Public Works Department Tender

Providing and erecting direction and place identification retro - reflectorised sign as per IRC:67 made of high intensity grade sheeting exclusive of lettering, border & signs fixed over aluminium sheeting, 2 mm thick fixed on a mild steel angle iron frame 50mmx50mmx6mm supported on mild steel angle iron post 75 x 75 x 6 mm upto the top of sign board, length of post from bottom of sign board is 2.85 m. upto foundation level post duly painted in black and white synthetic enamel alternate ship 30cm. wide fixed to the ground by means properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60 Cm , 60 Cm below ground level as per approved drawing & as per MORTH specifications clause 801. 180 cm. X 120 cm.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501, Using vacuum dewatering with required machinery

AR to Javiya road km 2/0 to 2/555 Earth work in excavation, including stacking/disposal of surplus material with all lifts and lead upto 495 metres, exclusive of compensation of earth [MoRTH specification : Clause 301 to 305] When excavation and loading is done mechanically using Bull Dozar, F.E.Loader and carriage is done by tipper/dumper (6T capacity).

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (incl. lead upto 1000M & all lifts) c) For Grading III Material

Providing, laying, spreading and compacting stone aggregate of specfic as per table 400-7 to Water Bound Macadam specification including spreading in uniform thickness, hand packing roll-ing with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening and binding materials to fill-up the interstices of coarse aggregates watering (with water browser) and rolling making necessary earthen bund to protect edegs, lighting, guarding, barricading and maintenance of diversion etc. [MoRTH specfication : Clause 404] ( By manual means).By Manual Means Grading III, 53 mm to 22.4 mm, @ 0.91 cum per 10 Sqm for compacted thickness of 75 mm. (Crusher broken) Stone screening type 'B'Stone screening type 'B'

Providing and erecting direction and place identification retro - reflectorised sign as per IRC:67 made of high intensity grade sheeting exclusive of lettering, border & signs fixed over aluminium sheeting, 2 mm thick fixed on a mild steel angle iron frame 50mmx50mmx6mm supported on mild steel angle iron post 75 x 75 x 6 mm upto the top of sign board, length of post from bottom of sign board is 2.85 m. upto foundation level post duly painted in black and white synthetic enamel alternate ship 30cm. wide fixed to the ground by means properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60 Cm , 60 Cm below ground level as per approved drawing & as per MORTH specifications clause 801. 180 cm. X 120 cm.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501, Using vacuum dewatering with required machinery

Kalapura to bhimeshwar ka Goliya road km 0/0 to 2/500 Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth upto 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material upto a lead of 1000m including removal and disposal of top organic soil not exceeding in 150 mm thickness as per MORTH specification clause 201 By mechanical Means . In area of light jungle

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (incl. lead upto 1000M & all lifts) c) For Grading III Material

Providing, laying, spreading and compacting stone aggregate of specfic as per table 400-7 to Water Bound Macadam specification including spreading in uniform thickness, hand packing roll-ing with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening and binding materials to fill-up the interstices of coarse aggregates watering (with water browser) and rolling making necessary earthen bund to protect edegs, lighting, guarding, barricading and maintenance of diversion etc. [MoRTH specfication : Clause 404] ( By manual means).By Manual Means Grading III, 53 mm to 22.4 mm, @ 0.91 cum per 10 Sqm for compacted thickness of 75 mm. (Crusher broken) Stone screening type 'B'Stone screening type 'B'

Providing and applying primer coat over prepared surface or granular base with bitumen emulsion as per IS: 8887 & manufacturer’s specifications @ 8.5 kg /10 sqm with a self propelled of towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI 502,112 ( Including cleaning of road surface )

Providing and applying tack coat on the prepared surface ,with bitumen emulsion as per IS : 8887 & manufacturer’s specifications @ 2.75 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface

Providing and laying open graded premix carpet 20mm thick (compacted) on prepared surface in a single course as wearing course aggregates as per Table 500-23, heating bituminous binder @ 14.6 Kg/10 Sqm.(VG-30 grade) and aggregates in Hot Mix Plant, transporting the mixed material with tipper and laying with paver finisher to the required level and grade, rolling with power roller, 8-10 tonne but excluding cost of tack and seal coat with lead for mix of material 1 Km.[MORTH Specification : Clause 511,112]In approved Hot Mix Plant as per clause 6.5 of Manual, including loading of aggregates with F.E loader with VG-30 bitumen.

