Rajasthan Rajya Vidyut Prasaran Nigam Limited Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 4,94,500Document Cost
₹ 5,900Tender Fee
₹ 2,360
Summary
Construction Of Control Room With Development Work, Parking, Store Shed, Guard Hut, Boundary Wall, Fencing Work, Water Supply System And Water Harvesting System At 132 Kv Gss, Daizer, Distt. Jodhpur
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_RRVPN_430279_2Tender No
NIT No. 11 (2024-25) SE (Civil) JodhpurTender Authority
Rajasthan Rajya Vidyut Prasaran Nigam Limited ViewPurchaser Address
-Website
http://http://energy.rajasthan.gov.in/content/raj/energy-department/rajasthan-rajya-vidyut-prasaran-limited/en/home.html
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering All up to plinth level IS 456-2000: 1:4:8 (1Cement :4 Course Sand :8 Graded stone aggregate 40 mm nominal size. .( B-3.1.6)
339
3302
1119378
(B)M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size). (B/3.1.3) @ 4544.00/-
8
4544
36352
Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: : Cement Sand Mortar 1:6 (1-Cement:6-Sand).(B -6.1.6)
1154
2838
3275052
Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricks Cement mortar 1 : 6 (1 cement : 6 coarse sand) (B/5.1.2)
120
4263
511560
Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: : Cement Sand Mortar 1:4 (1-Cement:6-Sand).(B -6.1.4)
55
3182
175010
Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in :Cement Mortar 1:6 ( 1-Cement : 6-Sand) Cement Mortar 1:6 ( 1-Cement : 6-Sand). (B/6.2.6) + Add for wall upto 30 cm thickness (B/6.3.4)
422
3665
1546630
Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in :Cement Mortar 1:6 ( 1-Cement : 6-Sand).Square or Rectangular pillars (b/6.2.6+6.3.1) @ Rs 3479+173=3652
54
3652
197208
Half brick masonry in foundation & plinth using bricks of designation 75 - Cement Sand mortar 1:6 (1-Cement:6-coarse sand). (B/5.7.3)
77
470
36190
Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) (B/5.2.2)
5
4990
24950
Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 - Cement Sand mortar 1:6 (1-Cement:6-coarse sand). (B-5.8.3)
265
526
139390
Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-incharge : Profile E (B/9.6.3)
25
506
12650
Profile B: (B/9.6.1)
85
429
36465
Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formaldehye resin, in glue both sides with approved steel fittings complete as per Annexure ‘A’. 30mm thick shutter - Commercial Veneer both side:. Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13. ( B-8.13.2.1+8.14)
34
1982
67388
Providing and fixing fully panelled /partly panelled double leaf shutters frame for windows and ventilators as per approved design and drawings with approved steel fittings as per Annexure „A‟ and width of styles, bottom and top rails 75mm including intermediate rails 50mm wide, beading of
25mm x 15mm size on both faces : 30 mm thick Shesham wood grade - I (B-8.5.2.3) ; Wire gauge 24 gauge 14 mesh of IS 1568-1970 marked 85 gauge wires of dia 0.56 mm (8.6.8)
12
2740
32880
Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement M20 grade Nominal Mix / Design Mix (B/4.1)
150
4934
740100
Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. M20 grade Nominal Mix / Design Mix (B/4.2)
33
5609
185097
Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix (B/4.3)
139
5185
720715
Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls (any thickness) including attached pilasters, coloumns, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, plain window sills, fillets etc up to floor three level excluding the const centering and shuttering.1:2:4 (1-Cement:2-coarse sand:4-graded stone aggregate 20 mm nominal size).(B-3.2.2)
18
5112
92016
Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Thermo-mechanically Treated bars (Conforming of relevent IS code) (B/4.13.3)
33641
77
2590357
Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. (B/4.9)
342
157
53694
Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam, plinth beam etc. (B/4.10.2)
1160
340
394400
Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Columns, pillars, posts and struts etc. (B/4.10.3)
566
375
212250
Supplying and fixing machine cut and polished stone shelves, tands and sills in CM 1:3 with machine cut edges: Kota stone minimum 30 mm thick. (B/6.17.3)
85
609
51765
Providing and fixing Marble stone flooring table rubbed, 15-18 mm thick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Kesriaji / Abu Ambaji (Green Marble). Size upto 1500 Cm2 (B/7.3.1)
60
1084
65040
(B) Providing and fixing 50mm thick cement concrete flooring with Metallic concrete hardener topping, under layer of 38mm thick cement concrete 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm thick nominal size) and top layer of 12mm thick metallic concrete hardener consisting of mix 1:2 (1 cement : 2 stone aggregate, 6mm nominal size) by volume & mixed with metallic hardening compound of approved quality @ 2Kg./Sqm including cement slurry, rounding off edges etc. but excluding the cost of nosing of step etc. complete. (B/11.4)
137
453
62061
Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. For area of each slab from 2001 to 5000 Sqcm. (B/11.19.2)
6
1002
6012
Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)For area of each slab up to 901 to 2000 Sq. Cm ( B -/11.18.1)
100
950
95000
P & F 1st quality Heavy Duty Vitrified Double Charged tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete. Size 600mm X 600mm (B/7.25.1)
360
1041
374760
Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed) (B/7.13)
50
748
37400
Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). (B/7.12)
140
674
94360
Providing and fixing aluminum work for doors windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For fixed Portion Anodised aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer) (B/16.1.1.1)
400
326
130400
Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately).For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately).Anodised aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer) (B/16.1.2.1) @ Rs 355.00 P Kg
620
355
220100
Providing and Fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II confirming to IS 12823 bonded formaldehyde synthetic resin of approved brand and manufacture in paneling fixed in aluminium doors, windows/ stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. (B/16.4.1)
9
1030
9270
Providing and fixing 10mm brass lock (best make of approved quality) for aluminium door including necessary cutting and making good etc. complete. (B/16.8)
7
328
2296
P&F double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked for doors including costof cutting floors as reqd. embedding in floor and cover plate with brass pivot and single piece MS with stainless steel cover plate. (B/16.6.1)
14
1426
19964
Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm. (B/8.25.2)
40
266
10640
Providing & laying broken glazed titles on roof ( broken glazed tiles not less than 9 Kg/Sqm) on top of hot bitumen @ 1.7 Kg/Sqm. (1.40 Kg of VG-40 (30/40 )grade and 0.30 Kg/Sqm. Of VG-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of Engineerin-charge. (B/10.24)
717
317
227289
Grading roof for water proofing treatment with water proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) (B/10.17.1)
68
4483
304844
Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20 mm thick (B/12.3.2)
1650
190
313500
Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 12 mm thick (B/12.3.3)
800
160
128000
Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish : 12 mm thick (B/12.2.3)
235
163
38305
6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3- fine sand) (B/12.5)
425
139
59075
Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 25 mm thick (B/12.3.1)
1475
211
311225
Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish : 25 mm thick (B/12.2.1)
2450
227
556150
Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish : 20 mm thick (B/12.2.2)
370
202
74740
Pointing on stone masonry in cement sand mortar 1:3 (1 cement : 3 sand) :Flush / Ruled/ Struck or weathered pointing. B-12.31.1 @ 124.00/-P.Sqm
2450
124
303800
Pointing on stone masonry in cement sand mortar 1:3 (1 cement : 3 sand) : Deep groove pointing (B/12.31.3)
370
220
81400
Add extra for facing as per design and detailed specifications including additional cost of stones - Course rubble facing Second Sort.( B/ 6.4.2)
416
491
204256
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) Dark shade using ordinary cement. (B/11.17.3)
190
523
99370
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost. of aluminium snap beading shall be paid in basic item.) : With glass panes of 5.0mm thickness (weight not less than 13.50 Kg/Sqm) (B-200 / 16.5.2)
80
902
72160
P&F expanded grill made of anodised aluminium as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminium window/ vent with reqd. screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. Anodized Aluminium (anodised transparent 81 dyed to required shade according to IS:1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer) (B/16.10.1)
80
1775
142000
Extra for providing edge moulding to 15-18mm thick marble/Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work - Full Edge moulding (B/7.6.1 (i))
250
146
36500
Providing and fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25 mmx 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge (B-9/9.39 )
30
3895
116850
Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Grade 204 (B/16.56 b)
10
432
4320
Providing glass strips in joints of terrazzo/cement concrete floor : 40 mm wide and 4 mm thick. (B/11.9.1)
55
31
1705
Making grooves as per design in plaster 10mm to 20mm wide. (B/12.19)
450
7
3150
Providing gola 75mm x 75mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finished with cement mortar 1:3 as per standard design. (B/10.22 )
300
111
33300
Random rubble dry stone Kharanja under floor. (B/11.26)
70
932
65240
Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods watering, rolling each layer with 1/2 tonne roller, or stone or steel rammers and rolling every 3rd and top- most layer with power roller of minimum 8-10 tonne capacity and dressing up in embankment for roads, flood banks marginal banks and guide banks or filling up ground depressions, lead up to 50 Mtr. and lift up to 1.5 Mtr.:Hard rock(blasting prohibited) useful material 30%.(B-1.2)
670
272
182240
Add. Extra for Lead up to 5 KM for carriage of Earth, Sand, Lime, Morrum manure or sludge (G-4/4.1) @ Rs 125.00 P cum
670
125
83750
Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (IS 1038-1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate
20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws
complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : Windows side hung /Ventilators top or centre hung (openable) (B/9.19.3)
10
3135
31350
Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. (B/9.26)
10
617
6170
White washing with lime to give an even shade including all scaffolding: New work (three or more coats). (B/12.34.1) @ 11/-
380
11
4180
Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint (B/9.17) @ 2869/- Add extra for double leaf shutters. (B/9.17.1) @ 20%
9
3442
30985.2
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: (B/9.2)
5193
81
420633
Supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade No. 2 and M.S. top cover 1.25mm thick for rolling shutters as per design & IS 6248- 1979. (Clear openable area to be measured for payment). (B/9.13) @ 2074/-
7
2074
14518
Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide (B/9.8)
9067
96
870432
Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size. Welded mesh 25 mmx 25 mm x 2.1 mm (B/9.38.3) @ 750/-
138
750
103500
Add or deduct for each wire line over basic item (B-9.33)@ 12.00/- P.MtrExtra for using galvanized barbed wire instead of black barbed wire.(B-9.35)@13.23/- P.Mtr.
6916
13
91498.68
Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. (B/9.5)
100
83
8300
Providing and fixing sun control film, thickness of film 1 Mil Visible Light Transmittance 4-24% & Solar Energy Transmittance 42-51% & Total solar Energy rejection 37-43%of approved colour and shade , complete in all respect , at all level , as directed by engineer- in -charge. (B/16.15)
80
639
51120
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete (B/12.23)
2600
69
179400
Providing and fixing Nigeria / Ghana /Ivory Coast Teak wood grade-I mouldings and beadings in doors and windows size :- 25x12 mm (B/8.23.3)
107
72
7704
Stone slab roofing on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4, with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of Engineer In Charge (B/10.16)
81
1648
133488
Supply of river sand : single size with lead 40 KM (Input material code-304)(G/4.1) (1800+240+20x7)=2180
3
2180
6540
Supply of Stone Aggregate (Single size) : 20 mm nominal size with lead 5 KM (Input material code-295) (G/4.2) Rs 1100.00+125=1225
3
1225
3675
Supply of Stone Aggregate (Single size) : 40 mm nominal size with lead 5 KM (Input material code-293)(G/4.2) Rs 990.00+125=1115.00
3
1115
3345
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work (B/12.46.1)
699
69
48231
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats) over and including scrapping and priming coat with cement primer. (B/12.37.1) @ 75/-
1770
75
132750
Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision New Work (B/12.43.1) @ 123/-
2585
123
317955
Colour washing of all shades to give an even shade including all scaffolding :New work (two or more coats) with a base coat of whiting.(B-12.35.2)@15/-
2901
15
43515
Providing & fixing precast cement concrete coping 1:2:4 mix 50 mm thick complete as per specification : ( B/ 3.8 )
423
367
155241
Finishing with neat cement (Punning).B.12.7
135
36
4860
Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. (B/1.25) @ 64/
3
64
192
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 1.00 mm thick with zinc coating not less than 275 gm/m2 (B/10.1.1) @ 904/-
7
904
6328
Providing and fixing 14 mm thick Acoustical with fine fissured tiles/ Mineral fibre high density tiles with butt edges false ceiling tiles of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge. ( The tiles should of 90 % RH avg. NCR 0.55 light reflectance 80% thermal conductiveity K = 0.052-0.057 w/m K colour white. Fire performance class 0/class I(BS 476) with warranty against sag) (B/10.28) @ 1063/-
280
1063
297640
S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. (B/16.11)
15
925
13875
P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440mm. (B/1.2.2) @ 3080/-
3
3080
9240
P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor (S/1.3) @ 2420/- Each
3
2420
7260
P & F water closet Seat Covers with brass hinges complete : Solid PVC (IS 2548 marked) grade-I White. (S/1.7.2) @ 485/-
3
485
1455
P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. Flat Back (small) size 456x355x265mm. (B/1.14.1) @ 1832/-
5
1832
9160
P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and making good the wall: PVC with PVC bend as per IS : 7231 . (B/1.20.2) @ 1291/-
3
1291
3873
P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 550 mm x 400 mm (S/1.36.3) @ 2598/-
6
2598
15588
P & F Looking Mirrors with P.V.C. frame of approved make as per direction of Engineer-in-charge Size 500x400mm (B/1.45.1) @ 351/-
6
351
2106
P & F Towel Rail or Ring of approved quality/make: C.P. brass Towel Rail elbow type with concealed screws size 450 mm (Heavy duty). (S/1.47.1) @ 468/-
3
468
1404
B) C.P. brass towel ring revolving type (S-11/1.47.8)
5
254
1270
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 15 mm nominal size (B/2.37.1) @ 191/-
75
191
14325
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 25 mm nominal size (B/2.37.3) @ 282/-
43
282
12126
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work). 15 mm nominal size (S/2.39.1) @ 167/-
320
167
53440
25 mm nominal size (S/2.39.3) @ 262/-
190
262
49780
50 mm nominal size (S/2.39.6) @ 757/-
100
757
75700
Making connection of G.I. distribution branch with G.I. main including all fitting.Up to 25 mm dia (S/2.3.1 )
9
265
2385
P & F Bib Cock (IS:8931 Mark) Superior quality of approved make : (a) C.P. Brass bib cock, 15 mm nominal bore. (S/2.7.3)
12
590
7080
(b) -do- Long body, 15 mm nominal bore weight not less than 690 gm. (S/2.7.4)
10
783
7830
C) C.P. Brass Two way Bib Cock 15 mm (S/2.33.5)
5
1174
5870
P & F Stop cock (IS:8931 Mark) superior quality & of approved make : (a) C.P. Brass 15 mm nominal bore. (S/2.8.4)
7
477
3339
(b) -do- Concealed Stop Cock 15 mm. (S/2.8.5)
6
1009
6054
Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B' for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make.110mm dia(S/3.44.2)
150
336
50400
Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B' for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make.110 mm dia.( S/3.45) Bend 87.5 Dg.
19
155
2945
Single Tee with Door
4
242
968
Vent Cowel 100mm
2
59
118
Socket
11
76
836
Bend 87.5 Dg.
