Public Works Department Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Costs
EMD
₹ 6,32,860Document Cost
₹ 2,000Tender Fee
₹ 1,000
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_CEPWD_302612_2Bid Award Id
ViewTender No
NIT-10/2022-23 PWD CIRCLE BHILWARATender Authority
Public Works Department ViewPurchaser Address
-Website
http://http://pwd.rajasthan.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured).Grading as per MoRTH specification : Table 400-1, 400-2 with CBR value not less than 15.ii)To achieve 95% Proctor density.
1245
-
167
Providing, laying, spreading and compacting crushed graded stone aggregate of as per table 400-10 and 400-11 to Wet Mix Macadam specification including premixing the material with water to OMC in mechnical mixer as per approved design mix, carriage of mixed material by Tipper to site, laying in uniform layers with motor grader/F.E. Loader/paver finisher in sub base / base course on a well prepared under base and compacting with vibratory roller to achieve the desired density including lighting, guarding, barricading and maintance of diversion etc. (MoRTH specification : Clause 406) by mechanical means with all lead
1649.63
-
1008
Providing and applying primer coat over prepared surface or granular base with bitumen emulsion as per IS: 8887 & manufacturer’s specifications @ 8.5 kg /10 sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures including cleaning of road surface as per MoRTH specification CIause- 502,112
15562.5
-
30.5
Providing and applying tack coat with bitumen emulsion on the prepared surface including cleaning as per IS : 8887 & manufacturer’s specifications @ 2.75 kg /10sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification CI.503,112
15562.5
-
10
Providing and laying bituminous macadam on prepared surface with specified graded crushed aggregate as per table 500 - 4, for base/binder course including loading of aggregates with F.E. loader and heating and mixing of stone aggregate and bitumen (including cost of antistripping compound wherever required) in hot mix plant, transporting the mixed material in tipper to paver and laying mixed material with sensor paver finisher to the required level and grade, rolling by power roller & vibratory compactor to achieve the desired density (as per job mix formula approved by the department )excluding cost of primer /tack coat [MoRTH Specification : Clause 504,112] with 3.30% bitumen with all lead..For grading-1 (layer thickness above 75mm).using bitumen grade (VG-30)
622.5
-
4511
20mm thick open-graded premix carpet using bituminous (Viscosity grade/ Modified Bitumen) binder using plastic waste Providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2mm to 5.6mm aggregates either using penitration grade bitumen or emulsion to required line, grade and level to serve as waering course on a previously prepared base, including mixing of aggregate and plastic waste cutting in a hot mix plant, laying and rolling with a three wheel 80-100 KN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per MoRD specification Clause 508. Bitumen VG-30 (By mechnical means) Waste Plastic-8% of bitumen
15562.5
-
126
Providing and applying premixed seal coat type "B" comprising of thin application of fine aggregate (0.06 Cum. per 10 Sqm) premix with 6.8 Kg. per 10 sqm bitumen binder (including cost of antistripping compound, wherever required) in mini hot mix plant 6-10 TPH and laying and rolling with power roller 8-10 tonne including all lead of mix material [MORTH Specification : Clause 513] with all lead b) with bitumen grade VG-30
15562.5
-
34.5
(B) CC Pavement
Earth work in excavation in foundation trenches etc.in drains and channels etc. not exceeding 2m.depth, including dress-sing of bottom and sides of trenches, stacking the excavated soil 3m clear from the edge of excavation including disposal of surplus soil as directed within a lead of 1000 metres [MoRTH Specification : Clause 301,304] Ordinary Soil
60.75
-
57
Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured).
Grading as per MoRTH specification : Table 400-1, 400-2 with CBR value not less than 15
To achieve 95% Proctor density
45.38
-
167
Construction of dry lean cement concrete sub- base over a prepared sub - grade with coarse and fine aggregate conforming to IS : 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15 : 1, aggregate gradation after blending to be as per Table 600 -1, cement content not to be less than 150 Kg/Cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant as per mix design, transported to site, laid with a hydrostatic paver with electronic sensor, compacting with 8 -10 tonne vibratory roller, finishing and curing complete as per MoRTH specification clause 601.
18.75
-
2018
Providing, laying & fixing in position RCC spun or hume pipes ISI marked with proper jointing in required slope packed in the gasket of hume or spun yarn and neatly finished with rich grout of cement moratar 1:3 or having flexible rubber ring joint made with prefectly air and water tight including testing of joints as per MoRTH Specfication : Clause : 1000 & 2900 NP - 3, 300 mm dia
80
-
750
Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.
