Jaipur Smart City Limited Tender

Providing, lowering, laying, aligning, fixing in position and jointing atall level/ depths full round HDPE DWC (double wall corrugated) pipes of SN8 grade as per IS 16098 (Part 2) amended upto date in trenches in complete including all material, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications, drawings and as per direction of Engineer.:150 mm ID

Maintenance free gel earthing with pipe in pipe / Strip in Pipe technology filled with anti corrosive conductive compound (CPRI tested) below the ground in 150 -200 mm dia earth pit and surrounding filled with required mineral filling compound (MFC should have hygroscopic proper ty to retain the moisture for long time to create low resistance Zone) and C.C. finished chamber covered with hinge type with locking arrangement C.I cover. C.I. frame of size 300mm x300mm complete testing of earth resistance as required of following sizes With pipe in pipe technology (inner pipe dia / outer pipe dia) 80 -100 micron G.I. coating: G.I. pipe 3000 mm long , 80/40 mm , terminal 14 mm G.I. strip

S & Laying following size earth wire/strip in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection etc. as required. :25mm x 3mm G.I. Strip

S & Laying following size earth wire/strip in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection etc. as required. : 50mm x 6mm Alum. Strip

S & Laying following size earth wire/strip in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection etc. as required. : 8 Swg GI Wire

Providing & Laying XLPE insulated IS:7098/II/85 of approved make H.T.cable for working voltage 11 K.V.Earthed with Stranded Compacted Circular Aluminium Conductor, Conductor Screened with Extruded Semi-conducting compound, XLPE Insulated, Insulation Screened with extruded semi-conducting compound in combination with Copper Tape, cores laid up, inner sheath of Thermoplastic tape, galvanised flat steel strip armoured and overall Extruded PVC Type ST- 2 Outer Sheathed cable direct in ground including excavation of 30cmx100cm size trench, 25cm layer of river sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection testing etc.as required of size.: 3 core 185.0 Sq.mm

Providing & Laying XLPE insulated / P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-I/1554-1 approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size :185.0 Sq.mm, 3.5 core

Providing & Laying XLPE insulated / P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-I/1554-1 approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size :70.0 Sq,mm, 3.5 core

Providing & Laying XLPE insulated / P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-I/1554-1 approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size :10.0 Sq.mm, 4 core

Providing & Laying XLPE insulated / P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-I/1554-1 approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size :16.0 Sq.mm, 4 core

Supplying and making one end termination with heavy duty double compression brass gland SIBG type, aluminium lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size: 3.5 x 70.0 sq.mm

Supplying and making one end termination with heavy duty double compression brass gland SIBG type, aluminium lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size: 3.5 x 185.0 sq.mm

Supply, Installation, Testing & Commissioning of HT metering cubical panel as approved By DISCOMs fabricated out of 14 SWG CRCA sheet steel in two compartment & MS angle of size 60mmX6mm having provision for Following: (I) Provision for fixing Trivector Meter (To be supplied by DISCOMs) (ii) Provision for fixing of combined CT PT Set (To be supplied by DISCOMs) (iii)TT Block (iv) 6mm Bakelite sheet on all sides.

SITC of walll / free standing floor mounted dust and vermin proof compartmentalised cubical panel made out of CRCA sheet, required hardware, duly painted by two coats of zinc / red oxide primer followed by Powder coated / epoxy / PU painted with phosphatisation in grey or required shade after rinsing. The panel having PU / Neoprene rubber gasket of not less than 3mm thickness, separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. Thickness of sheet shall not be less than 1.6mm up to 600mm length/width of any compartment and be of 2.0mm above 600mm. Load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Side walls and cable alley compartments having bolted type doors with detachable extension type structure (only outer area on all sides shall be measured and panel to be fabricated from CPRI approved fabricator).

