Public Works Department Tender

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge. In cement mortar. (B-14/14.7.3)

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M-15 grade Nominal Mix 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). (B-3/3.1.2)

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto V level in all shapes and sizes in Cement mortar 1 : 4 (1 cement : 4 coarse sand) (B-5/5.2.1)

Half brick masonry in superstructure above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 4 (1 cement : 4 coarse sand) (B-5/5.8.2)

Supplying and fixing in walls machine cut and polished stone shelves tands and in CM 1:3 with machine cut edges Sand or other approved stone 50mm thick (B-6/6.17.2)

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour) Above 3601 Cm2 Slabs. (B-7/7.5.1 (iii)

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Green / Black Above 3601 Cm2 Slabs (B-7/7.5.3 (iii)

Extra for providing edge moulding to 15-18 mm thick marble/Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. Granite work Full Edge moulding (B-7/7.6.2 (i))

Random Rubble stone masonry with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in Cement Mortar 1:6 ( 1-Cement : 6-Sand). (B-6/6.1.6)

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish 25mm thick (B-12/12.2.1)

Providing and Applying white cement based putty over plastered surface to prepare the surface even and smooth complete. New Plastered Surface (three or more coats) (B-12/12.22.1)

Carriage of Building Rubbish Stone Metal, Grit and Ballast etc. including loading and unloading complete with all lead (G-4/4.2.13)

Providing and fixing Marble stone flooring table rubbed, 15-18 mm thick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete Rajnagar 1st quality/Ageria with light spots. Above 3601 Cm2 Slabs (B-7/7.2.3)

Providing and fixing IS: 3564 marked Aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. (B-8/8.27)

Providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular/appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap. at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc, all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For fixed portion Powder coating aluminium ( min thickness of powder coating 50 micron) (B-16/16.1.1.2)

Providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular/appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap. at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc, all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For shutters builtup standard

tubular sections of openable doors, windows & ventilators including providing & fixing hinges/rollers etc. and making provision for fixing of fittings wherever required (locks shall be paid for separately). Powder coating aluminium ( min thickness of powder coating 50 micron) (B-16/16.1.2.2)

Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin, of approved brand and manufacture in paneling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Prelaminated particle board with decorative lamination on both sides. (B-16/16.4.2)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. (12.40.1)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work (B-12/12.46.1)

Supply and installation of Multi Rib Proofing/cladding Sheet Manufacture out of 0.50mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvaiumeseel (as per 150gsm zinc aluminum coated 550Mpa tuekd strength) confirming to IS: 1397/astm A-792 sheet to have wide pens 30mm high NB at 250 centre and centre width of 1020mm shets be casted with regular modified plyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate at made at to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. The sheet shall be supplied in cost one length and foe a minimum up to 12mts with all scaffolding. (B-17/17.1)

Providing & Laying Tactile tile (for vision impaired persons is standard of size 300x300x20mm and confirming to IS 1231 of 1980 (Re affirmed in 2006) in all colours & sheds further product should confirm ASTM 303 for shad resistance and DIN51099 for colour fastness etc. laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 course sand) in all shapes & patterns including grouting the joint which white cement mixer) will matching pigments etc complete is per direction of Engineer-in-charges. Grade M 30 (11.44)

Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Grade 304 16.56 (a)

Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) (16.5.2)

Providing & Fixing Aluminium composite panel of indo bond/euro/flexi bond of equivalent made 3mm that with 0.5mm thick skin& PVDF coated of approved shads for toilet door in double layer in Aluminium frame complete in all respect as per sample approved by Engineer in Charges. (16.59)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Old work (One or more coats ) (12.40.2)