Rajasthan Rajya Vidyut Prasaran Nigam Limited Tender

Supply of Executive Table size 1500 Wx 750 Dx 725 H (Approx); Top: 18mm made of Thick Pre-Laminated board with 2mm thick PVC edge banding on outer edges; Under Structure; (a) Modesty Panel: 18 mm thick pre laminated particle board; (b) MoEpoxy Polyster coating finished recatngular frame fabricated in 1.2 mm thick CRCA; (c) Epoxy Polyster Powder coated Fabricated Legs;38mmx25mm 1.2mm thick MS ERW ATube; (d) Injection moulded Propylene Cable travel cap and nylon 6 leveler glide with MS Bolts (e) Shell storage with drawer tray 0.6 mm thick & front 0.8mm thick CRCA epoxy polyster powder coat with 10 lever lock, handle and leveller; (f) 0.7mm thick horizontal wire carrier & 0.8 mm thick vertical wire carrier system CRCA epoxy polyster finish powder coat of standard make. as approved by engineer incharge

Supply of Executive High Back Revolving Chair - The seat and back shall be made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and shall be upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of the back shall be 49.0 cm. (W) x 71.0 cm and of seat shall be 49.0 cm. (W) x 44.0 cm. (D). The HR Polyurethane foam shall be moulded with density= 45 ±2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest tops shall be injection moulded from black Polypropylene. They shall be fitted to tubular armrest supports made of dia 2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). The tubular armrest supports should hold together the seat and back. The mechanism shall be designed with 360° revolving type, 1r ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment shall have an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal shall be fabricated from 0.2 ± 0.02 cm thick HRsheet (IS :DD 1079/ HR ), powder coated .(DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal shall be 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors).The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 42.4 to max 53.4cm, Height - min102.4 to max 113.4cm, Width & Depth of Chair as measured from pedestal - Width-70.0 cm and Depth-70.0 cm.

Supply of Executive medium back chair with seat/back made of dimensions 50.0 cm (W) x 45.0 cm (H) (approx.) and overall height of Chair 90.0 cm (approx.) with a seat height of 55.0 cm (approx.) ; Overall width & depth of chair from pedestal 70.0 cm (W) x 70.0 cm (D) (approx.) ; Upholstered with fabric, High resilience polyurethane foam armrests and tubular frame; Center tilt mechanism, 360 degree revolving mechanism, 17 + /- 2 deg tilt on pivot at center, Upright position locking. Tilt tension adjustment Pneumatic height adjustment, Telescopic bellow assemble, Pedestal assembly with twin wheel castors of standard make.1079/ HR ), powder coated .(DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal shall be 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors).The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 42.4 to max 53.4cm, Height - min102.4 to max 113.4cm, Width & Depth of Chair as measured from pedestal - Width-70.0 cm and Depth-70.0 cm.