Supplying and fixing of Aluminium / Copper bus bar by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves: Electrolytic grade aluminium bus bar

SF of (0-500) V range Volt meter on existing panel, making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required.:Digital type

SF of CT operated direct reading type Ampere meter on existing panel , making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required.: Digital Type,Above 500 A

SF of Current Transformer , with all necessary support in existing panel including connection etc. as required .: from 500 / 5 to 1600/5 Ratio , 15 VA , class 1 accuracy

SF of 240/220 V, LED (22.5 mm dia ) Pilot lamp with integral circuit, terminal block, including connection etc. as required.: Red / yellow / Green colour

SF of 240/220 V, LED (22.5 mm dia ) Pilot lamp with integral circuit, terminal block, including connection etc. as required.: Blue colour

P & F of energy analyser (multy function energy meter) with LCD / LED display capable of minimum 20 numbers electrical parameters display with 1A/5A CT input for LV/ HV network, RS 485 communication port etc. complete in all respect.

SF of rubber matting with one side corrugated as per IS specifications 15652 / 2006 : 3.3 KV, 20 mm thick,

SITC of microprocessor based intelligent power factor correction relay having sensitivity up to 50 milli Amp secondary current and following way, self analysing auto c/k setting according to targeted power factor setting, the relay shall have minimum three digit display unit for display of real power factor, targeted power factor, lag / lead capacitor switching status, alarm output for under current, over current, insufficient compensation, indication of switching on units, auto / manual status, and shall have over load protection, no volt release etc. as required.: 6 to 14 stage - sensitivity up to 50 milli Amp. (Prefer 12-14 Stage)

P & F of ac operated heavy duty 230 /440 Volt power contactor conforming to IS:13947-4-1 / IEC:947-4-1having provision of mechanical interlocking, Din rail mounting type including making connections, testing etc. as required. :21 to 25 Amp

P & F of ac operated heavy duty 230 /440 Volt power contactor conforming to IS:13947-4-1 / IEC:947-4-1having provision of mechanical interlocking, Din rail mounting type including making connections, testing etc. as required. : 26 to 32 Amp

P & F of 440 Volt 3 pole capacitor (AC 6 B ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors / reactors to limit the inrush current, conforming to IS:13947-4-1 / IEC: 947-4-1, Din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank.:11 to 20 KVAR

P & F of 440 Volt 3 pole capacitor (AC 6 B ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors / reactors to limit the inrush current, conforming to IS:13947-4-1 / IEC: 947-4-1, Din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank. : 21 to 30 KVAR

SITC of fixed / Draw out type 4 pole Air Circuit Breaker conforming to IS 13947/IEC 60947 P-2 in existing LT panel suitable for LT installation 440 V, 50 Hz and having adjustable short-circuit, earth fault and over load MICRO PROCESSOR release with LCD display, bargraph and separate LED indication for each type of fault, at least 4NO & 4NC auxiliary contacts safety shutter and fault position acknowledgement mechanism type, ACB shall have separate indication for service, test, isolation, maintenance position including making connections etc. as required. : Fixed type, 800 A Rating , 50 kA

SITC of quick make and quick break 4 POLE current limiting MCCB having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings and conforming to IS 13947-2 / IEC 60947- 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for UVR , shunt trip ,earth fault trip, push (test) to trip , including making connections with lugs / spreaders etc. as required . : up to 100 Amp, 35 kA, adjustable O/L & adjustable S/C setting

SITC of quick make and quick break 4 POLE current limiting MCCB having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings and conforming to IS 13947-2 / IEC 60947- 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for UVR , shunt trip ,earth fault trip, push (test) to trip , including making connections with lugs / spreaders etc. as required: 200 Amp,35kA,adustable O/L & adustable S/C setting

Providing and fixing testing and commissioning of Kiosk type weather proof distribution feeder pillar box of size 600 x 450 x 1000mm with a taper of 75mm at top ( for protection from rain water) and made out of 3.2 mm (10 gauge) thick CRCA MS Sheet, front and back both side openable, duly hinged doors with locking arrangement by providing both sides hold drafts and all hardware for fabrication of box. The cubical panel should be dust and vermin proof followed by two coats of enanel paint and primer. The cubical panel should be mounted with hardware on angle iron frame 40 x 40 x 6m and 600mm long legs duly primered and black painted. Frame be grouted with cement concrete 1:3:6 ratio in 150 x 150 x 750mm and providing brick masonry along angle iron frame above ground level. The panel should comprise of as per following : (a) P/F of 2 Nos. knife switch 400 amp. with U contacts studs and washers etc. (b) P/F of 32 amp Category-I make MCBs, 10 Nos.double pole. & 5 nos TPN . (c) P&F of connecting strips of 63 amp. 4 pole. (d) Backelite sheet 10mm thick and size 3'x2'. (e) Epoxy insulators 40mm: as per requirement. (f) PVC copper wire 10 sq.mm. flexible connecting to bus bars to MCB's and MCB to connectiong stips in proper manner. (g) copper bus bar double and D-Type of size 30 x6mm strip approx. 1.5' long, 8 no. with hardware. (h) Provision of cable clamps at side of box and base plate with cable glands of suitable size

MAIN CUBICAL PANEL / STREET LIGHT CONTROL PANEL P/F testing & commissioning of kiosk type weather proof out door main cubical panel size 750 mm X 1250 mm X 500 mm (app.) made out of 14 gauge MS sheet front and back both side openable duly hinged door with locking arrangement by providing both side held draft and all required hard wares. The cubical should be dust and vermin proof followed by coat of zimpholite primer and finally two coats of enamal gray paint. The cubical should be mounted with hard ware on angle iron frame size 50 X 50 X 6 mm and 1500 legs duly painted framed be grouted 750 mm below ground level with cement concrete 1:3:6 in 1000 X 500 X 600 mm and providing brick masonary along angle iron frame above G.L. They shall be in two section comprising as follows: (i) Providing & Fixing 415 V ,TP combination double break HR switch fuse unit .100 Amp. rating for incoming supply with HRC fuse 100 Amp rating and of BCH/L&T/EE/ Siemens/ ABB make. (ii) Providing fixing timer switch TSQ 100 series 240 Volts, and full running service standred mounting with base of L & T or equivalent make including the cost of contactor 63 amp. 50 Hz. 440/400 volt. (iii) P/F open busbars 25mmX3mm of required length duly covered by heat shrinkable sleeves with busbar supporters (iv) Provision for residual current operated 63 Amp. 1 Pole ELCB of 30MA to 300 MA sensitively as required including making connections etc.(EE/Load stop make) (v) P/F 2 Nos. 415 Volts TPN combination double break switch fuse unit,63 Amp. Rating with HRC fuses (EE/mds/ SCHNEIDER bch/Siemens )for outgoing cable and making connection etc. also to have a provision for two nos. above switchs. (vi) P/F of 3 nos. RYB phase indicator resitance type complete with lamp P/F of HT danger plate of size 200 X 150 mm made of aluminium sheet 20 gauge. (vii) P/F cable glands double compression type and Al. lugs duly crimped for incoming cable and out going Cables. (viii) Providing 2 Nos. earth terminals including lugs and H/W duly inter connected with 8 SWG copper wire . (ix)Inter connection of main busbar to each out going switch and cable terminal shall be with 4 sqmm PVC copper conductor duly crimped with AL lugs. (x) Cable termination shall be fixed at backside of the panel with H/W and spring washers (xi) Light control switch with photo senser complete unit as required

Supply, Fabricating & installing following sizes of perforated cable trays including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with suspenders and including painting as required : Hot Dipped Galvanized, 150mm x 50mm x 1.6mm

Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead up to 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level.In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.Depth up to 1.5 m

Brick work with FPS bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 12mm cement plaster of mix :1:4 (1 cement : 4 fine/ coarse sand)

Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work up to plinth level :1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size). (As per design mix)

Centring and shuttering with plywood or steel sheet up to two stories or height up to 7.5 metre above plinth level including strutting, propping etc. and removal of form for :Edges of slabs and breaks in floors and walls. Under 20 cm wide

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size).

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

Providing & fixing UV stabilised fibreglass reinforced plastic sheet roofing up to any pitch including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2"or 3"or 6") as specified.

