Maharana Pratap University Of Agriculture And Technology Tender

Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish:25mm thick

Cement mortar 1:4 ( 1 cement : 4 coarse sand )Add extra over item no 5.8 for half brick masonry in superstructure up to third storey including cost of nominal hoopreinforcement (2 Nos. 6 mm dia M.S. bar at every forth course)

M10 grade Nominal Mix (with graded stone aggregate 40mm nominal size)

Providing and fixing factory made polyvinyl chloride (PVC) Door frame manufactured of the size 50x47 mm with a wall thickness of 5 mm made out of extruded 5mm PVC foam sheet mitre cut at two corners and jointing with 2 nos of 150 mm long brackets of 15x15mm M.S. Square tube. The two vertical door profiles are to be reinforced with 19x19mm M.S. square tube of 19 gauge. EPDM rubber gasket weather seal to be providing through out the frame shall be fixed to the wall using 65/100 mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 4 nos of screws to be provided for each vertical member and minimum 2 nos for horizontal members etc. complete as per manufacture specification and directon of engineer in charge.

Providing and fixing 30mm thick FACTORY MADE SOLID BOTH SIDE PRELAM PANEL PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for stiles top & bottom rails M.S. frame shall have a coat of sheet primers of approved make and manufacture, M.S. frame covered with 5mm thick heat moulded 'Rajshri' prelim PVC 'C' channel of size 30mm thickness, 70mm widthout of which 50mm shall, be flat and 20mm shall be tapered in 45" angle on either side forming stiles and 5mm thick 95mm wide Rajshri Prelam PVC sheet out of 75mm shall be flat and 20mm shall be topered in 450 on the inner side to from top and bottom rail and 115mm wide Rajshri Prelam PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail Top bottom and lock rails shall be provided either side of the panel 10mm (5mm x 2) thick 20mm wide cross PVC sheet shall be provided. as gap insert for top rail and bottom rail. Panelling of 5mm thick both prelam PVC sheet to be fittted in the M.S. frame welded/sealed

Providing and fixing glazing in aluminium door, window, ventilator shutter and partition etc with PVC/Neoprene gasket etc complete as per the Architectural drawings and the direction of Engineer in charge ( cost of aluminium snap beading shall be paid in basic item)With tinted glass panes of 5.0 mm thickness (weight not less 13.75 kg/sqm)

Providing and fixing Ist quality standard White/ ivory,grey, fuma red brown, light green, light blue and other light shades Glazed Tiles of (confirming to IS : 13753 & IS 13622) of size 300 mm x 200 mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (Fxcluding the cost of cement plaster on walls & pillars ).

Providing and fixing Ist quality MAT finished ceremic tiles size 300 x 300 mm confirming to IS: 13755 & IS: 15622 colour such as white, grey, Ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortar bed 1:4).

Applying Birla /JK white cement based putty over cement plaster surface for making even surface

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work including prepration of base with primer putty lippy complete in all respect.

Painting with enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work

P & F WVC wash basin (Ist quality, I.S.: 2556 Mark) of approved make with C.I. brackets duly painted 1 No 15 mm C.P. pillar cock (I.S. : 8934 Mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall. Size 580 x 450 mm

P & F Indian type white glazed vitreous china Ist quality W.C.orissa pan (I.S: 2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor. Size 580 x 440 mm

P & F European type white glazed vitreous china Ist quality double syphonic W.C. (I.S: 2556 Mark) with P or S trap including cutting and making good the wall and floor.

P&F Ist quality WVC Urinal (IS :2556 mark) with 25 mm dia G.I.waste pipe, dome waste couplings, concealed iron brackets or screw etc. complete. Flat back (large) or half stall size 610x400x80mm

Providing and fixing Granite stone slab thickness 16 - 18 mm mirror polished and machine cut in walls, pillars, steps, shelves, counter, floors etc. laid on 12 mm (Av.) thick base of cement mortar 1:3(1 cement : 3 coarse sand) jointing with white cement mortar 1:2 ( 1 White cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of. Jhansi (Red/Choclate Colour) Above 3601 cm2 Slabs

P & F Looking Mirrors with P.V.C. frame of approved (Atul Modi Guard Saint Gobin or equivalent) Size 500 x 400 mm

C.P. brass towel rail elbow type with concealed screws size 450 mm (Heavy duty). C.P. brass towel rail with brackets 600 x 20 mm

P & F Grating of approved quality /make. Stainless steel sheet size 125 mm dia

Providing and fixing C.P. flange for 15 mm dia taps

P & F GI pipes ( Internal works ) with GI fittings excluding Union (IS:1239 mark) and MS clamps, including cutting and making good the wall and floors.(a)15mm dia Nominal Bore.''B' Class

P & F GI pipes ( Internal works ) with GI fittings excluding Union (IS:1239 mark) and MS clamps, including cutting and making good the wall and floors.(b)25mm dia Nominal Bore.''B' Class

Making connection of GI distribution branch with GI main including all fitting.Upto 25mm dia

P & F 15 mm. Dia Connection Pipe of approved quality/ make :PVC pipe with C.P. Brass nuts upto length, 600mm

P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make :CP brass push type 25mm nominal bore.

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make:(a)Gun-metal 15mm nominal bore.

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make:(b)Gun-metal 25mm nominal bore.

Providing and fixing Superior quality (Jaquar Contiental) CP Brass Fittings complete as per direction of Engineer in Charge.(a)Swan neck pillar cock 15 mm nominal size

..do..(b)Bib Cock with long thread 15 mm nominal size

..do..(c)Long body Bib Cock 15 mm nominal size

..do..(d)Angular stop cock with long thread 15 mm nominal size

..do..(e)soap dish

Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for soil and waste discharge system (IS:13592 : 1992 Marked) of approved quality/ make : (a)75mm dia

..do..(b)110mm dia

Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for soil and waste discharge system (IS:13592 : 1992 Marked) of approved quality /make(a)Bend 87.5 Dg. 110mm dia

..do..(b)Door Bend 87.5 Dg. 110mm dia

..do..(c)Single Tee 110mm dia.

..do..(d)Nahni trap without jali 4" 100mm dia.

..do..(e)Vent Cowel 100mm, 100mm dia.

Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size :(a)15mm dia nominal bore

..do..(b) 25mm dia nominal bore

Providing and fixing of suspended false ceiling in the grid of 600 x 600 mm/ 600 x 600 to 900 x 900 mm using aluminium tees with inter lock system of main tee, cross tee and wall angle (size of tee and angle approx. 35 mm x 25 mmx 0.5mm or equivalent) etc. complete with G.I. Adjustable suspenders skeleton, Ceiling tiles made from multi chamber hollow PVC section having an overall cross section of:- Provding & installing metal in Tile 600 x 600 mm perforated false ceiling system exposed on T" grid system. Panel shall be fabricated from 0.56 mm thick (TCT) Aluminium and powder coated on external surface shall have flange on all four sides to reiforcement exposed grid system to given 600x600 mm centre to centre of T . Panels will be plain for flush look with T ; Tiles shall haw 2.5mm dia at 5mm centre to centre in square pattern. rhe T shall be hot dipped GS Tee section 3600 mrn long main Tee 24mm wide, Cross Tee 1200 mm & Cross Tee 600mm to form grid of 600x600mm. rhe installation to be carried out with main runners spaced at 1200mm centres securely fixed to the slab / Truss by means of Roll Plug and 4mm dia G I rod at 1200 mm maximum and not more than 150mm from sliced joint. The last runner should not be greater than 600mm from the adjacent wall, 1200mm Cross Tee & 600 mm Cross Tees to be interlocked between two main Tees to form grid 600 x 600mm. Panels are then placed indi\Adually on the 600 x 600 mm exposed grid frame work created by Tee. GS edge profile shall be fixed on the perimeter of walls and columns. The carrier shall be suspended from slab by 4mm dial galvanized rod with special height adjustment power coated clips made out of spring steel at maximum 1.2 to 1.5 mtr. Centre to Centre. The 4mm dia galvanized rod shall be fixed to slab by forming one end "j" shape with roll inserts. The edge profile formed out of G.I. sheet of the size 18mm x 20mm shall be fixed on the perimeter of the walls. inclusive of Pro%Ading and fixing of Non woven Cloth, 5mm thick class wool packed in poly bag,25mm thick class wool packed inpoly Bags (Make: Pyrotech Workspace) Designer false ceiling