Rajasthan State Road Development And Construction Corporation Limited Tender

20 mm

25 mm

S&F following sizes of ISI marked ( IS:14927 P - II ) UPVC casing capping as per PWD specification for electrical Works along with all accessories like coupler, inner, outer, elbow, square box, tee, end cap etc. on surface with screws, expansion fasteners , All as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

20 mm x 12 mm

Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supply and Installation of unsheilded/ sheilded Information outlets made of high impact plastic body with ABS, FR Grade with provision for protection against dust in jack/ FP, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact punch termination on reliable copper tin plated Insulation displacement contact, It complied with ANSI/TIA/EIA 568 standard. In existing modular/MS Boxes along with necessory connections as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR.

Cat 6, Un-sheilded Information Outlet

Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture , material should be PC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions should be 86mm X 86mm as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Single Aperture

Supply, Installation, Testing and Comissioning of Rack mounted 19" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels (without I.O.) with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel, . There should be a provision for each port/jack on the panel and reusable removable on field from the panel complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors as per ANSI/TIA/EIA 568 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568, minimum requirement for 1G BASE-T/ 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, Minimum 750 to 1000 mating cycles in plug contacts for long durability complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR.

Cat 6, UTP (Un-sheilded Twisted Pair) Patch Cord

1 Mtr

2 Mtr

Supply, Installation, Testing and Commissioning of Wall mounted ISO 9001:2015 & 14001 or higher level certified company made Communication enclosure (Rack) of Minimum 500 MM Depth with made from CRCA & hot dip powder coated, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6 MM with 'U'Marking , with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19" angles with wall mounting provision on wall. Accessories like: 1 No of 19" 1U Horizontal Cable manager, 2 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19" 1U, mountable socket strips with 6 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with fastner of suitable capcity etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

15 U wall mounted Enclosure

Providing & Fixing of ISO certified company made vergin material PVC trunking system as per PWD specification for electrical Works, with double lock feature for cable management including finishing accessories like corners, tee, adjustable angles, junction etc. as required . The trunking system shall have adaptable system for modular type RJ 45 data socket/ wiring accessories/ power sockets and shall be covered with peal off plastic cover. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

32mm X 20mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( 10 ppm) for less chances of oxidization and higher silver content for gives better conductivity ,insulation PVC type A or C , flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

3 x 2.5 sq.mm

Supply , Installation, Testing and Comissioning of Managed Layer-2 Intelligent Giga Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports and with min 4 SFP Giga Ports (provision for Fiber Giga connectivity) with provision of minimum Stacking of 06 Switches with related LAN Base Software including making connections etc as required complete in all respect complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Non BSR

SITC of 160-260 V, 50 Hz ON-Line UPS with Isolation transformer suitable for single phase AC input and single phase AC output having enclosure degree of protection as per IS: 13947 Part-1/993/2004 complete with all protection and with SMF VRLA batteries, Charger, Switching Device etc and suitable trolley for batteries and UPS. Complete in all respect of following ratings.Approved Makes: Numeric, Eaton, Emerson, APC.

1KVA with 2 Nos 12V 65 AH Batteries

SITC of 55" Diagonal UHD (3840 x 2160) LED Display, 3 x HDMI Port, 1 x USB Port, 10 Watt Built in speaker, Panel technology: IPS or similar, Brightness 4000 cd/m2, Inbuilt media player-Unit should provide for inbuilt wifi & web browser & file sharing via url compatibility through IP, External Control-RS232C(in/out) thru stereo jack, RJ45, Response time- 8 ms; Contrast Ratio - 1100;1, refresh rate 60 Hz, viewing angle 178*178, operating hours: 16/7 or higher, internal processor: Quad core processor with signage OS, Internal memory: 8 gb or higher with Wall/Ceiling Mount; Safety & EMC Certifications- CE,FCC,UL,BIS; Approved Makes: Samsung, LG, Panasonic

SITC of 32" Diagonal Full HD (1920 x 1080) LED Display, 3 x HDMI Port, 1 x USB Port, 10 Watt Built in speaker, Panel technology: IPS or similar, Brightness 4000 cd/m2, Inbuilt media player-Unit should provide for inbuilt wifi & web browser & file sharing via url compatibility through IP, External Control-RS232C(in/out) thru stereo jack, RJ45, Response time- 8 ms; Contrast Ratio - 1100;1, refresh rate 60 Hz, viewing angle 178*178, operating hours: 16/7 or higher, internal processor: Quad core processor with signage OS, Internal memory: 8 gb or higher with Wall/Ceiling Mount; Safety & EMC Certifications- CE,FCC,UL,BIS; Approved Makes: Samsung, LG, Panasonic

SITC of Server PC With Processor Xeon E-2224 or higher, Minimum 4 Cores in Single Processor, 1 Threads per Core, Frequency : 3.4 GHz or higher, Memory: 16 GB or higher, DDR4 SDRAM or latest, Operating System : MS Windows Server 2019, LAN Onboard/ on slot Gigabit Ethernet (RJ45) , Hard disk drive: 2x 1TBSATA HDD, 7.2K, LFF, with 18" Monitor, Keyboard & Mouse (Approved Makes: HP/Dell/Lenovo)

SITC of Client Access License + Enterprise PC Player license: Technical description: Should Support Dual Channel, Support Interactive integration, Support Windows Streaming Video or live video inputs, 24 x 7 play back & Stable, reliable to with standing the load without any compromise in the performance. Should support Real time data integration feed without communicating Content management software; Capability of capturing live TV feed & Playback with inbuilt software module; Compatible with the Disgital Display system at Jaipur High Court Courtroom Informaton Dispaly Software to ebnable Advocates, Litigants and Court staff to be always be updated about the summery information of all the cases running in all the courts rooms through Local Display, NIC Web-site & NIC Mobile Application; The WebRTC based software solution must provide with separate login for each Court-master at the same time provide the flexibility to manage single/mutiple courtroom through the existing PC over the display Unit inside court room and the display units/Video Wall in corridors and common areas to display case number, item number, court room number, party names etc through Intergration with the NIC software to publish the case information on the NIC Website & the Mobile App through daily realtime auto data synchronization via APIs. The Court-master must be able to transfer court cases from one courtroom to another courtroom, manage & dispaly bulk case hearings, sharing of instant messages to all screens from any courtroom, to call an Item Number skip it or recall it, and to display the various notices and other important information Court want to display. The software to be compatible and integrated with the existing Court Room Information display software at the Rajasthan High Court Complex, Jaipur.as approved by Client department,compitant authority or site Engineer. Approved Makes: Staratacache/Scala/NEC or equivelent make.