Public Works Department Tender

Embankment Construction with Material Obtained from Borrow Pits (Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2)

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (incl. lead upto 42 KM & all lifts) for grading- III Material

Carriage of Sand, bajri, ballast, stone, boulders, kankar & gravelly material includind loading & unloading ( MORTH specification : 514.5 table 500.28 ) Add for each subsequnt KM. Lead Upto 42 KM.

Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.) By Manual Means Grading- II (Using Screening Type-B (11.2mm Agg.))

Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.) By Manual Means Grading- III (Using Screening Type-B (11.2mm Agg.))

Prime coat (Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.875 kg/sqm using mechanical means.)

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.275 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom

Open - Graded Premix Surfacing (Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or cut-back or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades.) Case - I: Mechanical method using Penetration grade Bitumen and HMP of appropriate capacity not less than 75 tonnes/hour .

Add exrtra for adding shreaded plastic waste as per guidelines envisaged in IRC SP:98-2013 over item of open graded premix carpet @8% of the quantity of bitumen by weight including mixing of aggregate and plastic waste in hot mix plant (The bitumen content will be as per respective clause of morth specifications.

Seal Coat (Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B seal coats) Case - II : Type B

S&F in position cut stone neatly dressed including earth work, C.C. 1:4:8 painting with enamel paint engraving letters and numerals as per IRC standard design complete. 5th Km. Stone

Ordinary Km. Stone for NH

200 M. Stone.

Providing and Erecting typical Citizens information board as per approved drawing and specifications of MoRD, made of two M.S. sheet of 1.6mm thick each of size 900 mm x 750mm stiffened by angel iron 25mm x 25mm x 3mm all around the plate and plates fixed on frame of 75mm dia pipe of 12 SWG sheet (vertical post 3050 mm with angle holdfasts and horizontal member 900mm) to be joined by 5mm thick MS plate at 12 places (65mm x 50 mm) duly embedded in C.C. M-15 Gr. of block of 600mm x 600mm x 750mm size below ground level as per enclosed drawings & as directed by Engineering - In - Charge. All MS will be stove enamelled on both side, lettering, figuring and border will be with ready mixed synthetic enamel paint of superior quality in required shade and colour etc. complete in all respect . All sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per MoRD Specification.

P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect

Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing) 90 cm equilateral triangle

Direction and Place Identification signs upto 0.9 sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)

Construction of Informatory Pedastal in 35cm thick Brick Work in CM 1:4 of size 1.20m x 1.50m above ground level with adequate foundation incl. cement plaster in CM 1:4, cement primer, painting, figuring, making of border of 75mm x 20mm in CM 1:4 etc. on both faces complete as per approved drawing and as per direction of Engineer-in-charge.

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work.) Ordinary soil Manual Means (Depth upto 3 m)

PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 mix with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

Providing and laying Random Rubble masonry in foundation upto a depth of 1.50 metres and 1.50 metres above Ground /Bed level.[MoRTH Specfication: Clause 1000/1400] Cement sand mortar 1:6

Pointing with cement mortar (1:3 ) on Stone work in substructure as per Technical specifications

Providing and laying Plain cement concrete M15 mix with stone aggregate 20mm nominal size mechnically mixed and vibrated, in foundation upto a depth of 1.50 below Ground level and or 1.50 meters above ground/bed level.

Road Markers/Road Stud with Lense Reflector (Providing and fixing of road stud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973)