Jaipur Development Authority Tender

Supplying and fixing of Single Molded twin Shank Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97-DO III Dt 11.06.1997. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35+/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 700 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. (manufactured from 3M, Avery or equivalent)

Supplying & Installation of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered, LED self illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The marker shall support a load of 20000 kg jested in accordance to ASTM D-4280. The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinking is 1 Hz. There should be current losses of less than 20 micro-amperes at 2.4 V in sleep-charging mode to enhance the life of the marker and a full charge should provide for a minimum autonomy of 50 hours. The height, width and length of the marker shall not be less than 10 mm X 100 mm X 100 mm. Also the surface diameter of the marker shall not be less than 100 mm respectively. The weight of the marker shall not exceed 0.5 Kilograms. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy rasin based adhesive as per manufacture’s recommendation and complete as directed by the engineer. (manufactured from 3M or equivalent)

Providing and fixing SOLAR DELINATOR made of ms pipe of 48/63 mm, dia upper top of iron cage 1 Meter Pole Energy: green led warning strobe light 3.2 Volt 600 mAh Illumination: 4 High Intensity Super Bright LEDs Cover Material: PC Function: flash- stable -close 6 Hour Sun Charged: Operates 60 Hours (Flash Mode) Photocontrol: Automatic on at Dusk; Off at Dawn (Flash Mode) Photocontrol: Automatic on at Dusk; Off at Dawn IRC 67 2012 and meeting the coefficient of retro reflection values as per ASTM D 4956 Type XI table specification. The delineator shall be painted with powder coat of minimum 40 microns thickness, on top of which The structure shall be manufactured in roll forming process and shall have height not less than 800 mm above the ground, dia of ms pipe 48/63 MM DIA and shall extend not more than 50 mm below the ground while being installed

Providing & fixing 3M radium tape of approved colour & Design complete in all respect as per instruction by Enginner in Charge

Providing & Fixing of median marker made of tough high impact resistance injection moulded thermo plastic body with an isosceles trapezoidal structure of length, height & width not less than 12cm, 10cm respectively and thickness not less than 1.8mm. The median marker shall have flourescent yellow colour retro reflective sheeting of size not less than 8.5cm X 8.5cm and with fully reflective micro prismatic as its retro reflective elements and meet ASTM D4956-09 Type XI specification. The retro reflective sheeting shall be on both the sides of the median marker and shall be as protected with no exposed edges that prevent edge lifting, vandalism, sheeting damage etc. The median marker shall be fixed with a combination of epoxy adhesive and grouting etc. complete as directed by the Engineer -In-Charge. (manufactured from 3M or equivalent)

Supply of ‘L’ type Bollard made out of 1.25 mm thick M.S. sheet height 134 cm, welded in circular type ring section having upper dia 15 cm. and lower dia 21 cm with another attachment of 15x15 cm circular section with 15 cm. face plate and hold fast at bottom, whole body is processed in white stoving enamel and red reflective 3 hands, each of 7.5 cm end one reflective sheet of 15 cm. dia provided to it complete in all respect.

Supply of Hazard Marker made out of 2 mm thick M.S. sheet size 300x300x3 mm framed with angle iron 25x25x3 mm and fixed on channel posts 75x40x6 mm and hold fast at bottom whole body is painted in white stoving enamel and 6 Nos., 5 cm dia reflective sheet on white reflective background with additional border of 1.25 cm all arount it.

Repairs to Building Providing and laying treatment of wear & tear concrete surface with pre-mixed, ready to use, geo polymer based mortor & confirming to ASTM C: 1600 upto 10mm thickness with following property- Curing free, compressive strength of 15MPa within 2hours, Quick setting, Bond strength of 4MPa within 24hours and repaired surface should be ready to use within 3hours. (This item is to be used in only emergency situation after decided by Engineer in charge)

Painting & Artistic work of various color (Chitrakari) with drawing flower & leaves, bail, butta exterior paint including of all material etc. as per direction of engineer incharge