Rajasthan State Road Development And Construction Corporation Limited Tender

Wheel Chair Overall size: 1120mm D x 670mm W x 920mm H approx. Tubular frame work of 22 mm OD x 18 G tube except for the four width wise stays of 19 mm OD x 18 G tubes For self-propulsion, two hoops of 15.8mm OD x 18 G SS tube mounted on rims of solid rubber tyre wheels of approx. 457 mm All MS parts should be pre-treated and powder coated.

Examination Couch with mattress 1. Constructed from round polished SS Pipes 2. Fully adjustable headrest. Top of Polished SS Sheet. 3. Legs fitted with thick high quality nylon gromets. 4. 4 inch 50PU density foam cushioned top covered with leathered Rexene of 2mm thickness 5. Top dimensions approx – L = 72inch X W=24inch Ht of – 32 inch 6. All the Stainless Steel should be seamless conforming to 304 grade/ 16 gauge and polished finished 7. Should have sliding foot step.

High Chair 1. High Rise chair revolving 2. High Back Chair shall be of dimensions – 500 mm W* 720mm D *1125mm H approximately 3. Seat shall be made up of 12 mm thick hot pressed anti- termite water resistant plywood, upholstered with leatherette/fabric and moulded polyurethane foam. 4. Chair back shall be made of 40 mm thick edge of PVC moulding with Mesh upholstery. The polyurethane foam density shall be 45 +/- 2kg/m3. Chair Back shall be fixed with lumber support & fixed with Head rest for extra support. Lumber support ( 150mm W * 150mm H ) attached leatherette/ fabric headrest shall be supported with 2 crome plated rods of 20mm thickness from headrest to seat base. 5. PU padded Adjustable handles (260 mm W * 85mm D ) shall operate through push button. Chair shall have regular tilt mechanism feature : 360 degree revolving type with single position locking & Chrome base fixed with 5 nos. Nylon castors . 6. Netted Chair Backrest Moulds shall provide adequate back support, and makes the long hours of seating comfortable.

Executive chair big back 1) SEAT/BACK ASSEMBLY: The seat is made up of insert moulded Polyurethane Foam upholstered with foam laminated mesh fabric or net fabric only. The insert moulded foam is assembled over a load bearing plastic seat cover. The back is made up of two piece injection moulded frame. The inner frame is upholstered with mesh/net fabric and mounted on the main assembly. The back has adjustable lumbar support for achieving comfortable seating posture. Average size. (+5cm) Sub Assembly Seat size = 52.5 cm Width, 51 cm Depth. Sub Assembly Back size= 48.5 cm Max Width, 62 cm Ht. Effective Back Height from Seat = 57 cm 2) POLYURETHANE FOAM: The polyurethane foam for seat is moulded with density = minimum 50 ±4 kg/m3 and Hardness = 34 ± 4. 3) ARMRESTS (ADJUSTABLE): The armrest top is injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest. The armrest height is adjustable up to 4-5cm in 3 steps & width adjustable. Arm Top Out to Out Dim = 62 to 65 cm, Arm Top Centre to Centre Dim = 53 to 56 cm. 4) FRONT PIVOT SYNCHRO MECHANISM: The mechanism is designed with the following features: - 360 degrees revolving type - Single point control - Front pivot for tilt 5 with feet resting on ground ensuring more comfort - Tilt tension adjustment – 3 position locking with anti-shock feature 5) CONNECTING SPINE BRACKET: spine bracket is made of Aluminium die cast piece connecting back with mechanism. 6) PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment of 8.5(+2) cm. PEDESTAL ASSEMBLY: Pedestal is made of Die cast Aluminium fitted with 5 nos. twin wheel castors castor wheel dia. 6.0 + 1cm). The pedestal is 65 + 2cm. Pitch centre diameter. (71.0 cm with castors) + 3cm. 7) TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Nylon.

I.V. Stand: Overall approx. size: height – 1360-2440 mm (with telescopic adjustable height) Ht adjustable with top knob (not side knob). Main Frame: Strong & Sturdy five legged neatly made base mounted on five 50 mm diameter swivelling ball castors of good quality. S.S. double hocked I.V. rod & S.S. tube spring loaded. All the Stainless Steel should be 304 grades/ 16 gauge.

Examination Stool Examination stool with ply on top having teak edge banding. Height of the top should be 19''. 16 guage 1''x1'' pipe should be used. All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge and approval of sample of engineer-in-charge.

Big Table Supplying and fixing standard Cabin table i. MAIN TABLE SIZE - 1800MM W x 900MM D X 750MM H, ii. The worktop Will be in single piece made up of prelaminated MDF board. iii. The worktop shall be made of 25mm thick prelaminated MDF board with 2 mm thick hot melt PVC edge banding iv. The top is resting on the vertical strips of MDF board of size 750W x 75H. v. The second table top shall be made up of 25mm thk prelaminated MDF board provided with size 500W x 900D. vi. The modesty of the table is also made up of 18 mm thk. prelaminated MDF board which is attached with the horizontal panels created under second top under main table top. There shall be an standard space for visitor chair in front of modesty panel. vii. The side panels are also made up of 18mm thick prelaminated MDF board with 2 mm thick hot melt PVC edge banding. viii. 3 drawer pedestal shall be provided Size : 450mmW x 450mmD x 685mmH. Top drawer should have a stationary tray made of 18mm thick Pre-laminated MDF board having three drawer configuration, two for personal and one for lateral files. All drawers to be lockable with single key system.

