Mohanlal Sukhadia University Tender

Providing and applying melamine polish (matt finish) for ceiling and flooring of required finish to the wood work using spray machine including knotting and preparing the even surface by scribing, applying primer finish including cost of scaffolding etc. complete.Spec: As directed by engineer in charge

Providing and fixing frame work of T grid sections 15 mm widehaving grove, white colour having load capacity not less than 14 kg/ sq m & warranty of minimum 10 years suspended from the slab using proper fasteners & straightened hanger wire of dia –2.5 mm and a tensile strength of 344-413 MPa, along withAdjustable hook clips of 0.8mm thick, galvanized spring steel for2.68 mm with a minimum pull strength of 110 kg. The adjustable clip also consists of a 3.5 mm aquiline wire to be used with the main runner, this suspension system should be as specified by the original manufacturer at maximum 1200 mm c to c . etc, complete. (Frame as per manufacturer specification)Spec. No.: As directed by Engineer in charge.

Providing and fixing false ceiling of 15 mm thick Armstrong optra or equvalant ceiling tiles in T grid using manufacturer specified accessories including scaffolding and architectural work like moulding, cornices, coves, domes, cups as per detailed drawings etc. complete. (excluding frame work, runners and steel suspenders)Spec. No.: As directed by Engineer in charge.

Providing & Fixing in position Acoustical Paneling of Armstrong or equivalent made fromfactory finished Fabric Wrapped Compressed glass wool 25 mm thick panels of size 1200mm x 600mm & fire resistant, having NRC 0.85 fixed on Al frame using adhesive or as per manufacturer's details, including cost of required Cut-Outs & Scaffolding as per detailed Architectural - Acoustical Design & Drawings etc. Complete in all respect as directed by engineer in charge (Excluding cost of frame )

Providing & fixing Wooden veener false ceiling comprising of the following: 4mm thick veneer finish ( Duro group B) over 12mm thick commercial ply (Century/ Green/ Kitply/ Garnet) with hard wood (Beeachwood) frame of required section fixed to wall & ceiling with necessary nails & screws as required and as per drawing. Veneer Make: Duro , Commercial Ply Make: Century/ Green/ Kitply/ Garnet veneer finish wood beading all around as required. Including all necessary nails, glues, teak wood lipping, , wood preservative paint, fire retardant paint, brushed steel hinges for trap door shutter including making opening for lights, AC grills etc. complete as per design and drawing. (Contractor to include the cost of members & all required accessories for installation compelet in his quoted rate)

Providing & Fixing in position Acoustical Paneling of Armstrong or equivalent made fromlaminated HDF with groves from front side & perforation from rear side of size 128mm x 2440mm x 16mm, Fire rating class 1 as per part 7 of BS 476 & NRC 0.50, fixed as per manufacturer's details using Al keels, on AL frame in front of 800 gsm synthetic wool 50 mm thick with chicken mesh jali of 24 gauge on wall side including cost of required Cut-Outs & Scaffolding as per detailed Architectural - Acoustical Design & Drawings etc. Complete in all respect as directed by engineer in charge (Excluding cost of Al- frame)

Supply installation testing and commissioning fix chair, fabricate theater seating as per following specification (i)SEAT REST ASSEMBLY:- The seat rest assembly is 1.2+0.1cm thk. Flat plywood measured as per QA method described in OCP-QLTA-P14-18 eith mulded polyurethane foam & upholstered with 3 layered foam laminated fabric. The Seat profile is developed to help the users to get necessary Comfort SEAT SIZE: 45.0 cm (W) x 44.5 cm (D) x 12.0 cm (T) @ fRONT EDGE AND 8.0 cm @ Rear edge. TIPUP (ii)BACKREST ASSEMBLY:-The backrest assembly is made up of a M.S tubular frame in-situ moulded with polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort at upright . The back frame is having nylon reinforced elastic bands to retain the profile and give a better cushioning feel. "BACKSIZE:46.5cm(W) X 62.5cm (H) x 9.0cm (T) Avg. (iii)HIGH RESILIENCE(HR) POLYURETHANE FOAM:The HR polyurethane foam for Seat and Back is moulded with Density=48+/-2kgs/cu.m and hardness load 16+2 kgf as per IS:7888 for 25% compression. (iv)ARMREST:The armrest is made up of integral Polyurethane Foam with 65+/-10 Shore'A' Hardness and reinforced with M.S. insert. The armrest is avalible in two options-with and without cup holder. (v) SIDE PANEL/AISLE PANEL:-The chair rests on the ground on two side panels frames made of 0.25+0.020thk CR steel,Each side Panel is clad with two fabric upholstered particle board of 0.9cm thk. The side panel frame is grouted to the floor using 2 Nos. anchors for each panel throught the 05+0.05cm.thk HR steel base plate. (vi) PWODER COATING:All steel componets are epoxy polyester powder coated(DFT40-60microns (vii)UPHOLSTERY FABRIC:The 3 layered foam laminated fabric of required and approvd by engineer incharge. Approved Make :- Pen workers/ Geekan/ Godrej or equivalent

Providing and fixing 12mm thick solid acrylic surface (Solid acrylicsurface with CNC cutting design) of approved shade with pattern as perinstructions of Architect / Engineer-in-charge.

Providing and fixing 8-10 mm Designer MDF decorative panels (Glowood/Alko bond or equivalent) board of approved design on existing ply and finishing itwith DUCO paint of approved colour, complete with 4 MM teak beading onall exposed edges finished with polish to the complete satisfaction of the Architect & Engineer in charge.

Sound Proof Door: Providing and fixing 85mm thick acoustical door for the theatre shutter finished with laminate on both side. Door shall be made in sal wood frame in 75X35 frames shall have both side and glass wood frame of 50mm thick 24 kg/pm2 shall be kept between wooden frame. Door shutter have rebated having thin flat lining for making almost air light door. Fixing 3mm thick. Tec sound or equivalent insulation layer in between two frame. Door shutter to have following SS fitting and fixture. Heavy duties washer hires 200X50X6mm 4 Nos. 12mm dia 300mm long top and bottom tower bolt 65mm dead lock 30mm dia handle 600mm long as approved by E.I. 4 Nos., door size frame 150X75mm thick and installation including door frame complte as per direction to engineer incharges.

Providing and fixing wall acoustical paneling Fixing polyester fiber acoustic wall paneling with the specification of 9MM thick having density of 237 kg/m3 with NRC value of 0.80 surface matt finish which is fixed with solution SR505 as required. The panel should have euro class B ASTM E84-13 fire rating. The color shade of Panel as approved by Architect. Panelling should be fixed over the GI framing as required for the panel sizes. Rate is Including all accessories, material & labor complete as directed by Engineer.

Providing and fixing of Effective Optimized System Roller blindsincluding roller tube, control chain, control set with left hand,control set with right hand, bracket cover, chain connector, O-C BottomRail String for conversion, bottom end plug, open bottom rail, tubebearing plug etc with 50% light transfer all complete as per directions& instructions of Engineer-in-charge at site.(The sample should be gotapproved by Engineer-in-charge in advance before placing theorder).

Supply of Celling Suspended Air Cooled ductable type A.C unit with Inverter Based Scroll compressor for additional power savings & to cater Diverse load application. The unit shall consist of Indoor unit suitable to mount above the false ceiling and shall consist of Blower, Motor, Cooling coil, Electronic Expansion valve, shut off Valves , FIlter dryer etc. complete in all respects.The outdoor unit shall consist of Inverter Driven compressor with VFD drive along with Condensor Fan, Condensor coil , Motor complete in all respects.The Unit shall be operated with Micro processor based control panel & shall have Touch PAnel type corded remote control 11.0 TR( With 1 Inverter Compressor). Approved Make :- Hitachi/ Daikin or equivalent

...................do...............8.5 TR ( With 1 Inverter Compressor). Approved Make :- Hitachi/ Daikin or equivalent

Installation and Commssioning of DUCTED A.C. unit , Includes pressure testing , vaccumising with First Charge of R410 & Oil etc. 11.0 TR

..............do.............8.5 TR

S. I. T. C of Insulated Copper refrigerant piping for A.C for below mentioned units 11.0 TR

..............do.............8.5 TR

S. I. T. C of Electrical control Flexible cabling between indoor & Outdoor

S. I. T. C of Insulated Drain water piping of PVC with 6mm thick closed cell nitrile rubber sleeves.

SITC of MS stands for ODU units made up of 40x40x5mm Angle Iron duly painted with 2 coats of synthetic enamel paint

S.I.T.C of G.I Rectangular Ducting complete in all respects.24 G

........do...........22G

S. I. T. C of Thermal Insulation of G.I Ducts with 13mm thick Closed cell nitrile rubber

S. I. T. C of Accoustic insulation of G.I ducts with 10mm open cell nitrile rubber

SITC of Aluminioum extruded section grills duly powder coated of approved shade.

SITC of Aluminium collar dampers

SITC of canvass connections between Indoor Unit & Ducts. NOTE: 1. Quantities of item may increase or decrease as per site requirement. 2. Any item may be deleted if not required. 3. All item rates should be including of all taxes. 4. The lowest bidder calculated by treating all item as complete job work.