Rajasthan State Mines And Minerals Limited Tender

P & F 1st quality Vitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete. size 600 mm X 600 mm 7.19.2

Providing and fixing 1st quality MAT & GLOSSY finished ceramic tile confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). Size 300mm x 600mm 7.22.3

Providing & Fixing premium qulaity WVC Wash basin with C.I. brackets duly painted & 32 mm C.P. brass waste coupling of approved make with PVC waste pipe complete:-Size 550 mm x 400 mm 1.71.1

P & F 1st quality WVC pedestal for wash basin. 1.40

P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. - Flat Back (large) or half stall size 610x400x80mm. 1.14.2

P & F C.P. brass Urinal Spreader for stall urinal of approved make. 1.29.1

P & F W.V.C. Urinal Partition Plate of approved standard make of size 630x315mm including making good the wall. 1.15

P & F C.P. brass Doom Waste Coupling 32 mm dia. 1.30.1

P & F 15 mm. Dia Connection Pipe of approved quality/make : PVC pipe with C.P. Brass nuts upto length, 300mm 2.13.1

C.P. Pillar cock, 15 mm dia nominal bore 2.6.1

Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge19-08-2021:- Angular stop cock with long thread 15 mm nominal size 2.33.6

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal bore. 2.7.3

P & F Stop Cock (IS :8931 Mark), superior quality & of approved make:Brass : 1350gm. 25 mm nominal bore. 2.8.3

Providing and fixing Polyethylene - Aluminium -Polyethylene (PE-AL-PE) Composite Pressure Pipes as per 15450 : 2004 U.V. stablised with carbon black having thermal stabillity for hot and cold water supply, capable to withstand temperature upto 80 oC including all special f withittings of composite material (engineering plastic blend and brass inserts whwnever required) e.g. elbows, tees, reducers, couplers connectors etc.with clamps at 1.00 metre spacing.This include the cost of cutting chases and including testing of joints complete as per direction of Engineer In charge . --Concealed installation including cutting chases and making good the walls etc. complete. 1620 (20mm OD) pipe 2.30.2

do- 3240 (40mm OD) pipe 2.30.5

Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make19-08-2021:- 110 mm dia 3.44.2

Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc. :-PVC pipe 110 mm dia 3.16.5.1

PVC pipe 160 mm dia 3.16.5.2

Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make :- Nahni Trap with Jali 4” :- 110mm dia 3.45.25

P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant::- Plain Tee- (ii ) 110mm dia 3.17.3 (ii)

Door Tee : 110mm dia 3.17.4 (ii)

160 mm dia (iii)

Bend 45: (ii) 110mm dia 3.17.8

Door 'Y':- (ii) 110mm dia 3.17.5

Construction of Cement Concrete Chamber 125mm dia on depressed floor upto 45cm height from floor with :Stainless Steel Sheet Grating 3.39.4

P & F Looking Mirrors with P.V.C. frame of approved make as per direction of Engineer-in-charge:- Size 500x400mm 1.45.1

P & F Soap Dish or Tray of approved quality/make:- C.P. brass 1.52.1

P & F Liquid Soap Container with brackets complete of approved make:19-08-202: -C.P. brass 1.49.1

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge. 16.19

Providing and fixing to existing door frames 30mm thick factory made polyvinyl chloride (PVC) door shutter made of stiles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2mm +/- 0.2mm with inbuilt decorative moulding edging on one side. The stiles and rails mitred and joined and the corners by means of M.S.galvanized/plastic brackets of size 75x220 mm having wall thickness 1.0mmand stainless steel screws. The stiles of the shutter reinforced by inserting galvanized M.S.tube of size 25x20 mm and 1mm +/- 0.1mm wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2mm +/- 0.2mm wall thickness fixed to the shutter stiles by means of plastic/galvanized M.S.tube ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 610mm,having overall thickness of 20mm and 1mm+/- 0.1mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6mm galvanized M.S.rod and fastened with nuts and washers.complete as per manufacturer’s specification and direction of Engineer-in-charge.(For W.C.and bathroom door shutter) 16.18

Providing and fixing aluminum work for doors , windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). :- Polyester Powder coating aluminum ( minimum thickness of powder coating 50 micron) 16.1.1.3

For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately).:- Powder coating aluminum ( minimum thickness of powder coating 50 micron) 16.1.2.2

Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.):- With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) 16.5.2

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. :- With stainless steel cover plate 16.6.1

Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. 16.7

Providing and fixing aluminium U shape handle of size 100mm with SS screws etc. Complete as per direction of Engineer-in-charge :- Polyester powder coated minimum thickness 50 micron aluminium . 16.9.3

Dismantling & Disposal of demolition waste -Male Toilet/Floor NON BSR ( on each floor ground , first, second and third floor total 4 number of toilet/floor)

Dismantling & Disposal of demolition waste -Female Toilet/ Floor NON BSR( on each floor ground , first, second and third floor total 4 number of toilet/floor)

Civil repair & painting including all material-male toilet / Floor NON BSR ( on each floor ground , first, second and third floor total 4 number of toilet/floor)

Civil repair & painting including all material-female toilet / Floor NON BSR ( on each floor ground , first, second and third floor total 4 number of toilet/floor)

Miscellaneous Items as per BSR @ 4.5% of above