Nuclear Fuel Complex Tender

Hard rock ( by chiselling or wedging or rock hammer and cutter or hydraulic splitter or controlled blasting/by using machine/ such as poclain with jack hammer or controlled blasting or by approved chemical method as directed by EIC)

Filling available excavated earth (Crushed Sand avialable inside campus) in plinth , sides of foundation etc., in layers not exceeding 20cm in depth , consolidating each deposited layer by ramming and watering , lead upto 50m and lift upto 1.5m.

Lead charges for additional lead over the initial lead of 50 m by mechanical transport, including loading, unloading, stacking, the disposable soil, rock etc., Note: Measurement of lead charges will be based on truck measurement with a deduction of voids @20% and 50% for soils and rock or debris respectively

For rock/debris lead above 1 KM upto 3KM

CONCRETE (PLAIN AND REINFORCED) :

Plain Cement Concrete 1:2:4 using Portland Pozzolana Cement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) with crushed stone sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including consolidation, finishing smooth/broom finish as applicable, curing, etc., but excluding Formwork, complete as specified and directed. Note: 1.The blended cement i.e., PPC shall not have more than 25% of pozzolanas.

Reinforced Cement Concrete by insitu mixing using Weigh Batching or RMC of Ultra Tech, Birla Ready Mix of Grade M - 30 (Minimum Cementitious Content not less than 350 Kg/Cum) up to specified level using Portland Pozzolana Cement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) with crushed stone sand and graded stone aggregates of 20mm maximum size including mixing superplasticizer of brand M/s. Fosroc, Demech, Huntsman, Pidilite, Sunanda Chemicals, Agro Chemicals, MBT in proportion as per Manufacturer's Specifications, Pumping / Lifting of concrete to the required heights, Concrete laid to proper level, profile and slope, placing concrete, consolidation, finishing, curing, etc., but excluding Formwork and reinforcement as specified and directed. Note: 1.The blended cement i.e., PPC shall not have more than 25% of pozzolanas.

Below FFL including grade slab

Above FFL

FORM WORK :

Providing centering and shuttering using 12mm thick marine plyboard at all depths and heights below and above plinth level, vertical, horizontal, inclined,circular including strutting, propping using steel pipes/acro stagging, removal, cleaning of the same for insitu reinforced cement concrete and in plain cement concrete work, pockets for machine/equipmet foundations as required including chamfers, splays, keys, wedges, nails, bracings, brackets and applying one coat of shuttering oil on all shuttering surfaces coming in contact with concrete etc., complete as directed. Note :- Plywood shall not be used for more than eight repitions.

a) Below and Upto Finish Floor Level

b) Above Finish Floor Level

REINFORCEMENT & STRUCTURAL STEEL

Supply, fabrication and erection of Reinforcement bars for Reinforced cement concrete items at and at all depths and heights below and above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more conforming to IS 1786 of Tata, Vizag,Sail, JSW make, including transport to site, loading and unloading, making fan hooks of required shape, dowels for bonding masonry, transporting steel to site, decoiling, removing of scales, straightening, cutting, bending, fixing bars with chairs, space bars wherever required, in position with two strings of 18 gauge soft drawn annealed MS binding wire inclusive of its supply etc., complete as specified and directed.

Supply, Fabrication and Erection of Structural Steel work using Rolled Steel Joists, Beams, Channels, Plates, steel tube, Rectangular section etc., at all levels above and below plinth level including supplying of steel sections and plates conforming to BIS 2062,1161 or 806 of make Vizag Steel, Tata, SAIL, Jindal Ispat or any other approved manufacturer using ingots of above manufacturer make, loading, unloading, transporting the steel to site of work, cutting, fabricating using welding/bolts, using weld rods of make D&H, Advani, Philips or its approved equivalent and/or bolts and nuts from approved source, erecting using derricks/pulleys/cranes or any suitable means, fixing in position and painting with one coat of approved red oxide zinc chromate primer and two coats of Synthetic Enamel paint as per manufacturers Specifications of make Asian Paint, Berger, Johnson and Nickelson, Nerolac, cleaning the sections /plates by suitable means, etc., complete as directed by the Engineer-in-Charge.

Using Plates /Chequered Plates including MS insert plates/ embedded plates/pipes in medium quality conforming to relevant BIS codes of required shape and size, welding anchoring legs not less than 12mm dia MS rods, placing in position in concrete while casting, including painting with one coat of approved red oxide zinc chromate primer as per drawing in line, level and plumb complete as directed. Note :- Anchoring Legs will be paid under relevant items

Supplying, fabricating, erecting and fixing in position, foundation bolts, through bolts etc. using MS rounds of make M/s Tata, Vizag Steel, Jindal or approved equivalent conforming to IS 432 and suitable nuts including threading, placing in position in concrete in level using template, providing grease and protective cover like covering with polyethelene sheet to bolts and nuts to correct levels complete and as directed by EIC.

STONE MASONRY :

Random rubble stone masonry using approved local stones in foundations/pedestals and plinth at and at all depths below finished floor level in cement mortar 1:6 (1 cement :6 using crushed stone sand of grade conforming to BIS 2116) including simultaneous flush pointing with the same mortar, bond stones, curing, etc., using crushed stone sand of grade conforming to BIS 2116, complete as specified and directed.

BRICK MASONRY :

Brick work using quality flyash bricks of class designation 7.5 conforming to IS12894 using cement mortar 1:6 (1 cement :6 using crushed stone sand of grade conforming to BIS 2116 ) at all depths and heights below and above plinth level including pilasters, steel / tubular scaffolding, raking out joints, curing etc., complete as per specifications and as directed in super structure.

Half brick masonry using non modular fly ash bricks of class designation 10, conforming to IS :12894 in partition walls in cement mortar 1:4 (1 cement :4 using crushed stone sand of grade conforming to BIS 2116) all depths and heights below and above plinth level including scaffolding, raking out joints, curing, etc., complete including providing stiffeners of reinforced cement concrete 1:2:4, 115 mm x 75 mm size at every 900 mm height, necessary formwork, curing, etc., complete as per specifications and as directed but excluding reinforcement. Note:- Reinforcement will be paid under relevant item.

PLASTERING AND POINTING :

Cement plastering 15 mm thick for internal walls in cement mortar 1:4 (1 cement :4 sand) , and at all heights above plinth level over brick walls or concrete surfaces including making necessary grooves in between junctions of brick masonry and RCC and also other places wherever required over brick walls or concrete surface, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Providing and applying white cement based putty in two coats with average thickness not less than 1 mm, of Birla make or any other approved manufacturer, over the plastered wall surface (external/internal) to prepare the surface even and smooth complete.

PAINTING:

Wall & ceiling painting with premium acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.of Asian or equivalent in Pidilite, Johnson & Nicklson, Nerolac, berger brand, manufacture and shade over two coats of approved primer at all heights above plinth level including preparing the surfaces, scaffolding and cleaning, etc., complete and as directed.

Painting exterior walls on sand faced plaster with two coats of Alkali & fungal resistance, dirt resistance exterior paint with comprehensive warranty of 5 years of required shade of Makes Asian - Apex Advanced or equivalent in Pidilite, Johnson & Nicklson, Nerolac, berger, of exterior quality haying 100% acrylic, of approved shade including preparing surfaces, external putty of Birla or its approved equivalent wherever required applying one coat of approved primer as per manufacturers specification, applying and filling cracks or wherever required for external filler, curing, scaffolding, cleaning, etc., complete. Note :- Minimum Usage Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. or as per manufacturer's specification

FLOORING :

Providing and laying vitrified floor tiles of sizes(600mmX600mm) (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

MISCELLANEOUS ITEMS :

Providing and fixing 160 mm n.b.un-plasticised PVC rain water pipes with necessary PVC clamps and wooden gutties of approved make conforming to IS: 13592 type ‘A’with injection moulded fittings jointing with approved synthetic adhesive seal rings conforming to IS: 5382 embedding the slab junctions leakproof testing complete in line, level and plumb all as directed.

Supplying, lowering, laying, mentioned below the nominal bore, RCC SPUN PIPES (Class NP2) /NP 4 conforming to IS:458 with necessary collars, laid to correct grade and levels at and at all depths below plinth level including cutting to lengths, jointing with hemp yarn and cement mortar 1:1, caulking the joints and finishing, curing, etc., complete as specified and directed.

(b). 300mm NB NP-2

Supplying and fixing GI Chain link fencing of required height with 50mm diamond mesh of approved quality and make with 3.15mm(10 gauge) galvanized iron wires conforming to IS 2721 including unrolling, straightening, stretching, fixing tight to structural steel posts and struts erected in position by means of 6mm dia approved quality galvanized iron machine straightened rods at top and bottom horizontally throughout fence and vertically at every angle post, fixed with approved quality galvanized iron hooks, bolts, nuts and washers etc., complete as specified and directed(Line post, straining post , strut will be paid separately under relavent item)

DOORS, WINDOWS & ROLLING SHUTTERS ETC :

Supplying and fixing in position at all floors integrated powder coated aluminium(minimum thickness of polyester powder coating 50 micron), aluminium section [extruded] for aluminium Doors / windows (sliding/movable) /ventilators/ top hung/ fixed / grill/ adjustable louvered/ windows/ fixed partitions/ beading for fixing SS fly proof jali as per drawing of approved manufactures with extruded sections of Jindal / Indal / Aluminax or other approved eqivalent sections with size and weights as shown in the drawing, for frames and shutters [including wastages if any] conforming to relevant I.S specifications with all approved Bronze anodised aluminium fittings and accessories, locking arrangements, 2 / 3 rollers with ball bearings for sliding shutters of approved quality all as shown in the drawing, including providing and fixing aluminium channel beading / glazing clips fixed with necessary bronze anodised screws, grouting the gap with thermocole & GE sealant etc. all complete generally as per drawings, specifications etc., all as directed by Engineer in charge. but excluding the cost of glazing, which will be paid separately. NOTE: Approval of the Dept. for the complete design and shop drawing shall be obtained before commencement of the work.

Providing and fixing glazing with 5 mm thick plain float glass (weight notless than 12.50 kg/ sqm) of approved quality (Atul, Modiguard, Triveni, Hindustan Pilkington) including PVC /EPDM lining as per the drawing and as directed for doors & partitions.

Providing and fixing factory made single extruded WPC ( Wood polymer Composite ) solid door/window/ceosetory windows & other FRAMES / CHOWKHAT comprising of virgin PVC polymer of K value 58-60 ( Suspension Grade ), calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum , screw withdrawal strength of 2200N (Face ) & 1100 N ( Edge ) , Modulus of Elasticity 900 N/mm2 and resistance to spread of flame of Class A Category with property of being termite/borer proof, water / moisture proof and fire retardent and fixed in position with M.S hold fast / lugs / SS dash fastners of required dia and length complete as per direction of Engineer in Charge

Frame Size 65X100

Providing and fixing factory made single extruded wpc ( Wood polymer Composite ) solid decorative type flush door shutter 30 MM thick nd natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum frame density of 650kg/cum , screw withdrawal strength of 1800N (Face ) & 900 N ( Edge ) , Minimum compressive strength of 2200 N ( Face ) & 1100 N ( Edge ) , Modulus of Elasticity 900 N/mm2 and resistance to spread of flame of Class A Category with property of being termite/borer proof, water / moisture proof and fire retardent. WPC is to be laminated with pvc foil of minimum 14 microns , thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with neccessary full body threaded star headed counter sunk S.S Screws, including all hardware like aldrops, handles , tower bolts etc. complete as per direction of engineer in Charge.

35 MM Thick

Supplying and fixing to doors at and at all heights above plinth level approved best quality anodized extruded aluminium hanging floor door stopper (twin rubber stopper) with rubber cushion (anodic coating not less than grade AC 10 as per IS 1868))transparent or dyed to required colour and shade, with necessary screws etc., complete for twin rubber stopper.

Supplying and fixing to wooden doors etc. and at all heights above plinth level approved anodized extruded aluminium tower bolts conforming to relevant IS specifications (‘Classic’ or its approved equivalent) with approved cadmium plated brass screws of appropriate size etc., complete as directed.

a) using 250 mm long, 10 mm shoot.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers for aluminium doors and a pair of lever handles of approved quality with necessary screws with ISI marking classic/ J.S.E. (ECIE) make or any approved equivalent complete as directed by EIC

Supplying only approved anodized extruded aluminium heavy quality butt hinges with S.S. pin generally conforming to IS specifications CLASSIC, JYOTHI make or approved equivalent make) of size 125 x 63 x 4 mm with cadmium plated wood screws of appropriate size etc., complete as directed.

XIII. INTERNAL WATER SUPPLY:

Supplying, laying and fixing CPVC pipes confirming to ASTM D2846, SDR -13.5 at a working pressure of 320 PSI at 23 deg C, complete with all fittings and clamps, Fittings (Conforming to relevant IS/ASTM/BS code), in trenches, floors, walls including embedding if necessary, joining of pipes and fittings shall be done by solvent cement conforming to ASTM F-493, including bends, elbows, tees, reducers, sockets, unions and other specials, supplying and fixing with hooks in wooden plugs or embedding in walls and floors, cutting pipes to required lengths, making connections, cutting chases or holes in walls with machine & making good the same, testing, etc. all complete as per drawings, specifications and directions of Engineer-in-Charge. (CPVC pipes shall meet National Sanitation Foundation (NSF) requirement for drinking water system)

For the following Nominal Bore (NB) pipe: 15 mm

For the following Nominal Bore (NB) pipe: 20 mm

For the following Nominal Bore (NB) pipe: 25 mm

For the following Nominal Bore (NB) pipe: 40 mm

For the following Nominal Bore (NB) pipe: 50 mm

Providing and fixing in position heavy pattern screw down Gun metal ball valve with ball SS confirming to IS.778 with hand lever at top including testing for 10 kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc. as per specification.

a) 20mm nb

b) 25 mm n.b.

c) 40 mm n.b.

d) 50 mm n.b.

Providing hoisting and installing at required elevation minimum three layered moulded HDPE cylindrical vertical water storage tanks of various capacities of Sintex or Duracon make, with suitable SMC cover at top, coated with UV coating/layer including the cost of labour for making hole in the storage tank for inlet, outlet, scour and overflow and the required fittings/ gaskets, float valve including making necessary supporting system complete as directed

XIV. EXTERNAL/INTERNAL SEWERAGE:

Providing and fixing uPVC pipes of Ring Stiffness SN 8 & relevant fittings for underground drainage and sewer system of catgeory Type B and conforming to IS 16098 Part-1 , for all depths, correct grade, levels and alignment of following sizes and make M/s Ashirvad/Supreme or equivalent ,jointing with solvent weld or pushfit type for the external drainage system as per manufacturer specifications and encasing the pipe with 1:3:6 cement concrete. etc. and as specified and directed. Note :- The plain cement concrete will pe paid under relevant item

110 mm dia

160 mm dia

Providing laying or fixing in position under floors or against walls centrifugally CAST (SPUN) IRON SOCKET AND SPIGOT SOIL, WASTE, VENTILATION PIPES and fittings like bends, offsets, tees tappers, collars, connectors, plugs, shoes, etc. conforming to IS:3989, including cost of all fittings, jointing materials, joining with tarred spun (Jute) yarn and molten pig lead caulking the joints, including testing, painting with two coats of approved paint over a coat of primer etc. complete.

a) 75 mm n.b. pipes (with 1.8 kg of lead per joint)

b) 100 mm n.b. pipes (with 2.2 kg of lead per joint)

Providing and fixing in position best salt glazed STONE-WARE GULLY TRAP 150x150 mm square inlet and 100 mm n.b. outlet conforming to IS:651 including embedding the trap in 1:4:8 cement concrete.150mm x 150 mm C.I. grating at top, construction of brick masonry chamber 300 mm x 300 mm(internal) in 230 mm thick brick masonry in CM 1:6 over cement concrete of 150 mm thick bed of 1:4:8 embedding the trap, plastering with cement mortar 1:4, 20 mm thick on inside, outside and all exposed faces finished with a floating coat of neat cement, providing and fixing C.I. frame and cover weighing not less than 7 kgs, painting the grating, frame and cover with 2 coats of approved bitumastic paint etc. complete.

Construction of rectangular CHAMBERS of internal clear dimension of mentioned below ( internal clear) in 230 mm thick brick masonry in cement mortar 1:6 over a bed of 150 mm thick 1:4:8 cement concrete in foundation, plastering with cement mortar 1:4, 20 mm thick on inside, and all outside exposed surfaces finished with a floating coat of neat cement, 1:2:4 cement concrete for benching in slope 1 in 30 and channel finished with neat cement, brick corbelling at top if necessary to provide clear opening and providing and fixing CI cover with frame of light duty single seal pattern weight not less than 33 kgs embedded in cement concrete 1:2:4, providing and fixing C.I. steps weighing not less than 3 ½ kg each at 300 mm centre to centre if depth exceeds 800 mm, painting CI cover and frame and CI steps with two coats of bitumastic paint etc. complete-For depth of chamber not exceeding 900 mm. However minimum depth of chamber not less than 450mm

a) 450x600mm

b) 600x900mm

Extra over above item for depths beyond 900 mm of Rectangular chamber including providing and fixing C.I. steps weighing not less than 3 ½ kg each @ 300 mm C/C, staggered vertically and horizontally etc., as per specifications.