28.13
-
5432
(C) Road Furniture
S & F in position precast R.C.C. stone (M-15 mix) of standard IRC design including finishing in cement sand mortar 1:3, painting with enamel paint, printing letters and numerals etc. complete (MoRTH specifications clause : 800).
-
-
-
Ordinary km stone
5
-
1091
200 m stone
18
-
309
Supply of direction and place identification sign boards made out of 2mm thick sheet framed to angle iron 40 x 40 x 5 mm and two vertical posts of angle size 65 x 65 x 6 mm, 3 m long with hold fasts, stove enamelled paint and reflective letters,numerals,symbols etc. complete of size :
900 x 600 mm
8
-
2387
Supply of cautionary/warning refelective sign boards made out of 2mm thick M.S. sheet as per IRC - 67 (latest revision), stove enamelled and refelective symbol fixed on angle iron of size 65 x 65 x 6 mm of 3 m long.
900 mm equilateral triangle
14
-
1418
Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete.
-
-
-
For single post
2
-
546
For double post
2
-
900
P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect
1
-
7838
Providing and laying of hot applied thermo plastic compound inclusive of type-1 reflectorising glass beads as per table 800.3, 800.4 applied in uniform thickness of at least 2.5 mm and spread uniformlywith reflectorising glass beads type-2 in addition @ 250 gm/scm with a road marking machine as per IRC : 35 complete with traffic diversion arrangement as per MoRTH specification clause 803.4.
444.25
-
464
Supply of Cat's Eye made of aluminium alloy size 75 x 100 x 22 mm having 21 bi-convex lenses embedded in circular disk of ABS plastic on each side.
246
-
210
Fixing of cat's eyes on road surface/walls including transportation, excavation etc. complete.
246
-
60
PART 'II' Dand ka Khera (Ruppura) se Barasani Via Malumpura km 0/0 to 3/500 (A) Road Work
Clearing and grubbing road land including uprooting rank vegetation, grass, bush, shrubs, saplings and trees of girth upto 300mm, removal of stumps, disposal of unserviceable material and stacking of serviceable material upto 1000 m from road boundry as per MoRTH Specification : 201
By Mechanical Means
In area of light jungle
1.87
-
9712
Construction of Embankment with Material Obtained from Borrow Pits.Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5.with lead 50 mtr to - 500mtr
9345
-
78
Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured).Grading as per MoRTH specification : Table 400-1, 400-2 with CBR value not less than 15.ii)To achieve 95% Proctor density.
3785.18
-
167
Providing, laying, spreading and compacting crushed graded stone aggregate of as per table 400-10 and 400-11 to Wet Mix Macadam specification including premixing the material with water to OMC in mechnical mixer as per approved design mix, carriage of mixed material by Tipper to site, laying in uniform layers with motor grader/F.E. Loader/paver finisher in sub base / base course on a well prepared under base and compacting with vibratory roller to achieve the desired density including lighting, guarding, barricading and maintance of diversion etc. (MoRTH specification : Clause 406) by mechanical means with all lead
1892.82
-
1008
Providing and applying primer coat over prepared surface or granular base with bitumen emulsion as per IS: 8887 & manufacturer’s specifications @ 8.5 kg /10 sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures including cleaning of road surface as per MoRTH specification CIause- 502,112
12618.75
-
30.5
Providing and applying tack coat with bitumen emulsion on the prepared surface including cleaning as per IS : 8887 & manufacturer’s specifications @ 2.75 kg /10sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification CI.503,112
12618.75
-
10
Providing and laying bituminous macadam on prepared surface with specified graded crushed aggregate as per table 500 - 4, for base/binder course including loading of aggregates with F.E. loader and heating and mixing of stone aggregate and bitumen (including cost of antistripping compound wherever required) in hot mix plant, transporting the mixed material in tipper to paver and laying mixed material with sensor paver finisher to the required level and grade, rolling by power roller & vibratory compactor to achieve the desired density (as per job mix formula approved by the department )excluding cost of primer /tack coat [MoRTH Specification : Clause 504,112] with 3.30% bitumen with all lead..For grading-1 (layer thickness above 75mm).using bitumen grade (VG-30)
630.94
-
4511
Providing and laying open graded premix carpet 20 mm thick (compacted) on prepared surface in a single course as wearing course, aggregates as per Table 500-23, heating bituminous binder @ 14.6 Kg/10 Sqm. and aggregates in Hot Mix Plant (including cost of antistripping compound, wherever required), transporting the mixed material with tipper and laying with paver finisher to the required level and grade, rolling with power roller 8 - 10 tonne but excluding cost of tack and seal coat with lead for mix of material 1 km. (MoRTH Specification : Clause 511,112) with all lead In Hot Mix Plant 40-60 TPH, including loading of aggregates with F.E loader. b) with bitumen grade VG-30
12618.75
-
98
Providing and applying premixed seal coat type "B" comprising of thin application of fine aggregate (0.06 Cum. per 10 Sqm) premix with 6.8 Kg. per 10 sqm bitumen binder (including cost of antistripping compound, wherever required) in mini hot mix plant 6-10 TPH and laying and rolling with power roller 8-10 tonne including all lead of mix material [MORTH Specification : Clause 513] with all lead b) with bitumen grade VG-30
12618.75
-
34.5
(B) CC Pavement
Earth work in excavation in foundation trenches etc.in drains and channels etc. not exceeding 2m.depth, including dress-sing of bottom and sides of trenches, stacking the excavated soil 3m clear from the edge of excavation including disposal of surplus soil as directed within a lead of 1000 metres [MoRTH Specification : Clause 301,304] Ordinary Soil
589.28
-
57
Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured).
