Military Engineer Services Tender
... More
The MES has issued a formal invitation for competitive bids for the Military Engineer Services project, for Provn Of Drone Protection Nets For Blast Pens At Af Stn Nal Under Ge (af) Nal in Bikaner, Rajasthan, with an estimated contract value of Rs. 73,00,000. The bid opening date for this tender is 30-10-2026 and the last date for bid submission is 27-11-2026. Interested bidders for Military Engineer Services tender can download the important documents here to check the scope of work, eligibility criteria and technical requirements.
Costs
EMD
₹ 1,34,500Document Cost
₹ 1,000Tender Fee
Refer Documents
Description
Provn Of Drone Protection Nets For Blast Pens At Af Stn Nal Under Ge (af) Nal
Contact
Tender Id
2026_MES_796626_1Tender No
C-81701/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Returing filling in including spreading, levelling, watering and well ramming in layers n exc 25cm thick as in soft/ loose soil complete all as specified and directed.
38.48
-
-
... More
Removing excavated material exc 1.50 km but n exc. 5 km and deposting where directed
53.68
-
-
... More
Form work of rough finished flat surface to side of concrete foundations, footing, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams, and similar work vertical or to batter.
179.2
-
-
... More
Form work of fair finshed flat surface to sides of pillars, posts, struts, piers, columns and stanchions.
46.08
-
-
... More
M&L for RCC M-25 design mix for foundation including rafts, footings, foundation beams, plint beam, base of columns, etc basement slabs, under-reamed piles and mass concrete complete all as specified and directed.
35.6
-
-
... More
M&L for RCC M-25 design mix for columns, pillers, piers, posts and struts.
4.64
-
-
... More
M & L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips, including as in lacing to complete all as specified and directed.
12302.31
-
-
... More
M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.
422.56
-
-
... More
S & F for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, confirming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.
19392.96
-
-
... More
M & L for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, concrete surfaces, water trough and like including rounded or charmfered on edgesconfirming to Fe 410-W (Gde-E-250) quality-A, complete all as specified and directed.
2293.52
-
-
... More
Material and labour for mild steel screw bolts, purpose made, with hexagonal or square heads at one end and screwed the other, or screwed both ends, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long, diameter of neck exc 20mm n exc 25mm, complete all as specified and directed.
817.92
-
-
... More
S & F for bands, straps, supports or stays for columns, including welding or bolts, hooks (stay), hook and clamps; hold fasts; wall tie; hooks for conforming to Fe-290 Gde-165, complete all as specified and directed.
1085.18
-
-
... More
M & L for preparation of new steel & iron surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete as specified and directed.
909.98
-
-
... More
S & F for nylon net woven out of nylon thread (virgin quality) of 3mm dia and size of mesh 25mm control UV stabilized multi filament including steel rings with tying rope attached, complete all as specified and directed.
5222.4
-
-
... More
S & F cast iron work grade FG 150, machined, in pulleys and similar articles ,complete all as specified and directed.
711.68
-
-
... More
S & F for 12.50mm dia nylon rope, complete all as specified and directed.
2982.4
-
-
... More
S & F for 4.0mm dia galvanised mild steel plain wire, complete all as specified and directed.
65.28
-
-
... More
S & F for 5.0mm dia galvanised steel chain link hemming/tension wire, complete all as specified and directed.
1370.88
-
-

