Nuclear Fuel Complex Tender

Providing , Supplying & fixing of openable Kitchen cabinets as per drawing made of HDHMR (High Density High Mositure resistant) board with density not less than 850 Kg/m3 and screw withdrawl strength not less than 350 Kg at edges and 450 Kg at face of Action Tesla or equiavelnt including all hardware, screws and fittings of Approved make like Hettich or equilavent , complete as per below specification Shelves/Frames/Vertical Partitions :- Supplying & Fixing of frame, shelves and vertical partitions to the exisiting precast cupboards with 18mm thick HDHMR Board of make Action Tesa or equivalent overlaid with 0.8 mm thick white/balancing laminate of make Greenlam or equivalent on both sides fitted with necessary hardware and all exposed edges are covered with 2mm thick PVC tape using EVA hot melt glue at 200 degree C on the imported through feed edge banding machine etc. complete as specified and directed. Shutters & Frame:- Supply & Fxing of shutters & frame, 18mm thick HDHMR Board of make Action Tesa or equivalent overlaid with 1mm thick colour laminate make Greenlam or equivalent on exposed sides and 0.8mm thick white laminate on other side and and all exposed edges are covered with 2mm thick PVC tape using EVA hot melt glue at 200 degree C on the imported through feed edge banding machine including all hardware of Hettich/Ebco Make viz. i) steel, nickel plated hinges opening angle 105degree with hinge cover 2 Nos. for each shutter min or as per manufacturer specification. ii) Nickle Matt/Bright Crome finish Handles with min hole distance of 128 mm, 1 No for each shutter iii) Magnetic catcher , tower bolt etc. complete as specified and directed iv) PVC corner guard as per drawing. v) SS jali for shutters as per drawing. All other hardware and screws complete as specified and directed by EIC. Note :- Only clear opening dimension (LXH) of the cupboard/cabinet will be measured for payment

Providing , Supplying & fixing of openable wardrobes as per drawing made of HDHMR (High Density High Mositure resistant) board with density not less than 850 Kg/m3 and screw withdrawl strength not less than 350 Kg at edges and 450 Kg at face of Action Tesla or equiavelnt and including all hardware, screws and fittings of Approved make like Hettich or equilavent , complete as per below specification Shelves/Frames/Vertical Partitions/Boxes :- Supplying & Fixing of frame, shelves and vertical partitions to the exisiting precast cupboards with 18mm thick HDHMR Board of make Action Tesa or equivalent overlaid with 0.8 mm thick white/balancing laminate of make Greenlam or equivalent on both sides and backside fitted with necessary hardware and all exposed edges are covered with 2mm thick PVC tape using EVA hot melt glue at 200 degree C on the imported through feed edge banding machine etc. complete as specified and directed. Shutters:- Supply & Fxing of shutters & frame, 18mm thick HDHMR Board of make Action Tesa or equivalent overlaid with 1mm thick colour laminate make Greenlam or equivalent on exposed sides and 0.8mm thick white laminate on other side and and all exposed edges are covered with 2mm thick PVC tape using EVA hot melt glue at 200 degree C on the imported through feed edge banding machine including all hardware of Hettich/Ebco or equivalent Make viz. i) Steel, nickel plated soft closing hinges with hinge cover min 4 Nos for wardrobe shutter (each) and 2 nos for loft shutter (each) or as per manufacturer specification. ii) Nickle Matt/Bright Crome finish Handles with min hole distance of 192 mm for wardrobe shutter and 160 mm for loft shutter , 1 No for each shutter iii) Rail 1 No. (Hettich Chrome Gloss 9309079 or equivalent with end supports inclusive) iv) Magnetic catcher , tower bolt, locks etc. complete as specified and directed. v) SS chain for holding the shutters ( Min 1 No for each shutter ) or as per manufacturer specification. Drawers :- Supplying & Fixing ofdrawers with 12/9mm thick HDHMR Board of make Action Tesa or equivalent overlaid with 0.8 mm thick white laminate make Greenlam or equivalent on both sides and front face facia and back side with 1mm thick colour laminate make Greenlam or equivalent on exposed sides and 0.8mm thick white laminate on other side fitted with necessary hardware and all exposed edges are covered with 2mm thick PVC tape using EVA hot melt glue at 200 degree C on the imported through feed edge banding machine including all hardware of Hettich Make or equivalent viz. i) Telescopic channels (2 set) , ii) Drawer Lock (2 Nos.) , iii) Drawer Handle (2 Nos.) with min hole distance of 128 mm etc. complete as specified and directed. All other hardware and screws complete as specified and directed by EIC. Note :- Only clear opening dimension (LXH) of the cupboard will be measured for payment

Providing and fixing Matt finish stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates,flats etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts, welding etc. complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, with suitable arrangement as per approval of Engineer-incharge. Note: For payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.