Providing and laying seal coat for sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall, including rolling with a smooth wheeled roller 8 - 10 tonne capacity finished to required level and grades, complete as per MORTH specification clause 513 Type B - Premixed in in approved HMP as per clause 6.5 of manual having capacity 50 TPH comprising of aggregate (sand or grit) having size 2.36 mm to 180 micron @ 0.06 Cum per 10 Sqm and bitumen binder (VG-30 grade) @ 6.8 Kg / 10 sqm and laying by hydrostatic paver finisher with sensor control, including mixing, transportation, laying, rolling etc. complete - including carriage for 1 Km. lead.

Providing and erecting direction and place identification retro - reflectorised sign as per IRC:67 made of high intensity grade sheeting exclusive of lettering, border & signs fixed over aluminium sheeting, 2 mm thick fixed on a mild steel angle iron frame 50mmx50mmx6mm supported on mild steel angle iron post 75 x 75 x 6 mm upto the top of sign board, length of post from bottom of sign board is 2.85 m. upto foundation level post duly painted in black and white synthetic enamel alternate ship 30cm. wide fixed to the ground by means properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60 Cm , 60 Cm below ground level as per approved drawing & as per MORTH specifications clause 801. 180 cm. X 120 cm.

Providing and erecting direction and place identification retro - reflectorised sign as per IRC:67 made of high intensity grade sheeting exclusive of lettering, border & signs fixed over aluminium sheeting, 2 mm thick fixed on a mild steel angle iron frame 50mmx50mmx6mm supported on mild steel angle iron post 75 x 75 x 6 mm upto the top of sign board, length of post from bottom of sign board is 2.85 m. upto foundation level post duly painted in black and white synthetic enamel alternate ship 30cm. wide fixed to the ground by means properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60 Cm , 60 Cm below ground level as per approved drawing & as per MORTH specifications clause 801. Double angle post 90 cm. X 75 cm.

Supply & fixing of precast reinforced cement concrete M-15 grade kilometre stone of standard design as per IRC: 8-1980, fixing in position in cement concrete 1:4:8 including painting and printing etc. Ordinary km stone for

Supply & fixing of precast reinforced cement concrete M-15 grade kilometre stone of standard design as per IRC: 8-1980, fixing in position in cement concrete 1:4:8 including painting and printing etc. 200 m stone (precast)

Providing and fixing of retro- reflectorised inclusive cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting lettering, border & signs fixed over aluminium sheeting, 1.5 mm thick, fixed on mild steel angle iron frame 50mmx50mmx6mm supported on a mild steel angle iron post 75mmx75mmx6mm upto the top of sign board, length of post from bottom of sign board is 2.85m. upto foundation level post duly painted in black & white synthetic enamel. fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45 Cm x 45 Cm x 60Cm, 60 cm below ground level as per approved drawing & as per MORTH specification Cl. 801. 90 Cm equilateral triangle

Providing and laying of hot applied thermoplastic compound inclusive type I reflectrosing glass beads as per table 800-3, 800-4 applied in uniform thickness of at least 2.5 mm and spread uniformly with reflectorising glass beads type II in addition @ 250 gms per Sqm with a road marking machine as per IRC: 35 complete with traffic diversion arrangement as per MORTH specification clause 803.4.

SH-31 to savidhar Hanumanji road km 0/0 to 3/00 Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth upto 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material upto a lead of 1000m including removal and disposal of top organic soil not exceeding in 150 mm thickness as per MORTH specification clause 201 By mechanical Means . In area of light jungle

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (incl. lead upto 1000M & all lifts) c) For Grading III Material

Providing, laying, spreading and compacting stone aggregate of specfic as per table 400-7 to Water Bound Macadam specification including spreading in uniform thickness, hand packing roll-ing with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening and binding materials to fill-up the interstices of coarse aggregates watering (with water browser) and rolling making necessary earthen bund to protect edegs, lighting, guarding, barricading and maintenance of diversion etc. [MoRTH specfication : Clause 404] ( By manual means).By Manual Means Grading III, 53 mm to 22.4 mm, @ 0.91 cum per 10 Sqm for compacted thickness of 75 mm. (Crusher broken) Stone screening type 'B'Stone screening type 'B'