a) 450x600mm

b) 600x900mm

XV. MISCELLANEOUS SANITARY ITEMS :

Providing and fixing approved ORRISA PATTERN W.C. SUITE of M/s. Hindware or jaguar make comprising a) Orissa patterns W.C. best Indian make in light coloured glazed vitreous chinaware, 580 mmx400 mm with ‘P’ or ‘S’ trap. b) PVC low level flushing cistern of 10 lts. Capacity conforming to IS:7231 with all internal PVC fittings mounted on a pair of CI brackets of heavy quality with 32 mm nb PVC bend of required length complete. c) 32 mm nb PVC flush pipe of appropriate length with all fittings synthetic adhesive cement jointed concealed in wall. d) 15 mm n.b. heavy quality PVC inlet connection with CP brass unious at ends e) 15 mm n.b. heavy quality G.I. pipe and specials for overflow from cistern upto 150 mm above floor level concealed in wall and terminated with 15 mm n.b. CP brass mosquito proof jalli etc. complete f) 15 mm n.b. screw down heavy quality C.P. bras stopcock conforming to IS: 781. g) 15 mm n.b. heavy quality GI overflow pipe with specials from cistern

Providing and fixing wash basinsize 630X450mm of M/s. Hindware/jaguar or approved equivalent of with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, 15 mm n.b. screw down heavy quality C.P. bras stopcock conforming to IS: 781., 32 mm CP brass bottle trap, with extension pieceincluding painting of fittings and brackets, cutting and making good the walls wherever required complete as specified and directed

Providing and fixing as per IS 2556 flat back half stall urinal of size 580x380x350 mm of M/s. Hindware or Jaguar make supporting the pan on suitable heavy quality CI wall brackets, 32 mm n.b. heavy quality, approved make CP brass bottle trap with extension piece, fixing with CP brass spreader and suitable heavy quality CP brass waste coupling to urinal basin, CP brass grating, spring based flush valve for operation of water flushing etc., complete as specified and directed.

Providing and fixing SS liquid soap dish/ container ofHindware or Jaguar in with CP brass brackets, cap etc., fixed to wall with CP brass screws, screwed on to wooden rawl plugs etc., complete as directed for all wash basins.

Providing and fixing in position bevelled plain edged mirror 600 x 450mm made out of best Indian glass of 6 mm thick of approved manufacturer, mounted on plywood sheet/ plain AC sheet of 6 mm thick fixed in position with four number of CP brass screws with detachable CP brass caps, washers, rawl plugs, etc., complete for size given below.

Providing and fixing C.P. brass TOWEL RODS of approved equivalent of size 600 mm x 20 mm with a pair of C.P. brass brackets, wall flanges etc., of Hinware or jaguar make fixed to wall with C.P. brass screws, screwed on to rawl plugs etc., complete.

Providing and fixing cast iron "P" trap with 100 mm outlet, cadmium plated brass dome grating, necessary 1:2:4 cement concrete for embedding the trap, finishing interor portion of floor opening with cement plaster in CM 1:4 with floating coat of neat cement, etc., complete as directed for Urinals.

Providing and fixing CI NAHANI TRAP of self cleaning design of deep seal of over all depth of 150 mm and weight not less than 5.75 kgs with 75 mm outlet, having a minimum water seal of 50 mm with grating on top including necessary 1:2:4 cement concrete for embedding the trap, finishing interior portion of floor opening with cement plaster with float coat in CM 1:4 etc., complete with CP brass grating.

Providing and fixing approved type CP brass coat and hat hooks 2 Nos. (one unit) of approved pattern & shape fixed to wall/door shutter with suitable screws and plugs as required all as directed and specified.

WATERPROOFING :

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. NOTE :- 1)The treatment shall be tested by ponding water for a period of 10 days. If due to location of rain water pipes the average thickness of treatment exceeds 110 mm for easy flow of water the extra brickbat coba will be paid as extra item and the rate for the same to be got approved from the Department before execution 2) The waterproofing treatment is to be guaranteed for bone-dry condition for a period of 10 years in the prescribed proforma. 3) The measurement for payment shall be the entire area of terrace covered by the treatment measured between brick/concrete parapets without plaster and the area of vatas calculated by taking the length of vatas and the height above the finished level of the terrace.

Flower Pot

Designer Ceramic Flower Pot (small size minimum 6 inch height) as per EIC direction

Designer Ceramic Flower Pot (Medium size minimum 10 inch height) as per EIC direction.

Designer Ceramic Flower Pot (large size minimum 18 inch height) as per EIC direction.

Shade Net

Suplying and Shelling 50% Shade net of 1009 b virgin HDPE materials, with UVstabilizer @ 120 gram /Sqm. conforming to IS 16008.2016 (M/'s. JP, Mode ,shaliiner and kaveri ) above ground at required places of NFC as directed by EIC.

4 way fogger system

Supply and installation of 4 way fogger system including laying of PVC pipes, fittings, Tees, elboe etc with support as per direction of EIC.