarbonate or fire resistant ABS material, minimum width of switch toggle should not less then 18 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR

P & F of 3 pin 6 amp. Flush type non modular socket as per PWD specification for electriical works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR

P & F of 3/6 pin 16 amp. Flush type non modular socket as per PWD specification for electriical works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR

P & F of ISI marked (IS : 371) 6 amp. surface type 3 pin ceiling rose as per PWD specification for electriical works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR

P & F of ISI marked (IS : 1258) 6 amp. Batten/ angle lamp holder as per PWD specification for electric works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required. All as per pre approved by Engineer in charge, for additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR.

P & F of non modular socket size flush type 120 watt rotary minimum 5 step fan regulator as per PWD specification for electric works, ISI marked (IS : 11037) made out from industrial grade Polycarbonate or fire resistant ABS material, including making connection testing etc. as required. All as per pre approved by Engineer in charge, for additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR.

P & F of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/ pole. Fixture made of powder coated single piece pressure die cast aluminium LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/ Toughened Glass cover (UV stablization report submitted for UV cover) and secondary lens on each LED & should be SMD type. The system level Luminaire efficacy =120 Im/ wt. with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with input voltage AC 120 to 270 V AC with High voltage Cutoff @=300 V AC and Auto resetting Safety, Input frequency 50 Hz+3% Power factor 0.95 driver Efficiency 85%, THD(I) 10% Humidity 10% to 90% RH working Temp. -5C to 45 C. driver current 1000mA shown in LM79 report. The luminaire shall be BIS certified and T.C. certified. Life Expectancy Equal or more than 50000 burnings hrs with Minimum 70% lumen maintened, color Rendering index 70 and CCT 5700 K + 355K. Surge protection shall be min 4 KV internal and min 10 KA external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark / Name Engrave/ Embossing on die cast housing to allow traceability/ authenticity. Fixture shall be as per IS 10322 complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/ LM80) Certificate/ report with liable warranty of product/ accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure 'A' attached with this BSR LED Street Light fixture 70 watt.