Rajasthan State Road Development And Construction Corporation Limited Tender

2 x 1.5 sq.mm

3 x 2.5 sq.mm

Supply, Drawing and Testing of 4 pair,23AWG Solid Bare Copper wire insulated with PVC, UTP (UnshieldedTwistedPair), Category 6, ClassE, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568,The copper conductors should be balanced twisted in pairs, seperated by across-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100Mtrs channel requirements & transmission frequencies upto 250Mhz. inexisting MS/ PVCConduits/ casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per preapproved by Engineer incharge. For additional technical parameters of products/work,refer Annexure"A" attached with this BSR .

Supply, Installation, & Testing of Indoor duplex Singlemode patch cord (9/125 µm made of glass fiber optic with LSZH jacket, Multimode G652.D Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20 as per latest ammendments of TIA/EIA 569B.3, as per requirements complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Cat 6, UTP (Un-sheilded Twisted Pair) Patch Cord

0.50 Mtr

Supply,DrawingandTesting,ofstrandedSinglemode(9/125μm)glassopticfibercable,asperlatestammendmentsofTIA/EIA568/ISO/IEC11801:2011/IEC60794-1-2,constructionofLSZHoutersheathcable,cableshouldbeusedforLANandWANbackbones,.WithitsLSZHsheathingthesecablesshouldbeidealforindoor/outdoorinstallationsinexistingMS/PVC/HDPEConduits/slottedchannelswithferrulingatbothendsforidentificationcompleteinallrespect.AllasperpreapprovedbyEngineerincharge.Foradditionaltechnicalparametersofproducts/work , refer Annexure "A" attached with this BSR .

6 fiber

Supply, Installation, & Testing of 19" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, Singlemode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable duplex adapters for ST/E-2000/SC/LC/MTRJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirment complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR.

12 Ports

24 Ports

Supply,Installation,OTDRTesting&FusionSplicingofFiberSinglemodePigtail(9/125μm)madeofglassfiberoptic,shouldbefittedatoneendwithanyonetypeofsingleST/E-2000/SC/LC/MT-RJ/PCtypeconnectorinacc.withIEC61754-20,asperlatestammendmentsofTIA/EIA569StandardSpecificationasperrequirmentscompleteinallrespect.AllasperpreapprovedbyEngineerincharge.Foradditionaltechnicalparametersofproducts/work,referAnnexure"A"attachedwith this BSR .

Supply,Installation,&TestingofIndoorduplexSinglemodepatchcord(9/125μmmadeofglassfiberopticwithLSZHjacket,MultimodeG652.DMountedonbothsideswithST/E-2000/SC/LC/MT-RJ/PCtypeDuplexconnectorsinacc.withIEC61754-20asperlatestammendmentsofTIA/EIA569B.3,asperrequirementscompleteinallrespect.AllasperpreapprovedbyEngineerincharge.Foradditionaltechnicalparametersofproducts/work,referAnnexure"A"attachedwith this BSR .

Single Mode Patch Cord 3 Mtr.

Supply and Installation of unsheilded/ sheilded Information outlets made of high impact plastic body with ABS, FR Grade with provision for protection against dust in jack/ FP, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact punch termination on reliable copper tin plated Insulation displacement contact, It complied with ANSI/TIA/EIA 568 standard. In existing modular/MS Boxes along with necessory connections as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR.

Cat 6, Un-sheilded Information Outlet

Supply, Installation, Testing and Comissioning of Rack mounted 19" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels (without I.O.) with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel, . There should be a provision for each port/jack on the panel and reusable removable on field from the panel complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supply, Installation, & Testing of Indoor duplex Singlemode patch cord (9/125 µm made of glass fiber optic with LSZH jacket, Multimode G652.D Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20 as per latest ammendments of TIA/EIA 569B.3, as per requirements complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Single Mode Patch Cord 1 Mtr.

Supply , Installation, Testing and Comissioning of Managed Layer-2 Intelligent Giga Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports and with min 4 SFP Giga Ports (provision for Fiber Giga connectivity) with provision of minimum Stacking of Switches with related LAN Base Software including making connections etc as required complete in all respect complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supply , Installation, Testing and Comissioning of Hot pluggable Small Form Factor Pluggable (SFP Module), 1000BASE-LX, 1G Fiber Channel, LC Type Duplex Connector, 1310 nm laser transmitter, Should support distance upto 10 km on 9/125 um of data rate upto 1.25 Gb/s on bi-directional data links. Should also support industrial temperature, should have metal enclosure for lower EMI. The transceiver should be ROHS Compliant. (For Each SM Fiber) complete in all respect. Switch & SFP module should be of the same make. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR

Supply, installation, testing and comissioning of interconnecting copper refrigerant piping of DHE Grade C12200- ASTM B68, B75, chemical composition of copper %- 99.0 Min and Phosphorus %- 0.015 to 0.040 . For Annealed copper tube :- Tensile strength = 210 Mpa wih elongation % = 40 Min . Ink Mark Brand Printing on Hard Tubes should be present. duly insulated with tubular elastomeric nitrile rubber FM/UL approved with high water vapor diffusion resistance and low thermal conductivity should be certified 'Class O' in Fire Propagation as per BS 476 Part 6 including chase cutting andfilling with mortar, Slotted channel supports mounted on 10 mm threaded rod at suitable spacing the exposed piping shall be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

9.5 mm O.D., wall thinkness ≥ 1.2mm (insulation – 13 mm thick)

6.4 mm O.D., wall thinkness ≥ 1.2mm (insulation – 13 mm thick)

28.6 mm O.D., wall thinkness ≥ 1.2mm (insulation – 19 mm thick)

15.9 mm O.D., wall thinkness ≥ 1.2mm (insulation – 13 mm thick)

Add Extra for Workstation latest Intel® i5 processor, Intel Chipset motherboard, 08 GB RAM, 1 TB SATA HDD at 7200 rpm, with 2 x 4GB GPU type higher end Graphic card for H.265 compression technique with dua display ports/DVI/ HDMI port, Giga LAN Card, wireless Keyboard, wireless optical Mouse. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

SITC of Round Flow type Cassette indoor units comprising with per-filter,drain pump, fan section with low noise fan multi speed motor, coil section with DX coil, outer cabinet, insulation, pipe connections with human occupancy sensor and Variable Refrigerant Temprature Smart technology and following capacities, the cassettes units shall have dual sensor which detect the presence of people and floor temperature to provide comfortable air – conditioning and energy saving. The sensor should detects human presence and adjust the air flow direction automatically to prevent drafts. Room temp should be increase up to 4 Deg C or the indoor unit to be switched off when people are not detected. The sensor should detect the floor temperature and automatically adjusts the operation of the indoor units to reduce the temperature difference between the ceiling and the floor including Lifting, shifting, positioning, installation and testing of following Outdoor / Indoor units, outdoor units,as per specification and drawings. Make: Daikin, Mitsubishi Electric,O General

Round Flow Cassette Type - 2.0 TR + Cordless Remote + Joint

SITC of 55" LED Monitor,17,55" Diagonal Full HD (1920 x 1080) LED Display,1 x HDMI Port,1 x VGA Port,1 x USB Port,Inbuilt media player-should be as per OEM for web browser & file sharing compatibility through IP,External Control-RS232C(in/out) thru stereo jack, RJ45,Contrast Ratio - 4000;1,Response time- 8 ms,Brightness 350 cd/m2 20 Watt Built in speaker,Viewing angle 178° x 178°,Wall mount for Display:,Movable arm Wall mount with 45° Left / Right movement,External media player compatible for above if required Safety & EMC Certifications- CE,FCC,UL,BIS MAKE:Samsung,LG,Panasonic or Make approved by Client department,compitant authority or site Engineer

Supply, Installation, Testing & Commissioning of IP Phones along with Dual switched auto-sensing 10/100/1000 Mbps Ethernet ports with integrated BUILT-IN PoE+ to power the device and give it a network connection, 2 line keys with dual colour LED and 2 SIP accounts, LCD graphical display, 3 XML programmable context-sensitive soft keys, 13 dedicated function keys for: MUTE, CONFERENCE, PHONEBOOK, MESSAGE, RECORD, HOME, TRANSFER, HOLD, HEADSET, MUTE, SEND/REDIAL, SPEAKERPHONE, VOL+, VOL; . Supports HD audio both on handset and full-duplex handsfree speakerphone and 3-way conference. UL & FCC/CE compliance of Approved Makes: Cisco, Alcatel, Grandstream

Supply, Installation, Testing & Commissioning of IP PBXs appliance BOX with 500 Users Call Capacity along with 80 concurrent calls, upto 75 parties voice conference, inbuit 32GB Storage (for call recording), Network Interfaces : Three self-adaptive Gigabit ports (switched, routed or dual card mode) with PoE+, supports router mode and switch mode, Up to 5 layers of IVR (Interactive Voice Response). Call Features: Call park, call forward, call transfer, call waiting, caller ID, call record, call history, ringtone, IVR, music on hold, call routes, DID, DOD, DND, DISA, ring group, ring simultaneously, time schedule, PIN groups, call queue, pickup group, paging/intercom, voicemail, call wakeup, SCA, BLF, voicemail to email, fax to email, speed dial, call back, dial by name, emergency call, call follow me, blacklist/whitelist, voice conference, video conference, eventlist, feature codes, busy camp-on/ call completion, voice control. UL & FCC/CE compliance of Approved Makes: Cisco, Alcatel, Grandstream