15
155
2325
Pipe Clip
39
31
1209
Nahni Trap without Jali 4"
17
152
2584
P&F rigid PVC Pipe (IS:4985 mark) class II(4 Kg. /Cm.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant (A)110mm dia (S/3.16.5.1)
197
282
55554
(B)160 mm dia S/3.16.5.2
135
425
57375
P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: (S/3.17) Bend : 87.5 0
18
161
2898
door Bend : 87.5 0
2
154
308
Bend : 45 0
4
128
512
tee door
2
213
426
Pipe clip
42
36
1512
Coupler
20
108
2160
Providing and fiixng C.P. flange for 15mm dia tap.s (S/1.60)
29
18
522
P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres (S/2.26.3) @ 3920/-
5
3920
19600
P & F Full-way valve(IS:778 Mark) or wheel valve of approved make :( S/2.15.1 , 2.15.3, 2.15.6)(A) Gun-metal 15mm nominal bore
15
227
3405
(B)Gun-metal 25mm nominal bore
10
529
5290
(C)Gun-metal 50mm nominal bore
3
1464
4392
P & F Flush Cock/Flush Valve (IS:9758 Mark) or WC of approved quality make C.P. brass Half-turn exposed 25 mm nominal bore. : .(S/2.14.7)
3
783
2349
P & F 15 mm. Dia Connection pipe of approved quality/make: PVC pipe with C.P. Brass nuts up to length 450 mm. (S/2.13.3)
10
101
1010
P & F Ball Cock (IS:1703 Mark) with Rod & P.V.C. Ball complete : Brass wt.400 gm. 15mm. S/2.11.2
5
372
1860
Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) all around S.W. pipe including 15 Cm. thick bed concrete (Width W= Diameter of pipe in Cm+30 Cm.)( Excluding cost of pipe). 100mm dia S.W. pipe (S/3.2.1)
210
457
95970
Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth up to 0.5 M (B/3.19.1) @ 5489/-
6
5489
32934
Depth upto 0.6 mtr ( Sewar Line + Rain Water) (1+2)
3
5695
17085
Depth upto 0.7 mtr ( Sewar Line + Rain Water) (1+1)
6
5901
35406
Depth upto 0.8 mtr ( Rain Water) (1)
5
6107
30535
Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame. (S/3.21.1) @ 1049/-
6
1049
6294
Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B' for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make. Gully Trap 160mm S/3.45.24
5
685
3425
Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: Size 300 Cm. dia outside & 300 Cm. depth . (S/3.22.1) @ 24135/-
2
24135
48270
Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:- Size 200x100x130 cm.(for 10 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c bothways including shuttering complete in all respect. (S/3.27.1)
2
27322
54644
P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. (S/1.59) @ 381/-
1
381
381
Construction of Cement Concrete Chamber 125mm dia.C.P. Brass doom grating (S/3.38.2) @ 177/-
17
177
3009
P & F Shower arm 15mm dia of approved quality/make. C.P.brass heavy & superior quality 150mm Projection. (S/1.54.1) @ 198/-
3
198
594
P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked) (S/2.12.1) @ 501/-
12
501
6012
P & F C.P. brass Urinal Flush Pipe set complete with flanged brackets of approved make. For 1 Urinal (S/1.28.4) @ 504/-
1
504
504
P & F Soap Dish or Tray of approved quality/make C.P. brass heavy and superior quality. (S/1.52.2) @ 156/-
5
156
780
P & F Bath Shower of approved quality/make. C.P. brass of Heavy & superior quality 150mm. (S/1.55.2) @ 376/-
3
376
1128
Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge Angular stop cock with long thread 15 mm nominal size (S/2.33.6) @ 762/-
5
762
3810
P&F Gun metal non return valve or check valve IS make of approved make superior quality; 50 mm, horizontal (S/ 2.16.6)
1
1416
1416
Development of tube well as per IS specification using suitable compressor to give sand free water for required yield of the gravel packed tube well.(S/4.4)
12
600
7200
S & F tube well cover of tube well cover of M.S. sheet (6mm thick) with nuts and bolts complete for casing size :200 mm dia (S/4.8.4)
1
373
373
S&F MS clamps set of 50x6mm flat from ion with nuts and bolts et c. for holding the riser pipe assembly of submersible pump set. (S-4/ 4.9)
1
266
266
1.0mm thick salem stainless steel AISI -304 kitchen sink of approved make (Nirali, Neel- Kanth, Jaina, Faber, Cryistal) with large waste coupling. Size Size 24x18x8 (S-1/1.38.9.3)
2
5062
10124
Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe: 200 mm Nominal bore. (S/4.2.4) @ 999/-
540
999
539460
Supply of ERW M.S. black casting pipe ISI marked (IS:4270/1992) of grade Fe 410 of following sizes at site of work.200 mm nominal bore (S-4/4.5.4)
255
1728
440640
Supply of strainer pipes made of ERW MS black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS 8110-1985,200 mm nominal bore (S-4/4.6.2)
215
2031
436665
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%