Luggage Trolley Luggage trolley to carry out medical equipments. All as per engineer in charge and sample would be approved.

Office Chair SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumbar support for extra comfort. Mid back Chair BACK SIZE 48.0cm. (W) x 47.0cm. (H) SEAT SIZE: 45.0cm. (W) x 48.0cm. (D) POLYURETHANE FOAM: The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore ‘A’ Hardness and reinforced with M.S. insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.5cm thick. HR steel. TUBULAR FRAME: The tubular frame is cantilever type & made of Dia. 2.54cm (1”) x 14 BG M.S. E.R.W. tube and black powder coated. Should be bifma certified and ISO 14001:2015, 45001:2018 should also be provided.

Office Table 1. Table Top should be made of 25mm THK. ISI Marked Pre Laminated MDF Board IS-14587-1998. with upto date amendment with overall size 1200x600x750mm. 2. Teak wood half round 25mm wide Edge Leaping should be provided with proper edge banding machine 3. Frame Structure :- ERW Square pipe 32 x 32 x 1.25 mm in size1100(L) x 500(W) x 725(H) mm. 4. Drawer & Cupboard:- CR sheet 0.80mm thick Confirming to IS-513 Size = 500(D) x 350(W) x 450mm(H). 5. Drawer Size :- 450(L) x 100mm(D) Minimum. 6. Foot Rest :-ERW square pipe 32 x 32 x 1.25mm in full length. 7. P.U/Rubber Shoes :- P.U / Rubber shoe`s are to be used compulsorily in legs. All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge and approval of sample of engineer-in-charge.

Almirah Providing and Placing in position Storage Unit for Classroom of overall size 910mm(W) x500mm(D) x 1950mm(H) including levellers. The storage unit shall be divided into 2 parts of 500mm(W) each by a vertical partition of 1980mm(H). The storage units shall be stacked widthwise to form a row of storage having a common side panel. The construction of the storage units shall be aesthetically appealing and knock down or welded. Legs shall be fitted in the floor units with screw type leveller and material shall be from combination of CRCA sheet of 0.7mm & 0.8mm thick. The storage units shall be provided with height wise adjustable 4 shelves mounting, each shelf shall have a load capacity of 40 kg Uniforming Distributed Load. The storage will have steel 2 Nos Hinged Door with self closing hinges and individual lock for each door. Each door shall be provided with a handle Ergonomically designed with Aesthetically appealing made from Metal. The complete floor units shall be provided with 3 way locking and Finished with Epoxy Powder coated to the thickness of 60 microns(+/-10). All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge and approval of sample of engineer-in-charge. ISO 14001:2015, 45001:2018 should also be provided.

Computer Chair Providing, supplying and placing of Revolving Computer Chair. The seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The Seat is provided with a pre-moulded inserts at the bottom for fixing Mechnism and Armrests. The back foam is designed with contoured lumbar support for extra comfort. BACK) SIZE: 40.0cm. (W) X 47.0cm. (H) SEAT SIZE: 45.0cm. (W) X 42.0cm. (D). The HR Polyurethane foam is moulded with density=45+/-2 kg/m cube and hardness load 16+/-2 kgf as per IS:7888 for 25% compression. The one piece armrests are injection moulded from black nylon. The armrests are fitted to the seat with armrest connecting brackets made of 0.5cm. thk. HR steel. The permanent contact mechanism is designed with 360° revolving type. 14° maximum back-tilt only.Upright position locking. Tilt tension adjustment. The pneumatic height adjustment has an adjustment stroke of 11.0 cm.The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal is injection moulded in black 30% glassfilled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 62.0cm. pitch-center dia. (72.0 cm with castors).The twin wheel castors are injection moulded in Black Nylon. All the above items should be as per photo, sketch , specifications & direction of engineer-in-charge.

Notice Board Pin up Notice board having size 1200mmx600mm made of softboard core and covered with velvet cloth surface. Colour as per buyer's choice/ engineer in charge.

Shoe Rack Shoe Rack (Small Size) with 03 shelves made of steel.

Computer Table Length: 1200 mm Width 600 mm Height 750 mm Material Of Top Pre-laminated Board with melamine finish Thickness Of Top 18 mm Number Of Legs: NA Material Of Frame 50 mm x 50 mm Board closed loop leg within metal beam below and extended modesty panel in front. Material Of Drawer: 18 mm thick Pre-laminated Board with melamine finish Number Of Drawers 3 Nos. (2 drawers And 1 filing Drawer) Locking With drawers- Yes Provided All Exposed Sides Are Edge Banded With PVC Tape Of Thickness 1.5 To 2.0 Mm- YES Colour Of Laminate: AS USER REQUIRMENT. All the above items should be as as per photo, sketch and specifications as per the direction of engineer-in-charge and approval of sample of engineer-in-charge.