Nuclear Fuel Complex Tender
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Nuclear Fuel Complex - NFC Tender
Eprocure
Opening Date7 Dec 2021
Closing Date11 Jan 2022
Tender Amount₹ 8,70,00,000
Costs
EMD
Refer DocumentsDocument Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_NFC_661497_1Bid Award Id
ViewTender No
E/630/2021Tender Authority
Nuclear Fuel Complex ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
ERECTION
4
-
-
Centrifugal pumps: Water recirculation centrifugal pumps suitable to handle water for above mentioned air flow rate.
Accessories: Flexible coupling, mounting frame, etc., MOC: Cast Iron casing with SS impeller
Drive Arrangement Suitable with VFD
(Note: VFD is covered in electrical schedule)
-
-
-
SUPPLY
4
-
-
ERECTION
4
-
-
Plumbing between Spray chamber and Pumps
Piping from spray chamber to/from the pumps. Associated pump accessories : Isolation valves at inlet & outlet, flow regulation valves, NRV/check valve, strainer, etc. Piping from battery limit is also covered in this scope . Necessary fittings : Elbows, tees, couplings, reducers fasteners, clamps.etc, MOC : GI Class B
Dwg: "C-CED/EP(AC&V)NFC(K)-147" for reference.
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
Spray Chamber internals: Supply Installation Testing & Commissioning of three bank water spraying system with header, distributers, HDPV nozzles, marine light, pipe fittings, quick fill make up water line along with float and valve, drain pipe with gate valve, etc.
MOC : GI Class-B
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
Fresh Air Filter Capacity : 2000 CFM Grade : G4 Efficiency : 90% down to 10 micron Filter Media : HDPE Size : 610x610 mm Casing : Aluminium Face guard : Wire mesh type
(Note: Necessary support structure is covered in another item)
-
-
-
SUPPLY
300
-
-
ERECTION
300
-
-
PVC Air distributer (Note: Necessary MS support structure is covered in another item).
-
-
-
SUPPLY
110
-
-
ERECTION
110
-
-
Chevron type PVC Mist eliminator
(Note: Necessary MS support structure is covered in another item).
-
-
-
SUPPLY
110
-
-
ERECTION
110
-
-
Exhaust air Fans : SISW type, backward curved, belt driven. Temperature to be considered is 50deg C. The scope also includes accessories like flexible connections at fan outlet,common base frame, vibration isolators, V-belt, guard, electrical actuator controlled volume control damper at the outlet. MS construction shall be epoxy painted. Capacity : 52800 CFM
Static Pressure: 350 mm WC
Drive Arrangement Suitable with VFD
(Note: VFD is covered in electrical schedule )
-
-
-
SUPPLY
4
-
-
ERECTION
4
-
-
Primary Exhaust air Fans : SISW type, backward curved, belt driven. Temperature to be considered is 50deg C. The scope also includes accessories like flexible connections at fan outlet,common base frame, vibration isolators, V-belt, guard, electrical actuator controlled volume control damper at the outlet. MS construction shall be epoxy painted. Static Pressure: 350 mm WC
MOC : Mild Steel
-
-
-
Capacity :3000 CFM
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
Capacity :5900 CFM
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
GI DUCTING: Duct shall be complying to IS: 277, Class IV, Grade 275 GSM.
Accessories included: Supply/Exhaust air collars, vanes, splitters, necessary MS structural members (viz. angle flanges for duct joining, lateral& longitudinal reinforcement, internal tie rods, fasteners), gaskets, sealent, etc. Duct construction shall be as per IS-655/SMACNA standrad. (Note: Necessary duct supporting/hanging structural material (MS) is covered under item)
-
-
-
18 gauge ducting, Rectangular
-
-
-
SUPPLY
160
-
-
ERECTION
160
-
-
22 Gauge, Rectangular
-
-
-
SUPPLY
1070
-
-
ERECTION
1070
-
-
18 Gauge, Circular
-
-
-
SUPPLY
150
-
-
ERECTION
150
-
-
22 Gauge, Circular
-
-
-
SUPPLY
1100
-
-
ERECTION
1100
-
-
16 Gauge for plenum
-
-
-
SUPPLY
300
-
-
ERECTION
300
-
-
SS304 Ducting: Supply/Exhaust air duct with SS304 material complying to ASTM A 240.
Accessories included: supply/exhaust air collars, vanes, splitters, necessary MS structural members (viz. angle flanges for duct joining, lateral& longitudinal reinforcement, internal tie rods, fasteners), gaskets, sealent, etc. Duct construction shall be as per IS-655/SMACNA standrad.
