Public Health Engineering Department Tender

PHED O&M BSR 2020 1.1.1.2 80/90 mm

PHED O&M BSR 2020 1.1.1.3 100/110 mm

PHED O&M BSR 2020 1.1.1.4 125/140 mm

PHED O&M BSR 2020 1.1.1.5 150/160/180 mm

PHED O&M BSR 2020 1.2 Repairing of leakage in existing Distribution/ Rising /Main/ Transmission Main CI/MS/DI pipe Line up to 1.5 mtr depth of sizes as given below by digging out suitable size of pit at site of work including taking out the burst pipe from trench, dewatering and providing adequate safely arrangement at site. This will also include cutting of pipe ends, fixing of pipe piese with jointing material, tightening of CID Joints to make repair leak proof and then refiling of execavated tench / Pit / Road shall be done properly ie after a layer of 20cm with proper watering and ramming in layer for entire job contractor will use his own T&P & Labour and will arrange transportation of material required from Jen store (Required material such as pipe peice, CID joints shall be provided by department free of cost)

PHED O&M BSR 2020 1.2.1 In all Type of Soil

PHED O&M BSR 2020 1.2.1.1 80 mm

PHED O&M BSR 2020 1.2.1.2 100 mm

PHED O&M BSR 2020 1.2.1.3 125 mm

PHED O&M BSR 2020 1.2.1.4 150 mm

PHED O&M BSR 2020 VALVE 6.1 Providing, lowering, aligning, fixing in position in pipe line, CI D/F Sluice valves of approved make of following Pressure rating & dia complete, confirming to IS:14846 (amended up to date) and of following specifications: Body, Bonnet, Wedge, Gland, Thrust Plate, Cap & Hand wheel of Grey cast iron of IS:210/ FG200 Stem - SS 304 ,Body Seat ring, Wedge facing ring & Bushes - LTB2/ SS , Face to face dimensions as per IS 14846/2000 (amended up to date), All exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to IS:5660 and two coats of black Japan paint conforming toType B of IS 341or paint conforming to IS9862 or IS2932( Non-Toxic- suitable for drinking water) applied inside and outside, Flanges Drilled as per IS 1538.Nut-Bolt confirming to IS:1363 and IS: 1367/ CS/ galvanised steel.Insersion rubber of black EPDM 6mm thick . Suitable support structure as per directions of EIC. Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in- charge. Note: Rates are exclusive of tail piece/ dismantling joints and earth work

PHED O&M BSR 2020 VALVE 6.1.1 Manually Operated CI Sluice valve of Class PN-1.0

PHED O&M BSR 2020 VALVE 6.1.1.1 80 mm HW

PHED O&M BSR 2020 VALVE 6.1.1.2 100 mm HW

PHED O&M BSR 2020 VALVE 6.1.1.3 125 mm HW

PHED O&M BSR 2020 VALVE 6.1.1.3 150 mm HW

PHED O&M BSR 2020 VALVE 6.3 Providing, lowering, aligning, fixing in position in pipe line, CI double flanged swing type Non Return Valves (NRV) of approved make of following Pressure rating & dia complete, confirming to IS: 5312 (part -1)/ 2004 (amended up to date) and of following specifications: Body, Cover & disc of Grey cast iron of IS:210/ FG200. Face to face dimensions as per IS 5312 (part -1):2004 , Flanges Drilled as per IS:1538. All exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to IS:5660and two coats of black Japan paints conforming toType B of IS 341or paint conforming to IS9862 or IS2932( Non-Toxic- suitable for drinking water) applied inside and outside. Body seat ring of SS/CS Door face ring - EPDM/ Neoprene (food grade quality) ,Shaft of HTB1/ SS- AISI- 410, Hinge Malleable cast iron / SS AISI 316/410 ,Bonnet Gasket EPDM, Bush- Leaded tin Bronze/ PTET, Gasket EPDM/NBR ,Nut-Bolt as per IS:1363 and IS: 1367 (galvanised steel) ,Insersion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC including jointing & jointing material, labour, testing and commissioning along with pipeline as per Technical Specification & as per direction of Engineer-in-charge. Note: Rates are exclusive of tail piece/ dismantling joints and earth work

PHED O&M BSR 2020 VALVE 6.3.1 Class PN 1.0

PHED O&M BSR 2020 VALVE 6.3.1.1 80 mm dia

PHED O&M BSR 2020 VALVE 6.3.1.2 100 mm dia

PHED O&M BSR 2020 1.11.1 Providing and fixing of flanged/ plain ended MS Specials made from MS sheet strips of relevant IS specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level/ depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing and commissioning along with pipe line as per technical specifications and direction of Engineer-in- charge. MS pipe specials upto 600mm dia (with minimum 5mm thickness sheet)