Nathdwara Temple Board Tender

Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size  FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade  and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694)   in  recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized  Modular box of 1.2 mm thick with earth terminal, 10 A modular  switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate,   screws, making connections, testing etc. as required.  For specification of copper  Conductor,  Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR On board

Long point  (up to 10 mtr..)

Supplying and fixing of power plug point with Modular accessories   as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of  ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification of  Wiring accessories refer Chapter  E - 07  related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

Providing & Fixing of following modular accessories as per PWD specification for electrical Works,  made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip  with IP-20 rating , including  all as per pre approved by Engineer in charge,making connections, testing etc. as required.  For additional technical parameters of product / work refer Annexure 'A' attached with this BSR RJ-11 telephone jack Double line

Blanking plate

Modular MCB 6 A to 32 A  DP

Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed  made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip  with IP-20 rating ,  including  all as per pre approved by Engineer in charge,making connections, testing etc. as required.  For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 5 step fan regulator 2 Module 360 dgree rotating

Providing & Fixing of modular type lockable feature socket duly  made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip  with IP-20 rating ,   including  all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 6/16 A  shuttered socket

Providing & Fixing of  following size mounting grid plates with cover plates made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 1/2 Module

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from  99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for  lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,  in existing  surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires.   For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 1 x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5sqmm

1 x 4.0 sq.mm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

4 x 6.0 sq.mm

2 x 6.0 sq. mm. + 1 x 2.5 sq. mm.

1 x 16.0 sq.mm

4 x 10.0 sq.mm

Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick  conforming to IS-8623-1 & 3 /  IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp.  insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set  of suitable rating and din bar,masking sheet,  making internal DB  terminations with copper lugs, Ferrules,  detachable gland plate, including making connections, testing etc. as required. OEM shall have submit  NABL / CPRI / ERDA accrediated   lab type test reports  & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Metal door (Three phase) IK-09 and IP-43  with Metal end box 6 Way

4 Way

Metal door (single phase) IK-09 and IP-43 with Metal end box 6 Way (6+2)

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and  site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of  class 3 as per IEC,  minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in  existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating  including making connections, testing etc. as required. OEM shall have submit  NABL / CPRI / ERDA accrediated   lab type test reports  & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Single pole MCB   (With B/C curve tripping Characteristics)  6 A to 32 A rating

 Four pole MCB (With B/C curve tripping Characteristics) 50/63 A rating

Double pole MCB(With B/C curve tripping Characteristics)  6 A to 32 A rating

Triple pole Mcb 6A to 32A Rating

S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with  ISI marked (IS:3419-1988) accessories as required  in  recess  including  cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 20 mm

25 mm

32 mm

40 mm

Making of hole in wall (brick/stone) of required and placing NP-2 RCC pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .  Up to 457 mm size   

P & F 1.2mm thick  M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,  12 mm dia rod fan hook with 100 mm  length extended on each side . All as per pre approved by Engineer in charge.  For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

Providing & Fixing of Heavy duty capacitor start, copper wound  Double ball bearing  900/1400 RPM single phase  Exhaust  fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 300 mm sweep(900/1400 RPM)

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium  housing with in built driver  , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD 10% , P. F.≥0.95, CRI 80 , life time of minimum  50000 Burning Hours with , 70% of intial Lumen maintaned till life ends  , CCT 3000°K / 4000°K  / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of  BIS standard and  trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.  All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 1170mm(+/-10%) LED batten with min. lumen output 2200 lm

Providing & Fixing of  BEE  Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic  blade ceiling  fan  Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 1200 mm Sweep BEE 1 Star rated (service value =4.0 to 4.5 )

Providing & Fixing of 450 mm Sweep  Oscillating type Wall mounting / Pedestal type  fans with Three speed, ON and  OFF position, Sintered Iron bush oil impregnated,  with metal front and back 120 or more  ribs guard; Three no. Aluminium  blades, minimum Air delivery 100 Cum. / Minute , Minimum Service Value 1.11 Cum./min/watt, noise level should be = 75 dB, power consumption = 120 watts, motor protection through thermal overload protection device, including fixing with anchor bolts, making connection testing etc. as required. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Wall mounting type with Adjustable Vertical Angle