Grading as per MoRTH specification : Table 400-1, 400-2 with CBR value not less than 15
To achieve 95% Proctor density
585.64
-
167
Construction of dry lean cement concrete sub- base over a prepared sub - grade with coarse and fine aggregate conforming to IS : 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15 : 1, aggregate gradation after blending to be as per Table 600 -1, cement content not to be less than 150 Kg/Cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant as per mix design, transported to site, laid with a hydrostatic paver with electronic sensor, compacting with 8 -10 tonne vibratory roller, finishing and curing complete as per MoRTH specification clause 601.
181.88
-
2018
Providing, laying & fixing in position RCC spun or hume pipes ISI marked with proper jointing in required slope packed in the gasket of hume or spun yarn and neatly finished with rich grout of cement moratar 1:3 or having flexible rubber ring joint made with prefectly air and water tight including testing of joints as per MoRTH Specfication : Clause : 1000 & 2900 NP - 3, 300 mm dia
165
-
750
Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.
363.75
-
5432
(C) Road Furniture
S & F in position precast R.C.C. stone (M-15 mix) of standard IRC design including finishing in cement sand mortar 1:3, painting with enamel paint, printing letters and numerals etc. complete (MoRTH specifications clause : 800).
-
-
-
Ordinary km stone
5
-
1091
200 m stone
15
-
309
Supply of direction and place identification sign boards made out of 2mm thick sheet framed to angle iron 40 x 40 x 5 mm and two vertical posts of angle size 65 x 65 x 6 mm, 3 m long with hold fasts, stove enamelled paint and reflective letters,numerals,symbols etc. complete of size :
900 x 600 mm
10
-
2387
Supply of cautionary/warning refelective sign boards made out of 2mm thick M.S. sheet as per IRC - 67 (latest revision), stove enamelled and refelective symbol fixed on angle iron of size 65 x 65 x 6 mm of 3 m long.
900 mm equilateral triangle
18
-
1418
Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete.
-
-
-
For single post
1
-
546
For double post
1
-
900
P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect
1
-
7838
Providing and laying of hot applied thermo plastic compound inclusive of type-1 reflectorising glass beads as per table 800.3, 800.4 applied in uniform thickness of at least 2.5 mm and spread uniformlywith reflectorising glass beads type-2 in addition @ 250 gm/scm with a road marking machine as per IRC : 35 complete with traffic diversion arrangement as per MoRTH specification clause 803.4.
632.9
-
464
Supply of Cat's Eye made of aluminium alloy size 75 x 100 x 22 mm having 21 bi-convex lenses embedded in circular disk of ABS plastic on each side.
442
-
210
Fixing of cat's eyes on road surface/walls including transportation, excavation etc. complete.
442
-
60
(C) CD Works
Earth work in excavation in foundation trenches etc.in drains and channels etc. not exceeding 2m.depth, including dress-sing of bottom and sides of trenches, stacking the excavated soil 3m clear from the edge of excavation including disposal of surplus soil as directed within a lead of 1000 metres [MoRTH Specification : Clause 301,304] .Hard soil mixed with kankarboulder etc.above 20%
721.83
-
94
Providing and laying mechanically mixed and vibrated Cement Concrete in foundation upto a depth of 1.5 metres below ground level and 1.50 metres above Ground/Bed level as per MoRTH Specification : Clause 1000 & 1700
P.C.C. 1:4:8 mix with crushed stone aggregate 20 mm nominal size.
50.68
-
2210
Providing and laying stone masonry work in cement mortar 1:3 with mechanical mixer for foundation (any level) complete including all scaffolding etc. but excluding pointing and plastering as per drawing and technical specification as per MoRTH Specification : Section 1000,1400 Random rubble masonry
457.83
-
2145
Providing and laying Plain cement concrete mix with stone aggregate 20 mm nominal size mechnically mixed and vibrated in foundation up to a depth of 1.50 metres below ground level and/or 1.50 metres above ground/bed level as per MoRTH specification : clause 1000 & 1700. with all lead. P.C.C. grade M-15 in foundation & plinth upto 1.5 mtr. from ground level
187.34
-
2448
Providing Cement plaster 12mm thick in cement mortar 1:3 at all levels as per MoRTH Specfication: Clause:1000 & 1300
488.75
-
127
Providing, laying & fixing in position RCC spun or hume pipes ISI marked with proper jointing in required slope packed in the gasket of hume or spun yarn and neatly finished with rich grout of cement moratar 1:3 or having flexible rubber ring joint made with prefectly air and water tight including testing of joints as per MoRTH Specfication : Clause : 1000 & 2900
NP - 3 1000 mm dia
135
-
3850
PART 'III' A/R Sapola Km 0/0 to 5/0 (A) Road Work
Clearing and grubbing road land including uprooting rank vegetation, grass, bush, shrubs, saplings and trees of girth upto 300mm, removal of stumps, disposal of unserviceable material and stacking of serviceable material upto 1000 m from road boundry as per MoRTH Specification : 201
By Mechanical Means
In area of light jungle
2.95
-
9712
Dismantling of flexible pavements and disposal of dismantled materials upto a lead of 1000 metres, scaking serviceable and unserviceable materials separately as per MoRTH specification claue : 202.By Mechanical Means.Bituminous courses
232
-
105
Construction of Embankment with Material Obtained from Borrow Pits.Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5.with lead 50 mtr to - 500mtr
200
-
78
Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured).Grading as per MoRTH specification : Table 400-1, 400-2 with CBR value not less than 15.ii)To achieve 95% Proctor density.
2209.5
-
167
Providing, laying, spreading and compacting crushed graded stone aggregate of as per table 400-10 and 400-11 to Wet Mix Macadam specification including premixing the material with water to OMC in mechnical mixer as per approved design mix, carriage of mixed material by Tipper to site, laying in uniform layers with motor grader/F.E. Loader/paver finisher in sub base / base course on a well prepared under base and compacting with vibratory roller to achieve the desired density including lighting, guarding, barricading and maintance of diversion etc. (MoRTH specification : Clause 406) by mechanical means with all lead
1859.66
-
1008
Providing and applying primer coat over prepared surface or granular base with bitumen emulsion as per IS: 8887 & manufacturer’s specifications @ 8.5 kg /10 sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures including cleaning of road surface as per MoRTH specification CIause- 502,112
18412.5
-
30.5
Providing and applying tack coat with bitumen emulsion on the prepared surface including cleaning as per IS : 8887 & manufacturer’s specifications @ 2.75 kg /10sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification CI.503,112
18412.5
-
10
Providing and laying bituminous macadam on prepared surface with specified graded crushed aggregate as per table 500 - 4, for base/binder course including loading of aggregates with F.E. loader and heating and mixing of stone aggregate and bitumen (including cost of antistripping compound wherever required) in hot mix plant, transporting the mixed material in tipper to paver and laying mixed material with sensor paver finisher to the required level and grade, rolling by power roller & vibratory compactor to achieve the desired density (as per job mix formula approved by the department )excluding cost of primer /tack coat [MoRTH Specification : Clause 504,112] with 3.30% bitumen with all lead..For grading-1 (layer thickness above 75mm).using bitumen grade (VG-30)
618.66
-
4511
20mm thick open-graded premix carpet using bituminous (Viscosity grade/ Modified Bitumen) binder using plastic waste Providing, laying and rolling of open-graded premix carpet of 20mm thickness composed of 13.2mm to 5.6mm aggregates either using penitration grade bitumen or emulsion to required line, grade and level to serve as waering course on a previously prepared base, including mixing of aggregate and plastic waste cutting in a hot mix plant, laying and rolling with a three wheel 80-100 KN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per MoRD specification Clause 508. Bitumen VG-30 (By mechnical means) Waste Plastic-8% of bitumen
18412.5
-
126
Providing and applying premixed seal coat type "B" comprising of thin application of fine aggregate (0.06 Cum. per 10 Sqm) premix with 6.8 Kg. per 10 sqm bitumen binder (including cost of antistripping compound, wherever required) in mini hot mix plant 6-10 TPH and laying and rolling with power roller 8-10 tonne including all lead of mix material [MORTH Specification : Clause 513] with all lead b) with bitumen grade VG-30
18412.5
-
34.5
(B) CC Pavement
Earth work in excavation in foundation trenches etc.in drains and channels etc. not exceeding 2m.depth, including dress-sing of bottom and sides of trenches, stacking the excavated soil 3m clear from the edge of excavation including disposal of surplus soil as directed within a lead of 1000 metres [MoRTH Specification : Clause 301,304] Ordinary Soil
67.5
-
57
Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured).
Grading as per MoRTH specification : Table 400-1, 400-2 with CBR value not less than 15
To achieve 95% Proctor density
77.63
-
167
Construction of dry lean cement concrete sub- base over a prepared sub - grade with coarse and fine aggregate conforming to IS : 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15 : 1, aggregate gradation after blending to be as per Table 600 -1, cement content not to be less than 150 Kg/Cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant as per mix design, transported to site, laid with a hydrostatic paver with electronic sensor, compacting with 8 -10 tonne vibratory roller, finishing and curing complete as per MoRTH specification clause 601.
33.75
-
2018
Providing, laying & fixing in position RCC spun or hume pipes ISI marked with proper jointing in required slope packed in the gasket of hume or spun yarn and neatly finished with rich grout of cement moratar 1:3 or having flexible rubber ring joint made with prefectly air and water tight including testing of joints as per MoRTH Specfication : Clause : 1000 & 2900 NP - 3, 300 mm dia
20
-
750
Construction of un-reinforced, without Dowl Bar plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per MoRTH specification clause 602.
74.25
-
5432
(C) Road Furniture
S & F in position precast R.C.C. stone (M-15 mix) of standard IRC design including finishing in cement sand mortar 1:3, painting with enamel paint, printing letters and numerals etc. complete (MoRTH specifications clause : 800).
-
-
-
Ordinary km stone
6
-
1091
200 m stone
20
-
309
Supply of direction and place identification sign boards made out of 2mm thick sheet framed to angle iron 40 x 40 x 5 mm and two vertical posts of angle size 65 x 65 x 6 mm, 3 m long with hold fasts, stove enamelled paint and reflective letters,numerals,symbols etc. complete of size :
900 x 600 mm
6
-
2387
Supply of cautionary/warning refelective sign boards made out of 2mm thick M.S. sheet as per IRC - 67 (latest revision), stove enamelled and refelective symbol fixed on angle iron of size 65 x 65 x 6 mm of 3 m long.
900 mm equilateral triangle
16
-
1418
Installation of sign boards having the posts like mandantory, cautionary and informatory boards including excavation, fixing of posts in 300 mm dia. RCC hume pipe (IS marked) 1.20 m long, 75 cm embedded in ground, the in side of pipe shall be filled with cement concrete 1 : 4 : 8 with semi-circular hump at top, the pipe shall be painted white with enamel paint including transportation etc. complete.
-
-
-
For single post
2
-
546
For double post
2
-
900
P& F Mukhya Mantri Sadak Yojana logo for roads funded by State road fund having M.S. Definition plate of 1.6mm thickness frame to steel hollow dsection of 75mm x 75mm, 2.5m long stove enamelled paint with hold fast including paint logo as per approved design and colours. The logo shall be made out of 1.6mm thick circular plate fix on 1200mm x 150mm rectangular steel base plate 1.6mm thick, the base of circular shall be plain at the junction of base plate. The size of definition plate shall be 1500x600mm and embedding the posts by M-15 mix C.C. block 300x300x600 mm including lettering / writing and painting etc. complete in all respect
1
-
7838
Providing and laying of hot applied thermo plastic compound inclusive of type-1 reflectorising glass beads as per table 800.3, 800.4 applied in uniform thickness of at least 2.5 mm and spread uniformlywith reflectorising glass beads type-2 in addition @ 250 gm/scm with a road marking machine as per IRC : 35 complete with traffic diversion arrangement as per MoRTH specification clause 803.4.
220.13
-
464
Supply of Cat's Eye made of aluminium alloy size 75 x 100 x 22 mm having 21 bi-convex lenses embedded in circular disk of ABS plastic on each side.
102
-
210
Fixing of cat's eyes on road surface/walls including transportation, excavation etc. complete.
102
-
60
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements