Jaipur Vidyut Vitran Nigam Limited Tender

S&F MS clamp set of 50x6mm flat from Iron with nuts & bolts etc. for holding the riser pipes assembly of submersible pump set .(P/2.22)

S&F tube well cover of MS sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with GI Nipple 45cm long & two GI flanges at both ends in 80mm sizes passing through a hole in the centre of MS sheet. A 25mm socket with end plug shall also be welded over top plate. A GI nipple having outside thread of size 1/2" (for installation pressure gauge) shall be provided & welded with 80mm GI nipple near top plate nipple shall be provided with end plug. 200mm.(P/2.23.3)

P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 6.0 Sq.mm 3 core flat / Round (E/4.7.4)

Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 12mm (suitable up to 50 mm OD pipe). (E-21.3.1)

Supply of ERW M.S. black casing pipe ISI marked (IS : 4270 / 2001) or amended upto date of following sizes. 200mm dia NB (thickness of pipe 5.4mm & mass of tube 28.46 kg/m). (P/2.11.2)

150mm dia NB (thickness of pipe 5.0mm & mass of tube 20.13 kg/m). (P/2.11.1)

Labour charges for making slots on blank pipes made of ERW MS black pipe ISI marked of following sizes, the slotting should be as per IS 8110:1985.150mm dia nominal bore of 4.8mm thickness.(P/2.12.2)

SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively.3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM Copper Wound . (E/21.6.1.4)

SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .For single phase Submersible / Monoblock pump 2.0 HP to 3.0 HP (DOL starter) .(E/21.13.1.2)

Providing and fixing 3-layer PP-R (Polypropylene random coplymer ) pipes SDR 7.4 UV stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of Engineer - in charge. (EXTERNAL WORKS) (A) PN-16 Pipe, 25 mm OD. (S-2.36.3)

(B) PN-16 Pipe, 32 mm OD. (S-2.36.4)

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : (A) Gun-metal 25 mm nominal bore.(S-2.15.3)

(B) Gun-metal 32 mm nominal bore. (S-2.15.4)

P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: (A) 500 Liters capacity. (S-2.26.3)

P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball complete : Brass wt.Not less than 400 gm, 20mm. (S-2.11.2)

Development of tube well having depth up to 250 mtr as per IS: 11189- 1985 and IS: 2800 (Part- I)- 1991 (both amended up to date) using suitable methods to give sand free water for required yield of the gravel packed tube well. (P-2.10)

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock, (A)15mm nominal bore. (S-2.7.3)

Deepening of existing tube well by DTH system beyond existing depth upto 100 mtr. Andabove in all type of rocks including flushing of tube well and obtaining sand free water.Nominal bore 150 mm dia.(P-2.7.1)