Jaipur Development Authority Tender

Painting (one or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour on old work : 100 mm diameter pipes

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work.

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling course below open foundation of Head walls as per drawings & MoRD Specification Clause 1109 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and MoRD specifications P.C.C grade M 10 Nominal mix 1:3:6

Interlocking Concrete Block Pavement with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge Blocks (measurments shall be made inner to inner side of edge blocks) Providing and Laying of Interlocking M-30 grade Concrete BlockPavements having thickness 100 mm as per drawings andMoRD Specification Clause 1504with M-30 Grade 0.30 Mtr x0.30 Mtr x 0.15 Mtr Edge Blocks. Category 'B' : Dentated only two side like I,Z,T shape as per

Providing and Laying of Interlocking M-30 grade Concrete Block Pavements having thickness 80 mm as per drawings and MoRD Specification Clause 1504with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge Blocks. Category 'B' : Dentated only two side like I,Z,T shape as per

Supplying and fixing of Single Molded twin Shank Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lensface and shall support a load of 16000 kg tested in accordanceto ASTM D 4280 Type H and complying to Specifications ofCategory A of MORTH Circular No RW/NH/33023/10-97-DO IIIDt 11.06.1997. The height, width and length shall not exceed50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35+/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 700 Kgf. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer. (manufactured from 3M, Avery or equivalent)

Supplying & Installation of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered, LED self illumination in active mode, 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The marker shall support a load of 20000 kg jested in accordance to ASTM D 4280. The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinking is 1 Hz. There should be current losses of less than 20 micro-amperes at 2.4 V in sleep-charging mode to enhance the life of the marker and a full charge should provide for a minimum autonomy of 50 hours. The height, width and length of the marker shall not be less than 10 mm X 100 mm X 100 mm. Also the surface diameter of the marker shall not be less than 100 mm respectively. The weight of the marker shall not exceed 0.5 Kilograms. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy rasin based adhesive as per manufacture’s recommendation and complete as directed by the engineer. (manufactured from 3M or equivalent)

Supplying & Fixing cautionary / Warning Reflective sign boardsmade out of 2 mm thick M.S. sheet as per IRC –67-1977, stoveenamelled and reflective symbol fixed on Angle Iron of size 65x 65 x 6mm of 3 meter long : 90 cm equilateral triangle

Supplying & Fixing Direction and place identification sign board made out of 2 mm thick M.S. sheet framed to angle iron 40x40x5 mm and two vertical posts of angle iron of size 65x65x6 mm 3 meter long with hold fasts, stove enameled paint reflective letter symbol complete of size. : 150 x 120 cm. Direction and Place Identification signs upto 0.9 sqm size board

Retro-reflectorised Traffic Signs Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing andMoRD Specification Clause 1701 Traffic Signs

Retro-reflectorised Traffic Signs Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRD Specification Clause 1701 900 mm equilateral triangle

Stone masonry work in cement mortar in foundation complete as per drawing and MoRD specifications clauses 702, 704, 1202 & 1203. Coursed rubble masonry (1st sort) In 1:4 cement mortar Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :

Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Plastering with cement sand mortar 1:6, 20mm thick as per 45 technical specification Clauses 613.4 & 1204

Supply of JCB (excavator cum loader) Type 3D on hire including POL & driver at different sites as Directed by Engineer in charge.

Supplying of 35 HP Diesel Tractor Trolly with hydraulic lift Trolley on hire with driver, cleaner and POL at different sites ofJDA region as Directed by Engineer in chargePer Shift of

Providing and fixing of Reinforced Ferro cement Drain cover designed for class "AA" loading duly marked on cover with adequate steel reinforcement having thickness 75 mm to 150 mm anti- corrosive bitumen painted M.S. plate Rim and on M.S. lifting hooks admixture like plasticizer bond improving compound shrinkage resistance compound abrasion resistant complete as per approved design etc.for drain Opeining Size 451 to 700 mm Standard Drain Cover Size 1000mm x 800mm x 100mm

for drain Opeining Size 701 to 1200 mm Standard Drain Cover Size 1500mm x 600mm x 125mm

Providing and fixing reinforced concrete precast kerb stone or dand R.Mtr of M-20 grade cement concrete 120 cm long having 4 Nos. bars of 8 mm dia hysd and stirrups 6 Nos of 6 mm dia as per IS with in built provision of interlocking of jointing and lifting compaction of reinforced concrete by mechanical and table vibrators jointing at site with cement mortar 1:4 complete in all respect as directed by Engineer incharge on: 100 mm thick cement concrete 1:4:8 (1 Cement : 4 Coarse sand : 8 stone aggregate 20 mm thick nominal size) including excavation of earth and cutting of BT road cutting of WBM road etc. and disposal of surplus material with all lead and lift. The size of kerb shall be (11.5+16.5)/2*30+(16.5*7.5)

