Nathdwara Temple Board Tender

PROVIDING AND FIXING LEG PRESS including filling and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BELOW DIMENSIONS: - 1840mm (Length) x 360mm (Width) x 1560mm. (Height). SAFE AREA:- 2.8 x 1.4Mtr. Leg Press equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The center pipe is of 100mm NB made from “B” Class G.I. pipe. The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be disassembled from main frame. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The remaining outer frame is of 32NB made from “B” class G.I. pipe. The foundation used for fixing is structure and made from center pipe of G.I. of 80mm NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness. Seat & Back rest provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. The frame of footrests made up of 25 NB “B” class G.I. pipe. Closing Caps are made up of high quality Fiber reinforced Plastic material. To build structure bushes are used which are made from M.S. seamless pipe of 50mm O.D. and 5mm thickness.The pins used are made up of Ø25 mm SAE 8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed Brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly are of A24 mm. The powder coating done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING SURF BOARD including filting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS: - 910mm (Length) x 860mm (Width) x 1400mm.(Height). Safe Area:-1.39 x 1.27Mtr. Surf Board Equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The center pipe is of 100mm NB made from “B” class G.I. pipe. The sleeve pipe is of 125mm OD seamless pipe with thickness of 5mm and bolted to main frame with M10 SS bolts. The bottom support welded of M.S. plate of Ø 250 mm & 10mm thickness. The handle frame is of 25NB made from “B” class G.I. pipe. The paddle frame is of 50NB made from “B” class G.I. pipe is supported with 70 X 8mm bend M.S. flat and can be replaceable. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Bushes are used 70mm Outer Diameter with 5mm thickness is used. The footrests made from Aluminum casting material of size 320mmX270mmX5mm. For support to footrest 200mmX250mm with 3mm thickness M.S. Plate used. Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø35 mm SAE 8620 bright material. The bearing used are of “6007zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly is of A34. The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness. Includes as The cost/unit ie. Rate include basic item cost 6% Excise and 5% Vat, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING SKY WALKER including filting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height) SAFE AREA: - 2.7Mtr x 1.6Mtr. Sky Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm. The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle. The handle frame is of 25mm NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support. The footrests made from Aluminum casting material of size 130 X 310 X 5mm. Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø 25mm SAE8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball. The bearings used are “6205zz” are permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A24 type. The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness. Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING BENCH WITH DUMBLE including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE PRODUCT DIMENSIONS: - 2350mm (Length) x660 mm (Width) x600 mm (Height). SAFE WORKOUT AREA: - 3500mm (Length) x 2000 mm (Width). Bench with fixed dumbell equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The main frame having pipe 50 mm NB made up of “B” Class G.I. pipe. The middle connecting pipes are made up from 40mm x 20mm rectangular MS pipe. The handle frame is made up from 32NB “B” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 50mm O.D. and 6mm thickness as well as 25mm outer diameter solid bar is used. The structure having hole pass provision for foundation Weight plates are made from iron casting material which is permanently attached with 25mm MS solid bar. Shaft used of Diameter 25mm made up from SAE 8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand (FAG/SKF). The cerclips used for locking is made up of Ø25 mm. The powder coating is done by Pure Polyester powder with 60 to 70 micron thickness. Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING TRIPLE STANDING TWISTER including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS: - 1150mm (Length) x 1150mm (Width) x 1580mm. (Height). SAFE AREA: - Ø2.1Mtr. Triple Twister made from “B” Class Galvanized Iron (G.I.) Pipe of different NB NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The Center Pipe is of 100NB made from “B” Class G.I. Round Pipe. The bottom support welded is of M.S. round plate of Ø250 mm & 10mm thick. The standing frame is of 32NB made from “B” class G.I. pipe. The handle frame of triple twister is of 25 mm NB made from “B” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB “b” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness The standing plate is fitted on the frame made up of Ø 80 NB GI. pipe. M.S. Round Plate of size Ø300mm x 10mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. The Pins used are made up of Ø 35 mm SAE 8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING SHOULDER BUILDER including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS: - 900mm (Length) x 900mm (Width) x 1580mm (Height). Safe Area:- 1.9Mtr X 1.9Mtr Shoulder Builder Equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The Center Pipe is of 100mmNB made from “B” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness. Sleeve provided of M.S. seamless pipe of Outer diameter 125mm with thickness 5mm provided. The handle movement frame is of 25mm NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB “B” Class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm . thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø 25 mm of SAE8620 bright material. The bearing used is “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly is of A 24. The nylon bush is used for handle knob. The powder coating done with Pure Polyester powder of Ackzonoble or Berger Paints with 60 to70 micron thick. Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING AIR WALKER including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS :- 1060mm (Length) x 810mm (Width) x 1600mm. (Height). SAFE AREA: - 2.0 Meter x 1.8 Meter Air Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm. The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be easily disassembled from main frame. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link is supported with MS flat of size 60X8mm. The handle frame is of 25NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.Foundation cover Closing Cap is made from FRP Material with 0.7 mm thickness.Closing Caps are made up of high quality Fiber reinforced Plastic material.Pins used of Diameter 25mm are made up from SAE 8620 bright material. A24 circlips are used for assembly.The bearings used are “6205zz” permanent lubricated sealed bearing of repute brand. High tensile steel galvanized nuts & bolts are used for assembly. The powder coating is done by Pure Polyester powder of Ackzonoble or Berger Paints with 60 to 70 micron thickness.The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate.To build structure bushes are used which are made from M.S.seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used.Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING 4 IN 1 (SEATED PULLAR , LEG PRESS, SURF BOARD, SEATING TWISTER) including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE PRODUCT DIMENSIONS: - 2410mm (Length) x 1720mm (Width) x 2350mm (Height). SAFE WORKOUT AREA: - 4500mm (Length) x 4500mm (Width). Combination made from “B” Class G.I. pipe. The center MS pipe is of 100mmx100mm size. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The links are made up of 25mm NB “B” class G.I. pipe. The handle and seat frame of seated puller is made from 32mm NB “B” class G.I. pipe. For the assembly different bushes are used which is made from seamless pipe of 50mm OD and 5mm thickness & 50mm solid bar is used. Leg press center frame is of 32mm NB made from “B” class GI pipe. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The leg press footrest consists of 25 NB made from “B” class GI pipe. The pins used in are made up of 25 mm diameter hardened low carbon steel material. The Nut Bolts used for assembly are made from S.S. material. The bushes (stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mm diameter. Surfing frame is of 32NB made from “B” Class G.I. pipe. Surf board handle frame is of 25NB made from “B” Class G.I. pipe. 300mm diameter x 10mm thick plate can be used for rotating seat of seating twister with 50NB vertical G.I. pipe. Closing caps made from high quality FRP material which is of 2 mm thickness. The pins used are made up of 17mm diameter solid bar. The bearing used are of “6203, 6205” permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from M.S. pre-galvanized material. A17, A24, A34 circlips are used for assembly. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. It has Bolting provision for mounting on concrete slab. Polycarbonate sheet is used for roof with supporting frame which made from 25x25mm, 40x20mm MS pipes and 25mm NB “B” class G.I. pipe. MS 8mm thick round plate can be used for splitting roof structure from main frame. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with minimum 60 to 70 micron thickness.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

PROVIDING AND FIXING 3 IN 1 (LEG PRESS, AIR WALER,SURF BOARD) including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS: - 2300mm (Length) x 860mm (Width) x 1600mm.(Height). Safe Area:- 1.39 x 1.27Mtr. Air Walker cum leg press cum surf board Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame of 100NB made from “B” Class G.I. pipe. The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This Sleeve can be disassembled from main frame. The bottom support frame of M.S. 40mm x80mmx3mm thick C Channel. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The leg movement frame is of 32NB made from “B” Class G.I. pipe. The handle frame is of 25NB made from “B” Class G.I. pipe. Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm are made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.The bearings used are “6205zz” permanent lubricated sealed bearing of reputed brand.High tensile steel galvanized nuts & bolts are used for assembly.A24 mm cerclips are used for assembly.300mm diameter x 10mm thick plate used for rotating seat of seating twister with 50NB “B” class G.I. pipe.The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate.It has Bolting provision for mounting on concrete slab. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with minimum 60 to 70 micron thickness.Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance.

Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: a) 1:1½ :3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

b) 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size).

Providing and fixing rubber tile flooring 25mm thick made of SBR (Styrene- Butadiene Rubber) with interlocking arrangements and adhesive all complete colour and size as approved by Engineer-in-charge.