Supplying and fixing of GI chain link fencing of required width in mesh including strengthening with 2 mm dia GI wire/ G.I. staples/ G.I.U-nails/ nuts bolts with 2.4 m angle iron posts 50 mm x 50 mm x 6 mm placed every 3 metres centre to centre founded in M15 grade cement concrete 30cmx30cmx60cm, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only etc complete as required and as per direction of Engineer-in-charge. Mesh size 50mm x 50mm made of GI wire 3.15mm dia

Providing & making heat shrinkable type indoor/outdoor/straight through terminations/joint kit of approved make suitable for XLPE insulated 11 KV cable, with required components, prepration of cable ends, testing etc. as required of following sizes .: Outdoor, 3 core 120/150/185/225 Sq.mm

Supply and fixing of 11 kV, 400 Amp, 3- phase, central post rotatingdouble break type isolator (IS:9921 part I to V) without earth bladegang operated horizontal type switch, operating mechanism with GIspring loaded reverse loop type fixed contact, solid hard drawn electolytic copper tubular moving contact with silver/ nickel plated at end points, 9 nos post insulator of 12 kV (IS:2554 & IS 5350 part III), hot dipped galvanising hard ware, GI pipe, nut, bolts etc complete in all respect as per specification of Discom.( Type tested by ERDA/CPRI.)

Supply and fixing 100 Amp, 11kV Horn gap fuse set IS 9385 onexisting DP structure with 6 nos 24kV/22kV post insulator (IS:5350 part III), hot dipped hard ware,fuse wire of required size etc. complete in all respect as per specification given by Discom. (Type tested by ERDA/CPRI)

Supply and fixing of distribution type Lightning arrestor 9 kV, 5 kA (IS:3070) with mounting base to be installed on existing DP structure. (Type tested by ERDA/CPRI.)

Supply and fixing double pole structure for 11/0.4 Kv substation as per Discom specification complete in all respect as required including nuts and bolts etc (excluding the cost of poles) made of MS channel of 4 nos 100 x 50 x 6mm and 4 nos 75 x 40 x 6mm and MS flat 50 x 6mm as per Discom specifications.

Providing and fixing of single pole mounted structure set for isolator as per Discom specification complete in all respect with nuts and bolts as required MS flat 50 x 6mm, MS angle 65 x 65 x6mm, MS channel 100 x 50 x 6mm. ( Excluding cost of pole ).

Supply and fixing of 11 kV Danger plates as per specification of Discom on the existing poles complete in all respect as per Discom specification.

S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface / recessed using saddles, clamps, fastener as required including cutting the wall and making good the same as required, 25 mm

P & F of IP20 LED Recessed/ Surface Mounted Round/ sqaure Non Dimmable Downlight with die-cast aluminum housing & Heat sink for heat dissipation, high purity reflector with external driver having efficiency 85% and in compliance to IEC standards. ( supplied together with luminaire) Power consumption of = 7w/10w/8w/12w/15w/18W with 100/500/750/1100/1250 lumens, system lumen, efficeancy of 70 lm / Watt or 100 lm / Watt output suitable to replace 1x18W/ 2x18w/2x26w CFL downlights, life time of 50000 Burning Hours with 70% of intial Lumen maintained. CCT 3000° K, 4000° K and 6000° K. Fixture shall be CE Compliance.: LED downlight 9/10/12 W

Supply and erection of Decorative/ Heritage Cast Iron pole as per approved design of following length with base plate onthe cement concrete foundation of M-15 grade (1:1.5:3) with the help of anchor bolts of grade 6.8 (IS 1367 P III). The pole shall be made of Cast Iron as per IS 210:1993, precision machining and filling job to achieve good finish and a fine coat of primer on each element before assembling. After assembling of each element one coat of primer and two coats of P.U. paint are applied. Approved coloured UV resist coating of mat/ glossy/ metallic finish followed after air drying of pole. The pole shall have a weatherproof flush door and locking arrangements, two/ one arm bracket of length of 430/380mm complete in all respect. : 6.0 Mtr

P/ F IP-65/ IP-66 protected street light luminaries on existing bracket. Fixture made from powder coated single piece pressure die cast aluminum housing with heat dissipation fins on housing with high power LEDs . Diffuser / glass cover for ensuring IP-65 protection for lamp and control gear compartment, system lumen output of 100 lum/watt high power LED. Integrated driver shall be high efficiency having efficiency more than 85 % and in compliance to IEC standards. System life of 50000 burning hours with 70 % of initial lumens maintained. Fixture shall be in CE compliance. :Warm White, BRTFG 45W LED WW