Thickness :22 Gauge, Type : Circular
(Note: Necessary duct supporting structural material (MS) is covered under item )
-
-
-
SUPPLY
220
-
-
ERECTION
220
-
-
Manually operated Volume Control Dampers Thickness: 16 G Thick
Dimensions: As per Requirement
Measurement: Cross Sectional Flow Area including flanges
-
-
-
Rectangular, MOC: GI
-
-
-
SUPPLY
10
-
-
ERECTION
10
-
-
Circular, MOC: GI
-
-
-
SUPPLY
10
-
-
ERECTION
10
-
-
Circular, MOC: SS 304
-
-
-
SUPPLY
4
-
-
ERECTION
4
-
-
Electrically operated Volume Control Dampers for ducting with one of the dimensions 1.0 mtr and above Thickness: 16 G Thick
Dimensions: As per Requirement
Measurement: Cross Sectional Flow Area including flanges
-
-
-
Rectangular, MOC: GI
-
-
-
SUPPLY
10
-
-
ERECTION
10
-
-
Circular, MOC: GI
-
-
-
SUPPLY
10
-
-
ERECTION
10
-
-
Actuators for electrically operated Volume Control Dampers
-
-
-
SUPPLY
10
-
-
ERECTION
10
-
-
Non Return damper MOC: SS 304
Thickness: 16 G Thick
Dimensions: As per Requirement
Measurement: Cross Sectional Flow Area including flanges
-
-
-
SUPPLY
6
-
-
ERECTION
6
-
-
Fusible link type Fire dampers
MOC: GI
Thickness: 16 G Thick
Dimensions: As per Requirement
Note: Dampers shall be CBRI tested & certified for minimum 90 minutes rating as per UL 555 Measurement: Cross Sectional Flow Area including flanges
-
-
-
SUPPLY
40
-
-
ERECTION
40
-
-
Supply Air Grills: Type : Double deflection grills/Four Way Diffusers as per layout
MOC: Extruded Aluminium Powder Coated Frame Thickness : 16 G
Accessories : Volume control Dampers
-
-
-
SUPPLY
30
-
-
ERECTION
30
-
-
Return Air diffusers
MOC: Extruded Aluminium Powder Coated Frame Thickness : 16 G
-
-
-
SUPPLY
24
-
-
ERECTION
24
-
-
MS. Structure (For General purpose): Painting : Epoxy painting with primer Scope: Duct supports, Yard Trustels for carrying ducts, supporting stand.
-
-
-
SUPPLY
9000
-
-
ERECTION
9000
-
-
MS. Structure(For retainer frames):
Painting : Epoxy painting with primer Scope: HEPA filter/ Pre Filter/ Fresh Air filter/Air Distributer/ Mist Eliminator etc
-
-
-
SUPPLY
22000
-
-
ERECTION
22000
-
-
HEPA Filters
Grade : H-14
Size: 610x 610x300 mm (Approx.)
Flow Rate: 2000 CFM
Efficiency : 99.97% down to 0.3 micron Initial Pressure Drop: 40 mmWC maximum in clean condition
Casing : 1.2 mm thick Aluminium
Media : Borosilicate Microfibre
-
-
-
SUPPLY
120
-
-
ERECTION
120
-
-
Pre-Filters
Grade : G4
Size: 610x 610 mm
Flow Rate: 2000 CFM
Efficiency : 95% down to 10 micron Initial Pressure Drop: 12 mmWC maximum in clean condition
Casing : 1.2 mm thick Aluminium
Media : Non woven Synthetic media sandwiched between 2 layers of HDPE Mesh
-
-
-
SUPPLY
120
-
-
ERECTION
120
-
-
Insulation: Type: Elastomeric closed cell structure nitrile rubber Thickness : 25 mm
Fire Rating: Class 'O'
Duct insulation - For all supply air duct running through the Sintering area plant at roof level
-
-
-
SUPPLY
700
-
-
ERECTION
700
-
-
Aluminium silicate Thermal Insulation
Thickness: 25 mm Temperature : Minimum 250 Deg C
Note: For primary exhaust system of sintering furnace system.
-
-
-
SUPPLY
150
-
-
ERECTION
150
-
-
MS Leak tight doors Size : 2.215 x1.115 m Note: For masonary type HEPA/Pre-filter chambers Refer : Drawing no C-CED/EP(AC&V)-142
-
-
-
SUPPLY
8
-
-
ERECTION
8
-
-
MODULAR PRE/HEPA FILTER CHAMBER
MOC : SS 304 Filters Qty: 4 Nos of HEPA and Prefilters each
HEPA Grade: H 14
Pre Grade : G-4with wheels confirming to HA -1120-2 of ASME AG-1 of 2012 with bank efficiency of 99.5%.
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
Modular Type Mist Eliminator
Construction : 18 G SS304 Flow rate : 5900 CFM
Type: V shape
Note: The unit is part of PV system for grinders.
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
1)Developing CAD drgs pertaining to GA, duct layout drawings as per specifications. 2)Simulation of Air flow pattern by CFD analysis using ANSYS or equivalent software. 3) Developing P&ID drgs of all ventilation systems as per schemes given 4) Assessing TAG numbers to all ventilation equipment 5)Validating of total sytem by smoke test.
