Public Works Department Tender

Providing and laying controlled cement concrete for cement concrete pavements including mixing and vibrations concrete with necessary needle vibrators and surface with screed board vibrating complete in all respect with stone aggregate (crusher broken) including anti-skid textured finish to required camber/ superelevation and grade including curing etc. as per specification with cement concrete M-30 grade

Cutting of construction joint/ longitudinal joint 4 to 6 mm. wide & 75 to 100 mm deep using mechanical concrete cutter including cost of diamond bit cutting wheel and filling of bitumen sealing compound in groove including cost of sealing compound.

Providing & erecting typical Cititzens infromation Board as per approved drawing & specification made of two MS Sheet of 1.6 mm thick each of xize 900mm x 750mm stiffended by angle iron 25mm x 25mm x 3mm all around the plate and plates fixed on frame of 75mm dia pipe of 12 swg sheet ( vertical post 3050mm with angle holdfasts and horizontal member 900mm) to be joined by 5mm thick MS plate at 12 places ( 65mm x 50 mm) duly embedded in cement concrete M-15 grade of block of 600mm x 600mm x 750 mm size below ground level as per enclosed drawings & as directed by engineer-in charge. All MS will by stove enameled on both side lettering figuring and border will be with ready mixed symtheic enamel paint of superior quality in required shade and colour etc. complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and and technical specifications.

Providing and laying of hot applied thermoplastic compound inclusive type I reflectrosing glass beads as per table 800-3, 800-4 applied in uniform thickness of at least 2.5 mm and spread uniformly with reflectorising glass beads type II in addition @ 250 gms per Sqm with a road marking machine as per IRC: 35 complete with traffic diversion arrangement as per MORTH specification clause 803.4.

Raised Pavment Marker ( Cats Eyes): Supplying and Fixing of Molded Shank Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 – DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 700 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer’s recommendation and complete as directed by the engineer.

Supply & fixing of Direction and place identification sign board made out of 2 mm thick M.S. sheet framed to angle iron 40x40x5 mm and two vertical posts of angle iron of size 65x65x6 mm 3 meter long with hold fasts, stove enameled paint reflective letter symbol complete of size. :(a) 150 x 120 cm.

(02) Repair of CC Road work From Nagarpalika washroom(Jodhpuriya Gate) to Bilariya gate :- Dismantling upto 1.5m in foundation and/or 1.5 m above ground level including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material, and stacking serviceable material with in a lead of 1000m. [MoRTH Specification clause 202] Concrete By mechanical Means.Cement concrete grade M-15 & M-20

Construction of dry lean cement concrete sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm , aggregate cement ratio not to exceed 15:1 , aggregate gradation after blening to be as per Table 600-1, cement content not to be less than 150 Kg/Cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant as per mix design, transported to site, laid with a hydrostatic paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing complete as per MoRTH specification clause 601.

Providing and laying controlled cement concrete for cement concrete pavements including mixing and vibrations concrete with necessary needle vibrators and surface with screed board vibrating complete in all respect with stone aggregate (crusher broken) including anti-skid textured finish to required camber/ superelevation and grade including curing etc. as per specification with cement concrete M-30 grade

Cutting of construction joint/ longitudinal joint 4 to 6 mm. wide & 75 to 100 mm deep using mechanical concrete cutter including cost of diamond bit cutting wheel and filling of bitumen sealing compound in groove including cost of sealing compound.

Supply & fixing of Direction and place identification sign board made out of 2 mm thick M.S. sheet framed to angle iron 40x40x5 mm and two vertical posts of angle iron of size 65x65x6 mm 3 meter long with hold fasts, stove enameled paint reflective letter symbol complete of size. :(a) 150 x 120 cm.

(03) BT Road from House of Rana Ramji (Bera Astaliya) to Prakash Ji Plot :- Providing and applying tack coat on the prepared surface ,with bitumen emulsion as per IS : 8887 & manufacturer’s specifications @ 2 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface )

Providing and applying tack coat on the prepared surface ,with bitumen emulsion as per IS : 8887 & manufacturer’s specifications @ 2.0 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface ) Add extra to item No. 6.2 for additional 0.1Kg per Sqm emulsion

Providing and laying bituminous concrete as per design mix on prepared surface with specified graded stone as per table 500-16 for wearing course including loading of aggregate with F.E loader and hot mixing of binder and 2% cement filler with aggregates in approved hot mix plant as per clause 6.5 of manual Transporting the mix material with tipper to paver and laying with sensor paver finisher (as per clouse 507.3.5) to the required level , grades and rolling with vibratory compactor and pneumatic tyred roller 150-250 KN,TP=0.7 Mpa, to achieve the desired density (approved by the department) excluding cost of primer/tack coat (MORTH Specification : Clause -507,112) Grade-II Bitumen @ 5.4 % of mix With lead of mix material 1 KM VG-30 grade

Supply & fixing of Direction and place identification sign board made out of 2 mm thick M.S. sheet framed to angle iron 40x40x5 mm and two vertical posts of angle iron of size 65x65x6 mm 3 meter long with hold fasts, stove enameled paint reflective letter symbol complete of size. :(a) 150 x 120 cm.