Supply & fixing of M-20 grade precast cement concrete Kerb or Dand upto 60 cm length over 20 mm thick base of cement mortar 1:6 including jointing earth work, painting & jointing with cement mortar 1:4 of size (22.5 x 25) / 2 x 30 cm

Dismantling of Flexible Pavements Dismantling of Flexible Pavements and disposal of dismantled materials upto a lead of 100 m, stacking serviceable and unserviceable materials separately as per MoRD Specification Clause 202 Bituminous Courses

Building Rubbish Stone metal (Grit and ballast etc.) Add for each 1 Km beyond 5 Km(upto 10 Km.)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and MoRD specifications Clause 802, 803, 1202 & 1203 R.C.C. grade M 25

Supplying, fitting and placing TMT bar reinforcement (Fe 415) in substructrue complete as per drawings and MoRD specification Clauses 1002, 1005, 1010 & 1202

Supply of Swiss type of Hazard marker, made out of 2 mm thick M.S. sheet size of box is 15x15 cm with hold fast at bottom, the body is painted in orange stoving enamel paint with white/high intensity grade micro-prismatic type sheeting, on all four side.

Painting Two Coats on New Concrete Surfaces Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and MoRD Specification Clause 1701

Supply of ‘L’ type Bollard made out of 1.25 mm thick M.S. sheet height 134 cm, welded in circular type ring section having upper dia 15 cm. and lower dia 21 cm with another attachment of 15x15 cm circular section with 15 cm. face plate and hold fast at bottom, whole body is processed in white stoving enamel and red reflective 3 hands, each of 7.5 cm endone reflective sheet of 15 cm. dia provided to it complete in all respec

Removal of existing sealant and re-sealing of contraction, longitudinal or expansion joints in concrete pavement with fresh sealant material hot poured rubberized bitumen or cold polysulphide type as per Clause 602.2.8 with appropriate type of primer complete as per MoRTH specification Clause 3005.2..

Demolishing CC/R.C.C. work by mechanical power driven means and stockpiling at designated locations and disposal ofdismentled material up to to lead of 50 m, stacking serviceableand unserviceable material seperately including cuttingreinforcement bars

Providing & fixing 3M radium tape of approved colour & Design complete in all respect as per instruction by Enginner in Charge

Supplying and fixing of micro prismatic retro reflective sheeting confirming to type XI of ASTM D4956, shall be pressure fixed to the full face of the ACP sheet as back ground sheet (in approved colour) and the top layer will be overlaid with electro cut transparent film of approved make and colour to create the desired road sign including cutting, cleaning and pasting etc. Complete as per design, drawing and direction of engineer in charge. (Payment shall be made for flat area of sheet), Make 3M/Avery Dennison or equivalent as approved by EIC, Confirming to type XI of ASTM D4956

Providing and fixing in position high bond (VHB) double tape 24mm wide 2.3mm thick for jointing ACP sheet with SS/MS frame including all processes like cleaning, cutting, chemical application, pressing etc. as per sample approved by the engineer-in-charge.

Painting over the existing poles above ground level including overhang making surface well clean and apply two coats of aluminium/ enamel paint as approved with required T & P etc as required. pole of 7 to 9 mtr long with one overhang

Painting over the existing poles above ground level includingoverhang making surface well clean and apply two coats ofaluminium/ enamel paint as approved with required T & P etcas required. pole of 7 to 9 mtr long with two overhang

Painting of existing traffic post /cantilever pole /signal head assembly/controller box including removing of old rusted surface paint and applying red oxide finishing two coats of enamel paint as requiredTraffic post

Painting of existing traffic post /cantilever pole /signal head assembly/controller box including removing of old rusted surface paint and applying red oxide finishing two coats of enamel paint as requiredTraffic post Cantilever pole

Milling the road surface in bituminous pavement including disposal of milled material with all lead and lift. Depth up to 50 mm

Milling the road surface in bituminous pavement including disposal of milled material with all lead and lift.Depth more than 50 mm and upto 100 mm

Providing and laying 25 mm thick bitumen mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29 (including cost of anti-stripping compound wherever required) @ 14-17% (by weight) as per job mix formula, coarse aggregate as per Table 500-32, fine aggregate as per Table 500-31 and lime stone powder as filler, prepared by using mastic cooker and laid to required level and grade after cleaning the surface, including providing antiskid surface with bitumen precoated fine-grained hard stone chipping of 13.2 mm nominal size @ 0.005cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces not less than 100 degree Centigrade, protruding 1 mm to 4 mm over mastic surface, all complete including all material, labour, machinery, lighting, guarding and maintenance of diversion complete as per clause 515 of MoRT&H specification

Tack Coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg persqm on the prepared dry and hungry bituminous surfacecleaned with Hydraulic broom as per MoRD Specification Clause503.0

Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the requiredgrade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRT & H Specifications Clause 509 complete in all respects for Grading-II (13 mm nominal size) Bitumen (VG-30)