Maharana Pratap University Of Agriculture And Technology Tender

Provding & installing metal in Tile 600 x 600 mm perforated false ceiling system exposed on T" grid system. Panel shall be fabricated from 0.56 mm thick (TCT) Aluminium and powder coated on external surface shall have flange on all four sides to reifo n t e exposed grid system to given 600x6OO mm centre to centre of T . Panels will be plain for flush look with T ; Tiles shall haw 2.5mm dia at 5mm centre to centre in square pattern. rhe T shall be hot dipped GS Tee section 3600 mrn long main Tee 24mm wide, Cross Tee 1200 mm & Cross Tee 600mm to form grid of 600x6OOmm. rhe installation to be carried out with main runners spaced at 1200mm centres securely fixed to the slab / Truss by means of Roll Plug and 4mm dia G I rod at 1200 mm maximum and not more than 150mm from sliced joint. The last runner should not be greater than 600mm from the adjacent wall, 1200mm Cross Tee & 600 mm Cross Tees to be interlocked between two main Tees to form grid 600 x 600mm. Panels are then placed indi\Adually on the 600 x 600 mm exposed grid frame work created by Tee. GS edge profile shall be fixed on the perimeter of walls and columns. The carrier shall be suspended from slab by 4mm dial galvanized rod with special height adjustment power coated clips made out of spring steel at maximum 1.2 to 1.5 mtr. Centre to Centre. The 4mm dia galvanized rod shall be fixed to slab by forming one end "j" shape with roll inserts. The edge profile formed out of G.I. sheet of the size 18mm x 20mm shall be fixed on the perimeter of the walls. inclusive of Pro%Ading and fixing of Non woven Cloth, 5mm thick class wool packed in poly bag,25mm thick class wool packed inpoly Bags Designer false ceiling

P & F 1st qualityVitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete.Size 900 mm x 900 mm

Providing and fixing anodized aluminium work (Anodizing to be got done from approved Anodizer) for doors, windows ventilators and partition with extruded built up standard tubular and other sections of approved make conforming to IS : 733 and IS 1285 anodised transparent and dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15), fixed with rowel plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gap at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth rust free straight, mitred and jointed mechaincally wherever required including cleat angle Aluminium snap beading for glazing /panelling, C.P. brass/ stainless steel screws, AI. Tower bolt & AI handle & Al. Aldrop etc. all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separtely)

(a) For fixed portions

(b) For shutters of sliding windows and making provision for fixing of fittings wherever required (lockes shall be paid for separately)

(c) For shutters of openable doors, windows & ventilators including providing & fixing hinges / rollers etc. and making provisiion for fixing of fittings wherver required (lockes shall be paid for separately).

Polyester powder coating and electro coloring in various colour and shade approved by engineer in charge (For item No 16.1.1.)

(a) Section 101.60 x 44.45 mm

(b) Section 63.00 x 38.00 mm

Providing and fixing glazing in aluminium door, window, ventilator shutter and partition etc with PVC/Neoprene gasket etc complete as per the Architectural drawings and the direction of Engineer in charge ( cost of aluminium snap beading shall be paid in basic item)With glass panes of 5.0 mm thickness (weight not less then 13.75 kg/sqm) as per IS:2835

Providing and fixing expanded grill made of anodised aluminium as per design and drawing having members section of 7.5 mm x 6.0 mm and opening of size 102 mm x 99 mm to aluminum window/vent with required screws. Y and H aluminum sec ( as per drawing) at the ends and middle joints respectively complete in all respect as per direction of Engineer-in-charge. polymer power coated aluminium section

S&F fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3 mm with suitable screws at not exceeding 150mm distance at all height with all lead and lift with scaffolding

Providing and fixing 12 mm thick prelaminated three layer medium density (Fxterior grade) particle board grade I type IInd conforming to IS: 12823 bonded formaldehyde synthetic resin of approved brand and manufacture in paneling fixed in aluminium doors windows shutters and partitions frame with C.P. Brass /stainless-steel screws etc. complete as per Architectural drawing and direction of Engineer in charge. Pre laminated particle board with decorative lamination on both side

Providing and fixing wall panelling using soft wood frame of size 50x25mm @ 600mm c/c in both directions duly treated with antitermite treatment making grooves painting of grooves specification and drawing using . 12mm thick Acoustical board with 25mm thick glass wool.

Providing and fixing Granite stone slab thickness 16 - 18 mm mirror polished and machine cut in walls, pillars, steps, shelves, counter, floors etc. laid on 12 mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1 White cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of.South (Red/Choclate Colour), Above 3601 cm2 Slabs

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work including prepration of base with primer putty lippy complete in all respect.

Applying white cement based putty over cement plaster surface for making even surface

Providing and fixing in position collapsible steel shutters with vertical M.S., Channels 20x10x2mm and bracket with flat iron diagonals 20x5mm, size with top and bottom rail of T-iron 40x40x6mm . with top flat of 50 x 10 mm and bottom flat of 40 x 6 with 40mm dia steel pulleys/ ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer ( To be measured and paid as per outer dimension).With 75 mm opening when closed.

Wiring of light point/ fan point/ exhaust fan point/ call bell point As per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B., Bends etc.), round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 . For additional.

(a) S.P. (up to 3 mtr.)

(b) M.P. (up to 6 mtr.)

(c ) L.P. (up to 10 mtr.)

Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modular switch, 3/ 5 pin 6 A modular socket, Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05

(a) On board

S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .

(a) 25 mm

(b) 20 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( 10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4,, in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

(a) 2 x 1.5 sq.mm

(b) 2 x 2.5 sq. mm. + 1x1.5sqmm

(c) 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .

Providing & Fixing of 240/415 V isolator as per PWD specification for electrical Works with ISI marked IS:13947- III/conforming to IEC 60947-3, suitable for AC22A utilization catagory, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation, two position din rail mounting, minimum phase termination capacity of 35sq.mm., label holding facility, IP 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .

(a) 80 A/ 100 A rating

Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI/ ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

(a) 4 Way ( 12 O/G + 8 I/C )

Providing & Fixing of non modular socket size flush type 120 watt rotary minimum 5 step fan regulator as per PWD specification for electrical Works, ISI marked (IS:11037) made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .

Plate Earthing as per PWD specification for electrical Works As per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .8 SWG G.I. ( Hot Dipped ) Wire

Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ), cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR . 1200 mm Sweep BEE 2 Star rated (service value =4.5 to 5 )

Providing & Fixing of following modular accessories as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating, minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 2 pin Telephone socket

Providing & Fixing of following size hot dip galvanized M.S. box of 18 SWG as per PWD specification for electrical Works, with earthing terminal in recess/ surface suitable for modular accessories as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR . 1-2 Module

Providing & Fixing of following size polycarbonate modular boxes as per PWD specification for electrical Works, as per IS 14772-2000 in recess/ surface suitable for modular accessories as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 1-2-3 Module

Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency 85%, with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD 10 % , p.f.≥0.95,CRI 80 , life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. Recessed Mounting 36W LED light fixture 2'x2' with acrylic / prismatic front cover.

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver, Power Consumption of 18W/20W,system lumen efficacy ≥ 120 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD 10% ,p.f.≥0.95, CRI 80 , life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin), maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. 4' LED Tube shape fixture 18/20 W (Extruded Al Base)

Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 18 SWG with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) [ as per detailed in respective item in BSR], making connection, testing, etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR .

Providing & Fixing of of M.S. J- hook of standard design made out of 16 mm dia. M.S. round bar and fixed with cement concrete mortar with required support as required.