-
-
-
SUPPLY
1
-
-
ERECTION
1
-
-
Design, Engineering, fabrication, transportation, Safe handling,supply, site storage, Installation, Testing & Commissioning of Fully Draw-out type Motor Control Centre for air blowers and pumps as per tender specifications
-
-
-
Sintering & Grinding PDP
4P, 800A EDO type ACB I/C-2Nos.
4P, 800A EDO type ACB B/C-1No.
3P+NL, 400A MCCBs --- 5 Nos.
3P+NL, 250A MCCBs --- 2 Nos.
18.5kW Star-Delta Starter -- 2 Nos. 11kW DOL Starter --2Nos.
-
-
-
SUPPLY
1
-
-
ERECTION
1
-
-
Damper Control Panel
4P, 63 A MCCB I/C-1Nos.
1 KW DOL starter(3Phase) - 8 Nos
1 KW DOL starter(1 Phase) - 9 Nos
3P+NL, 32A MCCB --- 1 Nos.
Damper Control Panel
4P, 63 A MCCB I/C-1Nos.
-
-
-
SUPPLY
3
-
-
ERECTION
3
-
-
Design, Engineering, fabrication, transportation, Safe handling, supply, site storage, Installation, Testing & Commissioning of Fully Draw-out type VFD Motor Control Centre for air blowers and pumps as per tender specifications
-
-
-
Sintering Area & Grindering Area Supply Air MCC panel
4P, 400A MCCB I/C-2Nos.
4P, 400A MCCB B/C-1No.
55kW VFDs --- 2 Nos.
22kW VFDs --- 2 Nos.
3P+NL, 63A MCCBs --- 2 Nos.
Sintering Area & Grindering Area Supply Air MCC panel
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
Design, Engineering, fabrication, transportation, Safe handling, supply, site storage, Installation, Testing & Commissioning of Variable Frequency Drives for air blowers and pumps as per tender specifications
132kW VFD panel
-
-
-
SUPPLY
4
-
-
ERECTION
4
-
-
Supply, installation, testing and commissioning of 1100 V grade, Aluminium Conductor, XLPE insulated and armoured FRLS cables of following sizes as per data sheet, specifications of this tender and directions of Engineer-in-Charge. including transport, all labour and materials, complete in all respects.
-
-
-
3Cx300 sqmm copper conductor
-
-
-
SUPPLY
500
-
-
ERECTION
500
-
-
4Cx 16 sqmm Al conductor
-
-
-
SUPPLY
50
-
-
ERECTION
50
-
-
Supply, installation, testing and commissioning of 1100 V grade, Copper Conductor, XLPE insulated and armoured, FRLS cables of following sizes as per data sheets, specifications of this tender and directions of Engineer-in-Charge. including transport, all labour and materials, complete in all respects.
-
-
-
3Cx120sqmm
-
-
-
SUPPLY
600
-
-
ERECTION
600
-
-
3Cx35sqmm
-
-
-
SUPPLY
700
-
-
ERECTION
700
-
-
3Cx16sqmm
-
-
-
SUPPLY
700
-
-
ERECTION
700
-
-
4Cx2.5sqmm
-
-
-
SUPPLY
1500
-
-
ERECTION
1500
-
-
Termination of XLPE insulated armoured Aluminium/Copper power cables (up to 1100 V grade) and connection of leads including the supply of single compression cable glands and heavy duty copper lugs, drilling of suitable holes in equipments for fixing purposes, including fixing of cable glands, supply and fixing of PVC shrouds, cutting and stripping of cable insulation, crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number, ferrules etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
-
-
3.5Cx 300sqmm
-
-
-
SUPPLY
8
-
-
ERECTION
8
-
-
3Cx120sqmm copper conductor
-
-
-
SUPPLY
24
-
-
ERECTION
24
-
-
3Cx35sqmm
-
-
-
SUPPLY
16
-
-
ERECTION
16
-
-
4Cx 16 sqmm Al conductor
-
-
-
SUPPLY
2
-
-
ERECTION
2
-
-
3Cx 16 sqmm copper conductor
-
-
-
SUPPLY
16
-
-
ERECTION
16
-
-
4Cx2.5sqmm copper conductor
-
-
-
SUPPLY
98
-
-
ERECTION
98
-
-
CABLE – TRAYS : Supply and installation of prefabricated hot dip galvanised steel cable trays,
fabricated out of hot rolled sheet steel with rigid welded construction ladder type with a rung as per std. tender drawing of approved make and cable tray fittings, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
-
-
-
150 mm wide Straight run cable tray.
-
-
-
SUPPLY
160
-
-
ERECTION
160
-
-
450 mm wide Straight run cable tray.
-
-
-
SUPPLY
240
-
-
ERECTION
240
-
-
Supply, fabrication and installation of 0.91 mm (20 gauge) GI sheet covers for all
sizes cable trays, including necessary hardware, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer- in-Charge.
-
-
-
SUPPLY
145
-
-
ERECTION
145
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements