Rajasthan Housing Board Tender

ROWER : Area :- 1.2 x 1 Mtr Safe Area :- 1.5 x 1.5 Mtr Providing and fixing including one year Warranty with free maintenance; Rower made from "B" class G.I. pipe. the main frame is of 80mmx40mm & 40mmx40mm CRC pipe with 2 mm thickness. the handle frame is of Ǿ 32 made from "C" class G.I.pipe. the foundation used for fixing consists of three equal items i.e. Ǿ 40mm made from "C" class G.I.pipe, c channel of 75mmx40mmx5mm & 25mmx25mmx3mm M.S. angle. to join the movement frame to main frame seamless pipe of Ǿ 50mm & 3mm thickness is used. the seats which are fitted on the main frame is made up of high quality FRP material of size 330mmx300mm of thickness 3 mm & M.S.plate of size 250mmx200mmx5mm is used to support it. closing caps are made from top quality FRP material which is of 2 mm thickness. the pins used are made up of Ǿ 17 mm hardened bright bar. the bearings used are of "6203zz" permanent lubricated sealed bearing of reputed make (FAG/SKF) the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the bushes (Stopper) used to avoid the collusion. the serclips used for assembly is of Ǿ 17 mm. the powder coat is done by poly urethane & epoxy powder with 60 to 70 micron thickness.

SURF BOARD : Diamensions :- 910mm (Length) x 860mm (Width) x 1400mm (Heigth) Safe Area :- 1.39 x 1.27 Mtr. Providing and fixing including one year Warranty with free maintenance; Surf board equipment made from "B" class G.I. pipe of different NB. NB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. The center pipe is of 100mm NB made from "B" class G.I. pipe. The sleeve pipe is of 125mm OD seamless pipe with thickness of 5 mm and bolted to main frame with M 10 SS bolts. The bottom support welded of M.S. plate of Ǿ 250mm & 10mm thickness. The handle frame is of 25 NB made from "B" class G.I. pipe. The paddle frame is of 50 NB made from "B" class G.I. pipe is supported with 70x8mm bend M.S. flat and can be replaceable. the foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "B" class welded with M.S. round plate of Ǿ 250 mm & 10 mm thick. main pipe supported with 25 mm x 25 mm M.S. angles of 3 mm thickness and 20mmx40mm CRC square pipes of 3 mm thickness. Bushes are used 70mm outer diameter with 5mm thickness is used. the footrests made from injection moulded plastic LLDPE/HDPE for support to footrest 200mmx250mm with 3 mm thickness M.S. plate used. Closing caps are made up of injection moulded plastic LLDPE/HDPE. The pins used are made up of Ǿ 35 mm SAE 8620 bright material. The bearing used are of "6007zz" permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly is of A 34. The powder coating is done with pure polyester powder of Ackzonoble or berger with 60 to 70 micron thickness.

AIR WALKER : Providing and fixing including one year Warranty with free maintenance; MACHINE PART DESCRIPTION OF THE AIR WALKER (a) Mounting plate (b) Center pillar (c) Trapezium shaped pipe (d) Cap (e) Holding pipe (f) Hinge supporter (g) Obtuse L shaped pipe (h) Rectangular pipe (i) Standing pad (j) Triangular hinge supporter 1 A circular mounting plate of diameter 233mm and thichness 8mm, 4 holes on this plate at 90 degrees of which PC.D. 170mm hole diameter is 20mm. 2 On circular mounting plate a center pillar is welded. Diameter of center pillar is 114mm and height is 233mm. 3 Trapezium shaped pipe is welded to the center pillar from the middle at the base. Trapezium shaped pipe's upper portion is open with two branches. 4 Cap is on the two branches of upper portion/top of the branches are 925mm wide and length of each branch is 885m. At the base of the branches the gap is 925mm with a radius bend 235mm. 5 Open end of Trapezium shaped pipe is welded with a holding pipe. Holding pipe has a straight length of 810mm and a 90 degrees radius on the both sides, then a small straight length of 246mm. throught this small straight length holding pipe is welded to trapezium shaped pipe. Holding pipe is welded at an angle of 40 degrees to the open ends of trapezium shaped pipem height of joint is 1212mm. 6 Hinge support of length 126mm is welded on the branches of trapezium shaped pipe at a height of 1117mm from the base. 7 2 obtuse L shaped pipes are connected to the hinge supporter by the bushes. Bushes are welded at the upper portion of the obtuse L shaped pipe, Lower portion of obtuse L shaped pipe is welded with rectangular pipe of length 705mm, radius 124mm and short length 137mm. 8 On rectangular pipe standing pad are tightly screwed. Standing pad (foot rest) can be of plastic or metal. 9 Triangular hinge supporter are welded to the hinge supporter to provide better strength. Note : All the movable joints have a PIN BEARING in between, tightened with the Allen bolt poly drive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can't be opened until they will be broken.