(04) BT Road from House of Sohan Lalji Prajapat to House of Sampatji (Nayapura) :- Providing and applying tack coat on the prepared surface ,with bitumen emulsion as per IS : 8887 & manufacturer’s specifications @ 2 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface )

Providing and applying tack coat on the prepared surface ,with bitumen emulsion as per IS : 8887 & manufacturer’s specifications @ 2.0 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface ) Add extra to item No. 6.2 for additional 0.1Kg per Sqm emulsion

Providing and laying bituminous macadam on prepared surface with specified graded crushed aggregate as per table 500 - 6, grading -1for base / binder course including loading of aggregates with F.E loader and heating and mixing of stone aggregate and bitumen in approved hot mix plant as per clause 6.5 of manual transporting the mixed material in tipper to paver and laying mixed material with sansor paver finisher to the required level and grade rolling by power roller & vibratory compactor to achieve the desired density (approved by the department )excluding cost of primer /tack coat [MoRTH Specification : Clause 504,112] 50-100 mm compacted thickness with 3.30% bitumen with lead of mix 20 Km.Grading II (19 mm nominal size) 3.4 % of Bitumen mix Bitumen Grade VG-30

Providing and laying open graded premix carpet 20mm thick (compacted) on prepared surface in a single course as wearing course aggregates as per Table 500-24, heating bituminous binder @ 14.6 Kg/10 Sqm.(VG-30 grade) and aggregates in Hot Mix Plant, transporting the mixed material with tipper and laying with paver finisher to the required level and grade, rolling with power roller, 8-10 tonne but excluding cost of tack and seal coat with lead for mix of material with all lead .[MORTH Specification : Clause 510,112]In approved Hot Mix Plant as per clause 6.5 of Manual, including loading of aggregates with F.E loader with VG-30 bitumen.

Providing and laying seal coat for sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall, including rolling with a smooth wheeled roller 8 - 10 tonne capacity finished to required level and grades, complete as per MORTH specification clause 511Type B - Premixed in in approved HMP as per clause 6.5 of manual having capacity 50 TPH comprising of aggregate (sand or grit) having size 2.36 mm to 180 micron @ 0.06 Cum per 10 Sqm and bitumen binder (VG-30 grade) @ 6.8 Kg / 10 sqm and laying by hydrostatic paver finisher with sensor control, including mixing, transportation, laying, rolling etc. complete - including carriage for 20 Km. lead.

Supply & fixing of Direction and place identification sign board made out of 2 mm thick M.S. sheet framed to angle iron 40x40x5 mm and two vertical posts of angle iron of size 65x65x6 mm 3 meter long with hold fasts, stove enameled paint reflective letter symbol complete of size. :(a) 150 x 120 cm.

(05) Repair of CC Road From House of Mohan Lal ji Ghanchi to House of Anna Raj Ji (Pali Darwaja road) :- Dismantling upto 1.5m in foundation and/or 1.5 m above ground level including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material, and stacking serviceable material with in a lead of 1000m. [MoRTH Specification clause 202] Concrete By mechanical Means.Cement concrete grade M-15 & M-20

Construction of dry lean cement concrete sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm , aggregate cement ratio not to exceed 15:1 , aggregate gradation after blening to be as per Table 600-1, cement content not to be less than 150 Kg/Cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant as per mix design, transported to site, laid with a hydrostatic paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing complete as per MoRTH specification clause 601.

Providing and laying controlled cement concrete for cement concrete pavements including mixing and vibrations concrete with necessary needle vibrators and surface with screed board vibrating complete in all respect with stone aggregate (crusher broken) including anti-skid textured finish to required camber/ superelevation and grade including curing etc. as per specification with cement concrete M-30 grade

Providing and laying antifriction layer of 3 ply Bituminous paper with 100 mm over-lapping in both directions.

Cutting of construction joint/ longitudinal joint 4 to 6 mm. wide & 75 to 100 mm deep using mechanical concrete cutter including cost of diamond bit cutting wheel and filling of bitumen sealing compound in groove including cost of sealing compound.

Supply & fixing of Direction and place identification sign board made out of 2 mm thick M.S. sheet framed to angle iron 40x40x5 mm and two vertical posts of angle iron of size 65x65x6 mm 3 meter long with hold fasts, stove enameled paint reflective letter symbol complete of size. :(a) 150 x 120 cm.