P & F of IP68, IK10 protected LED Buried marker light / Step Light Fixture. Fixture made of powder coated die cast alluminium with Toughened Glass cover and appropriate beam angle lens to be used as per requirement. The System level Luminous efficacy must be 90 Lumen/W. High Power LEDs at 1W/2W per LED. The driving current should be Minimum 350 mA per LED. CRI70, CCT: 3000/6500 K. The integral SMPS based electronic driver must be constant current and surge protection of min. 4KV(L-N) and efficiency 85%, PF0.9 and input Voltage range of 90-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained. Light should include quick connecting cable coupled with various mounting accessories. Light output in Cool white or Warm White Colour as per engineers choice. Fixture must be in compliance with IS/CE Standards. : Burial Light - 10W

P & F of IP65 IK10 protected LED Bollard fixture. Light Fixture made of powder coated alluminium/Steel housing with diffuser for uniform distribution. The System level Luminous efficacy 85 Lumen/W. SMD LEDs . CRI70, CCT: 3000/4000/6000 K. The integral SMPS based electronic driver must be constant current and inbuilt surge protection of min. 4KV(L-N) and efficiency 85%, PF0.9 and input Voltage range of 90- 270V AC at 50Hz. System life of 50000 burning hours with 70% of Initial Lumens maintained. Light should include quick connecting cable coupled with various mounting accessories. Light output in Cool white or Warm White Colour as per engineers choice. Fixture must be in compliance with IS/CE Standards.: 1.0 Mtr Bollard

Supply and erection of Octagonal pole of following length and dimension as per table-3 with base plate on the cement concrete foundation of M-15 /M-20 grade (1:1.5:3) with the help of anchor bolts of grade 6.8 (IS 1367 P III ). The pole shall be made of S-355JO grade steel sheet , folded lengthwise to obtained Octagonal shape, having single longitudinal seam weld and hot dipped galvanised internally & externally in accordance with IS 2629. The pole shall have a weatherproof flush door and locking arrangements. The complete work shall be supervised and certified by the manufacturers for satisfactory supply, erection, testing and commissioning.: 7 Mtr.

Supply, Erection and Fixing of hot dipped galvanised Overhang (60 X 3.25 mm) with cap (250 x 137.9 x 4.05 mm) over the existing poles : Single arm overhang

Supply, Erection and Fixing of hot dipped galvanised Overhang (60 X 3.25 mm) with cap (250 x 137.9 x 4.05 mm) over the existing poles : Double arm overhang

Supply, Installation, Testing and Commissiong of indoor type floor mounted metal clad, 11 KV Incomer VCB panel up to 630 A equipped with following switchgears and accessories designed & tested as per latest standard i.e. IEC 62271-200, suitable for STC 25KA/3 and IAC A-FLR for 25kA/1sec. Make of HT Panel, Vaccum Interrupter and VCB should be of same make. 11 KV / 110 Volts PT Class 0.5 accuracy and 100 VA burden with 1No. Voltmeter (0-12 KV), analog type, selector switch for voltmeter and protection fuses/MCB for HT metering upto 12 KV on incomer, Ammeter, analog type, selector switches for ammeters, Microprocessor based numerical relay with O/L, E/F and S/C protection, Set of dual core dual ratio 3CTs of suitable ratio with sec 1 of 15 VA burden and accuracy Class – 0.5 for metering and class 5P10 for protection, Multifunction Meter.

46.1 P&F 240/415 V MCB of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections with lugs, testing etc. as required, 6 A to 32 A rating.

P&F flush/surface type enclosure for housing MCB/Isolator with Din rail including making connections with lugs, repairs etc. as required. : With sheet steel enclosure, One /two way

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required 2 x 1.5 sq.mm

S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface /recessed using saddles, clamps, fastener as required including cutting the wall and making good the same as required 20 mm

Supply , Drawing and Testing of 4 pair, 100 ohm, 24 AWG UTP Cat 6 Cable as per latest ammendments of TIA /EIA 568 B.2-1 Specifications in existing MS/PVC Conduits including making connections to Information outlets and Patch Panels with ferruling at both ends for identification with necessorry tools for punching, stripping, crimpping and testing required .