TRIPLE HIP TWISTER : Providing and fixing including one year Warranty with free maintenance; MACHINE PARTS DESCRIPTION OF TRIPE HIP TWISTER : 1 Mounting Plate 2 Center Pillar 3 Plastic Cap 4 Circular Handle 5 Connecting Rod 6 Floor Rest Pipe 7 Standing Pad FOUNDATION OF MACHINE IS CEMENTED AND BOLTED WITH BASE CHANNEL AND CIRCULAR MOUNTING PLATE WHICH DIMENSION IS BELOW : 1 Measurement of base channel is 3'x6"x2" 2 Circular mounting plate's diameter 233mm and thickness is 8mm. 4 hole on this plate at 90 degrees which P.C.D. is 170mm. Hole diameter is 20mm. MACHANICAL DIMENSION AND MEASUREMENT OF MACHINE ARE FOLLOWING : 1 A circular mounting plate which diamension is same of above circular mounting plate and it is tightened with nut and bolt. 2 On this circular mounting plate a center pillar is welded. Diameter of center pillar is 114mm and height is 1288mm. 3 Plastic cap is fixed on the top of center pillar and tightened with help of screw. Diameter and height is 120mm and 69mm. 4 Circular handle is welded at the height of 1171mm from the base of circular mounting plate. OD of circular plate is 557 and ID is 493mm. Three pipe rod which diameter 32mm are welded at 120 degree. 5 Connecting rod for floor rest pad which diameter is 48mm. It is being bended after 131mm at angle of 30 degree and bending radius is 124. Bending length is 185mm. Again it is being bended at angle of 30 degree and bending radius 76. Bending length is 71mm. Three pipes of same dimensions are welded at the angle of 120 degree and collinear to 32 diameter's pipe rod of circular handle. 6 Three floor rest pipe which diameter 114mm and height 105mm and welded at linear center with each connecting rod. 7 Three plastic standing pad which diameter is 280mm and height is 36mm and attached with each floor rest with help of ball bearing which OD 60mm. All plastic standing pad and floor rest pipe is connected with shaft which diameter is 28mm. Note : All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic cap on the ends. Since plastic caps are fixed on the ends, the bolt can't be opened until they will be broken.

CHEST PRESS CUM SEATED PULLER : Dimensions :- 2000mm (Length)x710mm (Width)x2200mm (Heigth) Safe Area :- 3.0 Mtrx1.7 Mtr. Providing and fixing including one year Warranty with free maintenance; Chest press cum seated puller equipment made up of "B" class G.I. pipe of different NB. NB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. The center pipe is of 100 NB made up of "B" class G.I. pipe. The bottom welded with support of M.S. round plate of Ǿ 250mm & 10mm thickness. The connecting pipes are made up from 25NB "B" class G.I. pipe. The handle frame is made up from 32NB "B" class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 50mm O.D. and 6mm thickness as well as 50mm diameter solid bar is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB "B" class welded with M.S. round plate of Ǿ 250mm & 10mm thick. Main pipe supported with 25mmx25mm. M.S. angles of 3mm thickness and 20mmx40mm CRC square pipes of 3mm thickness. The seats and back rests are fitted on the outer frames are made up of M.S. sheet of size 330mmx300mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. Closing caps are made up of injection moulded plastic LLDPE/HDPE. Foundation cover cap is made from injection moulded plastic LLDPE/HDPE. Pins used of diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearing used are of "6205zz" & "6203zz" permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for locking is made up of A24 & A16 The powder coating done with pure polyester powder from Ackzonoble or berger paints with 60 to 70 micron thickness.

