Jodhpur Development Authority Tender

Earth work in excavation, including stacking/disposal of surplus material with all lifts and lead upto 495 metres, excluding of compensation of earth [MoRTH specification : Clause 301 to 305] Mechanically by power shovel, including mechanical loading and carriage by tipper/dumper (6T capacity)

Carriage of Sand, bajri, ballast, stone, boulders, kankar & gravelly material includind loading & unloading ( MORTH specification : 514.5 table 500.28 ) For all km. lead and lift )

Construction of dry lean cement concrete sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm , aggregate cement ratio not to exceed 15:1 , aggregate gradation after blening to be as per Table 600-1, cement content not to be less than 150 Kg/Cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant as per mix design, transported to site, laid with a hydrostatic paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing complete as per MoRTH specification clause 601.

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with OPC 43 grade cement , coarse and fine aggregate (table 600-2 & 600-3) conforming to IS 383, maximum size of coarse aggregate 31.5mm nominal size mixed in a batching and mixing plant as per approved Mix design to achieve required design mix grade of controlled concrete, transported to site, laid with a slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler bord , separation membrane, sealant primer, joint sealant (Table 600-4), debonding strip, dowel bar (IS : 432 Grade-I), tie rod (IS : 1786 Fe500 or IS : 432 Grade-I) , admixtures (IS : 9103 & IS : 6925) as approved, curing compound, finishing to lines and grades as per drawing including joimt cutting & texturing etc complete as per MoRTH Specification cl. 602 (with flexural strengthe minimum 4.5 MPa).

Providing and laying granular sub-base material having P.I.not more than 6, including spreading in layers not exceeding 150 mm compacted thickness and consolidation by 8-10 tonne power roller to required camber and grade including cost of water and hire charges of machinery, including T&P with all lead (Compacted thickness to be measured).as per MORTH specification table 400-1, 400-2 : For grading-III with CBR value not less than 20. to attain 100% proctor density.

Providing, laying, spreading and compacting stone aggregate of specfic as per table 400-6 to Water Bound Macadam specification including spreading in uniform thickness, hand packing roll-ing with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening and binding materials to fill-up the interstices of coarse aggregates watering (with water browser) and rolling making necessary earthen bund to protect edegs, lighting, guarding, barricading and maintenance of diversion etc. [MoRTH specfication : Clause 404] By Manual Means Grading I , 63 mm to 45 mm @ 0.91 cum per 10 Sqm for compacted thickness of 75 mm. (Crusher broken) Grading I , 63 mm to 45 mm @ 0.91 cum per 10 Sqm for compacted thickness of 75 mm. (Crusher broken)

Providing, laying, spreading and compacting stone aggregate of specfic as per table 400-6 to Water Bound Macadam specification including spreading in uniform thickness, hand packing roll-ing with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening and binding materials to fill-up the interstices of coarse aggregates watering (with water browser) and rolling making necessary earthen bund to protect edegs, lighting, guarding, barricading and maintenance of diversion etc. [MoRTH specfication : Clause 404] Grading II, 53 mm to 22.4 mm, @ 0.91 cum per 10 Sqm for compacted thickness of 75 mm. (Crusher broken)

Providing and applying primer coat over prepared surface or granular base with bitumen emulsion as per IS: 8887 & manufacturer’s specifications @ 6 kg /10 sqm with a self propelled of towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI 502,112 ( Including cleaning of road surface )

Providing and applying tack coat on the prepared surface ,with bitumen emulsion as per IS : 8887 & manufacturer’s specifications @ 2 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface )

Providing and laying Dense Bituminous Macadam on prepared surface with specified graded crushed aggregates as per table 510 and design mix for base/binder course including loading of material with F.E loader heating of binder aggregate and filler in approved hot mix plant as per clause 6.5 of manual transporting the mixed material by tippers and laying with sansor paver finisher as per clause 505.3.5 to the required level and grade rolling by self propelled power rollers and vibratory rollers or pneumatic tyred roller 150-250KN. TP=0.7MPa to achieve the desired density (approved by the department) but excluding cost of primer/tack coat. [MoRTH Specification : Clause 505,112] Grading II (19 mm nominal size) - Bitumen @ minimum 4.5 % of mix (VG-30 grade) & thickness 50 - 75 mm

Providing and laying bituminous concrete as per design mix on prepared surface with specified graded stone as per table 500-16 for wearing course including loading of aggregate with F.E loader and hot mixing of binder and 2% cement filler with aggregates in approved hot mix plant as per clause 6.5 of manual Transporting the mix material with tipper to paver and laying with sensor paver finisher (as per clouse 507.3.5) to the required level , grades and rolling with vibratory compactor and pneumatic tyred roller 150-250 KN,TP=0.7 Mpa, to achieve the desired density (approved by the department) excluding cost of primer/tack coat (MORTH Specification : Clause -507,112) Grade-II Bitumen @ 5.4 % of mix With lead of mix material 1 KM VG-30 grade

Providing and laying mechnically mixed and vibrated Cement Concrete in foundation upto a depth of 1.5 metres below ground level and 1.50 metres above Ground/Bed level.[MoRTH Specification : Clause 1000/1700] Cement concrete 1:3:6 mix crushed stone aggregates 20mm nominal size.

Structural cement concrete (Design Mix) in open foundations, with form work, at any level. Cement concrete for plain/reinforced concrete in open foundation as per drawing and technical specification. [MoRTH Specification : Section 1700(N)&1500(N)]. P.C.C.M40 grade

Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Thermo-mechanically Treated bars (Conforming of relevent IS code)

Making connection of G.I. distribution branch with G.I. main including all fitting. Upto 25mm dia

P&F rigid PVC Pipe (IS:4985 mark) class II(4 Kg. /Cm.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant 110mm dia

Providing and laying of hot applied thermoplastic compound inclusive type I reflectrosing glass beads as per table 800-9, 800-10 applied in uniform thickness of at least 2.5 mm and spread uniformly with reflectorising glass beads type II in addition @ 250 gms per Sqm with a road marking machine as per IRC: 35 complete with traffic diversion arrangement as per MORTH specification clause 803.4

Painting two coats after filling the surface with synthetic enamel paint in all shades on plastered concrete surfaces as per MORTH specifications Cl. 803. Old surface

Providing and fixing of retro- reflectorised inclusive cautionary, mandatory and informatory sign as per IRC-67 made of high intensity grade sheeting lettering, border & signs fixed over aluminium sheeting, 1.5 mm thick, fixed on mild steel angle iron frame 50mmx50mmx6mm supported on a mild steel angle iron post 75mmx75mmx6mm upto the top of sign board, length of post from bottom of sign board is 2.85m. upto foundation level post duly painted in black & white synthetic enamel. fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45 Cm x 45 Cm x 60Cm, 60 cm below ground level as per approved drawing & as per MORTH specification Cl. 801.

60 Cm equilateral triangle

80 cm x 60 cm rectangular

60 Cm circular