Providing & Fixing of  of Double ball bearing, copper wounded capacitor start  single phase metallic  blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 300 mm sweep

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured  Aluminium  cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with  H4- Grade electrolytic  aluminium conductor confirming to IS 8130 of purity 99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831  in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including  testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 10.0 Sq. mm 4 core

50.0 Sq. mm 3.5 core

Supply  and  installation  of  high tensile low carbon steel rod molecularly bonded with 99.9 % Copper  thickness (250 microns) and  confirming to  UL 467, IS/IEC 62561-2  of following size and length and as per point mentioned (a), (b), [c), (d), (e) below :-   (a) Bore a hole of dia. 100 mm of required length, Place the rod in the centre of Hole  (b)  filled with anti corrosive  conductive  compounds with the permanent sealings at both the ends, CPRI/ ERDA  tested with RMS   capacity of minimum 30 KA for withstanding 1 second .To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab  for low  resistivity ( less than 0.12 Ohm - meter ) & high conductivity in nature with carbon as a major content  as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts  © Connect the rod with copper Strip/Conductor/Wire with suitable clamp made from tinned copper and SS 304 Bolt (d) Place Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height  250 to 300 mm. (d)  Testing of earth resistance for value of 5 ohms or less  as required & must record by engineer in charge during site visit and ensure to enter in measurment book. (e) Test certificates  for confirming above standards from OEM is mandatory. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .  17.2 mm thick and 3 Mtr. Long

Supply & Laying following size earth strip  in horizontal or vertical run in surface by means of Earth strip DMC Insulator  including riveting/ soldering/ welding, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required.All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    20mm x 3mm copper strip

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,  making connection with GI/Cu purity purity 95%  thimble etc. as required.  All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    8 SWG tinned copper Wire

P & F of Gravity Louver shutter of superior quality made out of frame of  18 swg M.S. sheet & Louvers made from 24 swg MS Sheet  with enamel paint including cost of nuts, bolts, etc as reqd.  All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Up to 380 mm size

Supply & Laying following size' B ' class ,  G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with accessories like bend, socket etc.  for laying earth conductor/ strip / cable in ground/ surface/ recess as required.  All as per pre approved by Engineer in charge.  (Earth Excavation will be Paid Extra)All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annex ure "A" attached with this BSR .    32mm dia

SITC of  3 /4  pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material  having following current rating, short circuit  breaking capacity  at 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front  face and centralised adjustable, trip free mechanisum, true contact position indicator,  line load interchangeability,  designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree,  pollution degree 3,   having positive isolation capability, push  (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage  690 V.  provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections  etc. as required.OEM shall have submit  NABL / CPRI / ERDA accrediated   lab type test certificate   before execution All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 4 pole MCCB With Thermal Magnetic release up to 100 Amp , 25 kA, adjustable O/L & adjustable S/C setting, 

160 Amp , 25 kA, adjustable O/L & adjustable S/C setting, 

125 Amp , 25 kA, adjustable O/L & adjustable S/C setting, 

Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulator  with standard short circuit withstand capacity    , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Electrolytic grade   (Cu-ETP) Tin Coated annealed copper bus bars IACS 100% grade

SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised  cubical panel as specifications and  Other parameters required  as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:- (a)Thickness of CRCA sheet shall  be 2.0 mm,  cable alley compartments having concealed hinged type doors with key type lock with / without  detachable extension type structure. Removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided (b)complete panel shall undergo a process of degreasing, Water rinsing, Activation, derusting,  pickling in acid bath, phosphatising & shall be subjected to nine tank process and then Powder coated with approved shade of minimum 70 microns on both side of panel.  The panel having PE foam/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire. [c)  Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar  (63 amp ) . control wiring will be carried out with 1.5 Sq.mm, Earth wire with 2.5 Sq.mm and CT with 2.5 sq.mm flexible copper wire only.  All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. ( Cost of Bus bar  / Flexible wire for Interconnection between Main busbar and Switchgear  is to be Paid Extra ) (d)Wiring between components within switchgear and Incoming / outgoing cable  shall be done through the terminal block only. Direct connection shall not be permitted. Each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. For tap-offs, adjacent terminals with shorting strips shall be used. 10% Spare terminal blocks shall be provided. Wire identification on marking strip shall correspond to the designation of the wiring diagrams. All wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. (e)All wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, Wiring between terminals of various devices shall be ‘point to point’ (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.(f)Floor mounted panel shall be mounted on Base frame of ISMC  channel size 100 x 50 x 5 mm  ( to be paid Extra )(g) Tests: The insulation resistance (with 1000 V Megger) and High voltage Power frequency test (by applying a voltage of 2.5KV for one minute) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. The insulation resistance shall not be less than three megaohm. CT Secondary current injection test shall also be carried out.(h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI Test certificates to be submitted)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .

Providing & Fixing of IS: 13875 & IEC :61326 confirming LED Digital type  (up to 500) V range Volt meter / Direct- Ammeter /  CT oertated ammeter/ Frequency meter / KWH meter / Multi Function Meter / Power analyzer of class 1 accuracy  as per IS : 1248 of size 96mm x 96 mm including making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required.  All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Single Phase Voltmeter

Single Phase Ammeter

Providing & Fixing of  flush head push button actuators IEC 60947  with integral circuit, IP 65 above panel &  IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min.  29 mm, contact material phospher bronze for Led, PCB contacts shall be of  brass (tin plated), impulse  dielectric tested for 2.5 KV,  including connection etc. as required.  All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .Luminous type  Red , Yellow, Green, Amber

Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum  material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover  and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy =125 lm/ wt   and potted driver  & has a unique BIS R number with  Input Voltage AC 120 to 270 V AC with High voltage Cutoff @=300 V AC and Auto resetting Safety , Power Factor 0.95 driver  Efficiency 85%  ,THD(I) 10%  Humidity 10% to 90% RH Working Temp -5C to 45C .  driver current 750mA. The luminaire  shall be BIS certified and Trade mark certified. Life Expectancy  Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI 70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs.  Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for  LED fixtures.    (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .LED Street Light fixture with Minimum lumen output 3700 lm 

LED Street Light fixture with Minimum lumen output 8700 lm

LED Street Light fixture with Minimum lumen output 12500 lm

Providing & Fixing of selector switch of 10 A for voltmeter  using high grade engineering material  to international standards with cam assembly  insulation of glass filled polyamide with high tracking index. For reliable and stable electrical and mechanical endurance double butt contacts with silver bi-metal on copper should provided . contact assembly is of operating temp range -25 degree C to 55 degree C, frequency upto 10 KHz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles/ hour and electrically 10,000 operations at 100% rated duty for 100 cycles/ hour including making connection etc.  as required . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Voltage Between Phases with OFF ( 4 Position )

Providing & Fixing of   CT linked selector switch of 10 A  for  Ampere meter (4 position )  using high grade engineering material  to international standards with cam assembly  insulation of glass filled polyamide with high tracking index. For reliable and stable electrical and mechanical endurance double butt contacts with silver bi-metal on copper should provided . contact assembly is of operating temp range -25 degree C to 55 degree C, frequency upto 10 KHz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles/ hour and electrically 10,000 operations at 100% rated duty for 100 cycles/ hour , including making connection etc.  as required .All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .

Providing & Fixing of ISO certified company made on load change over switch, front handle operated, four pole 415 V as per PWD specification  for electrical Works conforming to IS/lEC 60947-3 : 1999 including connections , testing etc. as required .in the following rating.  Appropriate type test certificate / OEM test report shall be submitted .  All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Open execution type  125 A

Providing & Fixing of   ding dong/musical chime bell as per PWD specification for electrical Works, including making connection testing etc. as required.All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .

Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type  Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate  from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .  6 kg

Providing & Fixing of Electrical  insulating rubber matts as per PWD specification for electrical Works, ISI marked confirming to IS: 15652 /  2006  with one side  anti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 3.3 KV,  class A 2 mm thick with proof voltage 10 KV AC (rms) and Break Down Voltage 30 KV AC (rms)

SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets  suitable for 100/150mm dia borewell.  The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,  & IS12615:2011  with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of  riser pipe G.I./  H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit  NABL / CPRI / ERDA accrediated  lab type test certificate   before execution. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .   100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. 2.0 HP, 1-Ø, (7- 95)Mtr, (55-22) LPM

Providing & Fixing of HDPE pipe Confirming to IS:4984:2021  for water supply suitable for submersible & jet pump with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    40 mm OD  6 kg / cm2

SITC of Contactor  OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and  made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF  push buttons,  ammeter, voltmeter, indicating lamps etc.  suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .     2.0 HP to 3.0 HP (DOL starter)

Providing & Fixing of  extra down rod of 15 mm dia . ERW (Electrical resistance welded ) of 1.6mm nominal thick medium duty steel  pipe including cutting, threading, drilling, fixing quarter pin etc as reqd.  All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .

Providing & Fixing of IP20, 2'x2' LED Surface/ Recessed  mounting Mid power SMD type LED Light fixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external surge protection BIS certified isolated driver having efficiency 85% , with Short & Open circuit protection  (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD 10 % , p.f.≥0.95,CRI 80 ,  life time of minimum  50000 Burning Hours with , 70% of intial Lumen maintaned till life ends  , CCT 3000°K / 4000°K  / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of  BIS standard and  trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on  housing.  Surface Moutning Minimum lumen output 3000 lm

Supplying and drawing PE Insulated & PVC Sheathed unarmoured telephone cable with 0.5 mm dia. Solid Annealed electrolytic grade bare Copper Conductor as per IS: 8130/84 &confirming to TEC specification GR / WIR/06-03 March 2002  in existing  surface or recessed conduit/casing capping. including ferruling on each pair for Identification etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 2 pair

10 pair

Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by  PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz.   in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack &  ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .   

Supply and Installation of unsheilded/360 degree sheilded Information outlets made of high impact plastic body with ABS, FR Grade halogen free material with provision for protection against dust in jack, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact termination on reliable copper tin plated Insulation displacement contact, with easy lock mechanism, It supports IEC 60603-7-4 and complied with ANSI/TIA/EIA 568 C.2 standard. jack should be RJ11,RJ12 & RJ45 compatible. Should support Ethernet 1.2 Gb/s ATM,Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP) Specifications in existing modular/MS Boxes along with necessory connections as required.All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    Cat 6, Un-sheilded Information Outlet

Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture ,  material should be  PC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions should be 86mm X 86mm as required complete in all respect.  All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    Single Aperture

Supply, Installation, Testing and Comissioning of Rack mounted 19" 1U, Cat6 24 Port loaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels  with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel. Etc. as required.All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    Modular Patch Panel Loaded with Cat -6 I/O

Supply , Installation, Testing and Comissioning of  Managed Layer-2 Intelligent 10/100 Ethernet Switch providing 24 x 10/100/1000 MBPS Giga Ethernet ports / with min 2 SFP Giga Ports (provision for Fiber Giga connectivity) with related LAN Base Software including making connections etc as required.All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .   

P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from  99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for  lower watt loss , oxygen free  for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,  existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 4.0 Sq.mm 3 core flat / Round

Supplying and making one end termination with Nickel plated heavy duty brass single compression gland (as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring,  Compression Nut,  heavy duty aluminium lugs (as per IS 8309 -1993)   duly crimped with crimping tool, PVC tape as per  IS 8337-1976  of  following size of  PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 3.5 x 50.0 sq.mm

P & F in position frame made out of M.S. angle (riveted or welded) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 40mm x 40mm x 5mm 

Supply & Installation of IP-20 & IK-08 , UL Listed  Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6 MM with 'U'Marking , with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19" angles with wall mounting provision on wall. Accessories like: 1 No of 19" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner  etc as required.All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    9 U Rack with Width 600 mm &  Depth 400 mm + 100 mm 

Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure  SMD Mid Power LED Downlight with power coated die-cast aluminum housing  with UV Stabilized non yellowish Diffuser with  BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency 85% . System Lumen efficacy of ≥ 110 lm / watt, THD 10 % , Pf.≥0.95, CRI 80,  life time of minimum  50000 Burning Hours with , 70% of intial Lumen maintaned till life ends  , CCT 3000°K / 4000°K/  5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of  BIS standard and  trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on  housing.   Surface Mounting (with extruded alumn. Housing ) Minimum  lumen output 1950 lm