MULTI FUNCTIONAL TRAINER : (Single User) Providing and fixing including one year Warranty with free maintenance; Machine Part Description :- 1 Mounting plate 1 2 Cap 3 Handle connecting pipe 1 4 Connecting pipe 1 5 Center pillar 6 Holding pipe 1 7 Holding pipe 2 8 Movable pipe 9 Square pipes 10 Stepping plates 11 Stepper base 12 Standing plate 13 Center pipe 14 Mounting plate 2 15 Handle connecting pipe 2 16 Nylon pad 17 Hinged pipe 1 18 Hinged pipe 2

SHOULDER BUILDER : Mounting plate, Center pillar, 2 hinge holding pipe, 2 bending pipe, Cap, 2 u shapped pipes, Handles, 2 straight pipe (No.-1), Straight pipe (No.-2), Straight pipe (No.-3), Seat base pipe, Seat bending pipe, Seat, Back seat, Hinge box, Bracket holder 1 A circular mounting plate of diameter 233mm and thickness 8mm, there are 4 holes on this plate at 90 degrees which is P.C.D. 17mm, hole diameter is 20mm. 2 On circular mounting plate a center pillar is welded. Diameter of the center pillar is 119mm and height is 1838mm. 3 Cap is fixed on the top of the pillar with rivets. 4 At 1528mm vertical distance-2 hinges holding pipes are welded in opposite directions. Hinge holding pipes have clear hole for screw at 177mm distance. 5 Bending pipes are welded to the hinge holding pipes and the center pillar to provide mechanical strength to the hinge holding pipe. 6 Hinge box is fitted to the hinge holding pipes with a steel screw and bush. Hinge Box has a clear hole at the base. 7 U shaped pipes are welded at the upper part of the hinge box. 8 At the opening end of the U shaped pipe, handles are fitted with steel screw. 9 Straight pipe No. 1 is fitted to the hinge box at the base with Pin Bearing. 10 Lower end of the straight pipe No. 1 is fitted to straight pipe with a pin bearing. 11 Straight pipe No. 2 and No. 3 are joined to the center pillar and seat base pipe one over the other respectively with a gap of 490mm, through bracket jointers, which are welded to the centre pillar and seat base pipe also. 12 Seat base pipe is connected with straight pipe No. 2 and No. 3 with pin bearing. 13 Over seat base pipe a seat bending pipe is welded. 14 Seat and back seat are fitted on the seat bending pipe with pin bearing. These seats are of plastic. Note :- All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic caps on the ends. Since plastic caps are fixed on the ends, the bolt can't be opened until they will be broken.

CYCLE : Dimensions :- 1570mm (Length) x 570mm (Width) x 900mm (Height) Safe Area :- 2.5 Mtr x 1.5 Mtr Providing and fixing including one year Warranty with free maintenance; Cycle equipment made from "B" class G.I. pipe of different NB (NB stands for Nominal Bore size i.e. Internal Diameter of pipe in millimeters) The main frame of 50 NB made from "B" class G.I. pipes. M.S. round plate of Ǿ 300mm & 10mm thickness used to form a paddle assembly. The handle frame is of 25 NB made from "B" class G.I. pipe. The seat and back rests are fitted on the outer frames are made up of M.S. sheet of size 330mmx300mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "B" class welded with M.S. round plate of Ǿ 250mm & 10mm thick main pipe supported with 25x25mm M.S. angles of 3mm thickness and 20mmx40mm CRC square pipes of 3mm thickness. Closing caps are made up of injection mounlded plastic LLDPE/HDPE. Pins used of Diameter 25mm are made up from SAE 8620 bright material. Pins used of Diameter 13mm are made up from ENB material with CRCA pipe 20x20mm of thickness 3.00mm for paddle assembly. The bearing used are 6001zz & 6205zz permanent lubricated sealed sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The circlip used for assembly are of A24 type. The powder coating done with pure polyester powders from Ackzonoble or berger paints with 60 to 70 micron thickness.

Supply and fixing of Instruction board of size 4'x6' made of digital vinyl print with gloss lamination & pasted on 3mm ACP sheet fixed over 2.0 mm thick MS sheet, framed on 32 mm dia MS pipe, supported on 50 mm dia MS pipe which goes 600mm below ground level with hold fast including welding and painting. Design and drawing as per photograph no. 13, all complete under directions of Engineer-in-charge.

Annual Maintenance of all open air gym equipments fixed at various parks for a period of 3 years (After one year free maintenance) including replacing of any or all damaged parts and running satisfactory in all respect. Maintenance payments shall be made proportionately for Half yearly. For first Year (lumpsum amount to be quoted)

Annual Maintenance of all open air gym equipments fixed at various parks for a period of 3 years (After one year free maintenance) including replacing of any or all damaged parts and running satisfactory in all respect. Maintenance payments shall be made proportionately for Half yearly. For Second Year (lumpsum amount to be quoted)

Annual Maintenance of all open air gym equipments fixed at various parks for a period of 3 years (After one year free maintenance) including replacing of any or all damaged parts and running satisfactory in all respect. Maintenance payments shall be made proportionately for Half yearly. For Third Year (lumpsum amount to be quoted)