Jaipur Zila Dugdh Utpadak Sahakari Sangh Limited Tender

Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints and cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement. for Beems, suspended floors, roofs, griders having slopes upto 15degree , landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and sprial staircases etc. M20 grade nominal mix / Design mix.

Providing & fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. Thermo mechanically Treated bars (Conforming of relevant IS code)

Centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for suspended floor, roofs, landings, staircase, balconies, girder, cantilever, coping, bed plate, sills, chhajja, lintel, beam, plinth beam etc.

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish. 20mm thick

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish. 12mm thick

Providing & fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Green / Black above 3601 Cm2 slabs.

Extra for providing edge moulding to 15-18mm thick marble/Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite work).

Extra for fixing marble/granite stone over and above corresponding basic item, in facia and drops of width upto 150mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering. All work up to plinth level. M10 grade Nominal mix 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

P & F 1st quality Vitrified Porcelain Polished tiles on floor, skirting and steps etc. in different sizes (thickness to be specified by manufacture) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all color and shade, laid with 20mm thick CM 1:4 including grounting the joints with white cement and matching pigment etc. complete size 600mm x 600mm.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work including preparation of base with primer, putty, lippy etc. complete in all respect (Inner surface).

Painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty etc. complete in all respect. New work

Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitered welded and grinded including hold fast of steel lugs 13mm x 3mm and 15cm long embedded in CC block 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15mm paitam of 18 gauge thickness, joint mitered and grinded including 10mm x 10mm square bars welded to frame for paitam fixing float glass 4mm thick panes with glazing clips and metal sash putty and fixing of shutters frames peg stay, U shape handle 100mm long, tower bolts 100mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in-charge. Window openable.

Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance.

Providing and fixing square bars or other flat welded to window, ventilators etc.

Providing and fixing calcium silicate perforated board false ceiling at all heights including providing and fixing of frame work made of special sections power pressed from M.S. Sheet and galvanised in accordance with zinc coating of grade 350 as per IS: 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm dia x 40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction including fixing the calcium silicate board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screw @230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting of thickness of calcium silicate board as below: 8 mm thick

Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jamb, lock jamb, bend and if required angle threshold of mild steel angle of section 50 x 25mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4 (M15 grade) complete as directed by Engineer-in-charge: Profile E

Providing & fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehydration in glue both sides with approved steel fittings complete as per annexure ‘A’. 30mm thick. Decorative teak veneer one side.

Extra for providing external lipping with 2nd class teak wood battens 6mm minimum depth on all edges of shutters (over all area of door shutter to be measured) over item.

Extra for providing other type of fitting as mention in annexure A (As approved by EI) stainless steel fittings.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Providing & fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gap at junctions at top bottom and sides with required PVC/neoprene felt etc. Aluminum section shall be smooth, rust free, straight mitered and jointed mechanically wherever required including cleat angle. Aluminum snap beading for glazing/paneling, C.P. brass/stainless steel scerws AI. Tower bolt & AI. handle & AI. drop etc. all complete as per architectural drawings and the directions of Engineer – in –charge (Glazing and paneling to be paid for separately) Powder coating aluminum (minimum thickness of powder coating 50 micron).

Providing & fixing 12mm thick pre-laminated three layer medium density (exterior grade) particle board grade 1, Type II conforming to IS: 12823 bonded formaldehyde synthetic resin of approved brand and manufacture in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Pre laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing & fixing glazing in aluminum door, window, ventilator, shutters and partitions etc. with PVC/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminum snap beading shall be paid in basic item) with float glass panes of 5.0mm thickness (weight not less than 13.50 Kg/Sqm).