Supply, Installation, Testing & Commissioning of E1/T1 Digital VOIP Gateway BOX for digital PSTN & ISDN trunks to be integrated with IP PBXs with VoIP network with 30 concurrent calls with Dual Gigabit autosensing RJ45 network ports, TLs and SRTP security encrption technology to protect calls and accounts, supports a wide range of voice codecs including G.722, G.729 iLBC, USB and SD card interface peripheral ports. UL & FCC/CE compliance of Approved Makes: Cisco, Alcatel, Grandstream

Supply Installation Testing & Commissioning of Managed Layer-3 Intelligent Ethernet Enterprise Catalyst Series Central Switch providing 24 unpopulated 1000BASE SFP with option for min 2 unpopulated SFP upgradable to 40Gbp SFP, with option for min 8 unpopulated SFP upgradable to 10Gbp SFP, 1 x Fixed AC power supply and option for RPS with following specifications: Minimum of 24 ports unpopulated SFP Supporting 1000SX, 1000 LX, 1000BX, 10G SR/LR, and 100 FX interfaces, Switch should support 8 x 10Gbps SFP+ fully activated ports additional and exclusive to above required ports; SFP+ Ports shall be enabled for 10G operation, Should have USB port for Image backup and storage, should have dedicated and Exclusive stacking ports with stack bandwidth of 40 GBPS, have Redundant Power Supply support and variable speed fan to adjust to varying weather conditions in campus, Design & Performance: Each switch should have 208 Gbps or more with non blocking architecture and Forwarding rate of 154 Mpps, Switch Should be equipped wit minimum 8Gb DRAM and 16 Gb flash, Should have LED indicator for per port status , FAN, PSU and Management Status, Hardware and software configuration have for IPv6 from day one, Switching: Should have 32000 MAC Address, 4094 active Vlans, Should have Port based VLAN, MAC based VLAN, private vlan and MVR,Should have Should have 8 Hardware QOS Queues per port ,Should have MAC address tracking and notification for mac address addition , delete or movement in the Network,Should have minimum 8000 Multicast routing scale, Should support L3 routing protocols like OSPF, RIP,Switch should be upgradeable to support, with provision of retundent power supply with related IP Base Software, Switch Should be UL, EN, IEC, AS, IEEE 802.3 Certifications. All switches & related Fiber modules should be of same make & category for seamless integration with each other. All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with PWD Electrical BSR 2022.

SITC of VRV/VRF outdoor units with multiple compressors complete with full inverter type scroll compressors, including topping R410A gas per site requirements, lifting, shifting, positioning, Cooling Only mode option,G type heat exchanger condenser, low noise direct driven propeller condenser fans in each module with top discharge, outdoor unit more than 14 HP should have minimum 2 nos. condenser fans, Each outdoor unit should have full DC Inverter Scroll compressors & Should have single inverter scroll compressor till 14HP. 16HP and above single outdoor unit shall have 2 Compressors. Each system shall have Single/multiple Outdoor unit modules & each module shall have single/multiple Inverter based scroll compressors as per below mentioned capacities. In case of any outdoor unit failure, the rest of system should be capable of operation, Automatic Sequencing operation, Automatic Refrigerant Charge function, smart function with variable evaporating refrigerant temp, Microprocessor panel with sequential starting of condensing unit, coils, expansion valves, filters in refrigerant circuits, phase reversal preventer, all vibration isolators, safeties, Operating range of dry bulb temperature 10 to 49 Degree C (i.e in cooling mode Make must be compatible with the existing VRV System

20HP

SITC of IGBT based ,ISO 9001, ISO 45001 and ISO 14001 Certificate , 20KVA Online UPS , 3 Phase input and 3 phase 415 V output UPS system with isolation transformer , suitable for operating in parallel and each comprising as per technical specification complete as required. VRLA sealed maintenance free batteries for 20 KVA UPS system, for providing 30 minutes back up .Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required.(cost Included in above) Matching cabinet to house SMF batteries for 20 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.(Cost Included in above) Make:- Numeric /APC / GE

SITC of drain pump for hi-wall machine of HVAC system having features Max. flow 12L/h @ 0 head, Max. rec. head 10m, Max. suction lift 2m, Sound level@1m 21dB(A), Power supply 230V AC 50-60Hz 0.1A, Max. unit output 16kW / 54,000Btu/h, Max. water temp 40oC / 104oF, Discharge tube 6mm ID, IPX4, Safety switch 3.0A Normally closed, Thermal protection, Fully potted, Self priming Make: Aspen/BlueStar/Voltas

SITC of PTZ Camera VC having 70° FOV; Controll settings of pan, tilt & zoom 10x optical & digital; full HD (1920 x 1080) progressive signal; auto focus; Support H.264; Support compression format H.264 with 60fps compression with USB connectivity; Floor/Ceiling Mount Stand; Operating huminity 85%;

SITC of Conference wired/bluetooth table top microphone having coverage 8 meters, 360 degree range Bi-directional noise compression