Providing and applying primer coat over prepared surface or granular base with bitumen emulsion as per IS: 8887 & manufacturer’s specifications @ 8.5 kg /10 sqm with a self propelled of towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI 502,112 ( Including cleaning of road surface )

Providing and applying tack coat on the prepared surface ,with bitumen emulsion as per IS : 8887 & manufacturer’s specifications @ 2.75 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface

Providing and laying open graded premix carpet 20mm thick (compacted) on prepared surface in a single course as wearing course aggregates as per Table 500-23, heating bituminous binder @ 14.6 Kg/10 Sqm.(VG-30 grade) and aggregates in Hot Mix Plant, transporting the mixed material with tipper and laying with paver finisher to the required level and grade, rolling with power roller, 8-10 tonne but excluding cost of tack and seal coat with lead for mix of material 1 Km.[MORTH Specification : Clause 511,112]In approved Hot Mix Plant as per clause 6.5 of Manual, including loading of aggregates with F.E loader with VG-30 bitumen.

Providing and laying seal coat for sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall, including rolling with a smooth wheeled roller 8 - 10 tonne capacity finished to required level and grades, complete as per MORTH specification clause 513 Type B - Premixed in in approved HMP as per clause 6.5 of manual having capacity 50 TPH comprising of aggregate (sand or grit) having size 2.36 mm to 180 micron @ 0.06 Cum per 10 Sqm and bitumen binder (VG-30 grade) @ 6.8 Kg / 10 sqm and laying by hydrostatic paver finisher with sensor control, including mixing, transportation, laying, rolling etc. complete - including carriage for 1 Km. lead.

Providing and erecting direction and place identification retro - reflectorised sign as per IRC:67 made of high intensity grade sheeting exclusive of lettering, border & signs fixed over aluminium sheeting, 2 mm thick fixed on a mild steel angle iron frame 50mmx50mmx6mm supported on mild steel angle iron post 75 x 75 x 6 mm upto the top of sign board, length of post from bottom of sign board is 2.85 m. upto foundation level post duly painted in black and white synthetic enamel alternate ship 30cm. wide fixed to the ground by means properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60 Cm , 60 Cm below ground level as per approved drawing & as per MORTH specifications clause 801. 180 cm. X 120 cm.

Providing and erecting direction and place identification retro - reflectorised sign as per IRC:67 made of high intensity grade sheeting exclusive of lettering, border & signs fixed over aluminium sheeting, 2 mm thick fixed on a mild steel angle iron frame 50mmx50mmx6mm supported on mild steel angle iron post 75 x 75 x 6 mm upto the top of sign board, length of post from bottom of sign board is 2.85 m. upto foundation level post duly painted in black and white synthetic enamel alternate ship 30cm. wide fixed to the ground by means properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60 Cm , 60 Cm below ground level as per approved drawing & as per MORTH specifications clause 801. Double angle post 90 cm. X 75 cm.

Supply & fixing of precast reinforced cement concrete M-15 grade kilometre stone of standard design as per IRC: 8-1980, fixing in position in cement concrete 1:4:8 including painting and printing etc. Ordinary km stone for

Supply & fixing of precast reinforced cement concrete M-15 grade kilometre stone of standard design as per IRC: 8-1980, fixing in position in cement concrete 1:4:8 including painting and printing etc. 200 m stone (precast)

Providing and fixing of retro- reflectorised inclusive cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting lettering, border & signs fixed over aluminium sheeting, 1.5 mm thick, fixed on mild steel angle iron frame 50mmx50mmx6mm supported on a mild steel angle iron post 75mmx75mmx6mm upto the top of sign board, length of post from bottom of sign board is 2.85m. upto foundation level post duly painted in black & white synthetic enamel. fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45 Cm x 45 Cm x 60Cm, 60 cm below ground level as per approved drawing & as per MORTH specification Cl. 801. 90 Cm equilateral triangle

Providing and laying of hot applied thermoplastic compound inclusive type I reflectrosing glass beads as per table 800-3, 800-4 applied in uniform thickness of at least 2.5 mm and spread uniformly with reflectorising glass beads type II in addition @ 250 gms per Sqm with a road marking machine as per IRC: 35 complete with traffic diversion arrangement as per MORTH specification clause 803.4.