Minimum lumen output 1300 lm

Providing & Fixing of BIS approved  Current Transformer  as per PWD specification for electrical Works ,ISI marked as per  IS 2705-1992/ conforming to IEC 60044-1, with secondary terminal  of CT shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required  Current transformer Ring Type Tape Wound/Resin Cast Wound   as per IS 16227 with, Accuracy Cl, CT ratio and burden as specified. ISF=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connection etc. as required . All as per pre approved by Engineer in charge.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . C T Class 1, Ratio upto 150/5, Burden 5 VA

C T Class 1, Ratio 200/5 to 300/5, Burden 10 VA

Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    16mm (suitable above 50mm & up to 75mm OD pipe)

Supply , Installation, Testing and Comissioning of IS:1475 marked self contained drinking water cooler with  hermetically  sealed compressor,non CFC refrigerent suitable for operation on 230V/1pH/50Hz AC supply,Full stainless steel (SS304)body (0.8 mm thick)  and tank (0.5 mm thick) , stainless steel water tray,minimum two nos  Brass Chrome plated faucets and suitable drainage system complete in all respect with required  height MS fabricated and Painted Angle iron frame  ( Cost of frame to be paid Extra )complete in all respect of the following capacity.  All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    cooling capacity 150 Ltr./Hr. and storage capacity 150 Ltrs

P & F Krone module with base frame  in the recess / surface made out of 1.2 mm thick  sheet steel box, front openable, having locking arrangements duly powder painted,including dressing, ferruling  and  punching  of telephone cable with krone tool etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 10 Pairs

50 Pairs

Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A /Class E/Ea patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors with strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568C.2, ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802.3an minimum requirement for 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, should support IEEE 802.3af / IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts for long durability, Should support Ethernet 10GBASE-T, 1.2 Gb/s ATM, Token ring 4/16, Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP).All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR .    Cat 6, U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch Cord 1 Mtr

2 Mtr 

Providing & Fixing of self healing IP20 MPP type shunt capacitor (banks) conforming to IS:13340-41 /  IEC :831-1&2 OR IEC : 60831-1& 2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( PSD ) and shall have dissipation factor less than 0.0025 at 50 Hz, Operating loss less than 0.30 Watt per KVAR. Min over current capacity 1.8 times rated current & peak inrush current min. 300 times of rated current, llife expectancy greater than 100000hrs  (temp class - 25 D)  in 440 V/480 V Capacitor and for 525 V should life expectancy minimum 1,65,000 hrs (temp class - 25 D)  including making connections, testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Heavy duty  Three phase 480 V, 50 Hz  cylindrical type capacitor (Bank)

Providing & Fixing of IP54 microprocessor based 3 CT’s for all 3 phase  sensing compensation  power factor correction relay Size 139mm x 139 mm, Operating Voltage 415/440 V  , IEC / EN 61000-6-(2&4)  having 3 CT sensing, sensitivity up to 50 milli amp secondary current , self analysing auto c/k setting according to targeted power factor setting, the relay shall have  digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with RS 485,  indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi parameter like KW, KVA, KVAR, RMS Value, step switching time 2 sec to 1800 sec. Lead & Lag parameters, metering facility and  3 no. Class- 0.5 Cast Resin  CT ( refer CT specs in this chapter )for sensing the relay including making coonection with 1.5 Sq.mm copper wire etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 6 to 8 stage 

Providing & Fixing of  440 Volt 3 pole capacitor  (AC 6 B ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current as per PWD specification for electrical Works,  IS/IEC 60947-4-1 : 2000, insulation voltage 1000V, impulse withstand voltage 8 KV,Din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank.  All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . up to 6 KVAR

10 KVAR

Providing & Fixing of    Cam operated rotary (Auto/manual) switches on existing panel with 2 way and off position using high grade engineering material  to international standards with cam assembly  insulation of glass filled polyamide with high tracking index. For reliable and stable electrical and mechanical endurance double butt contacts with silver bi-metal on copper should provided . contact assembly is of operating temp range -25 degree C to 55 degree C, frequency upto 10 KHz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles/ hour and electrically 10,000 operations at 100% rated duty for 100 cycles/ hour including making connection etc.  as required . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . 10 Amp

32Amp

Supply and Fixing of Pole OEM fabricated hot dipped galvanised M.S. Overhang (48.3 X 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. All as per pre approved by Engineer in charge.  For additional technical parameters of products/ work  , refer   Annexure "A" attached with this BSR . Single arm overhang