Indira Gandhi Nahar Project Tender

P & F vitreous china P trap of approved quality.

P & F waste Coupling with fittings of approved quality /make:C.P. Brass 40 mm.

P & F European type white glazed vitreous china 1st quality Double syphonic W.C. (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor.

P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall :PVC with PVC bend as per IS : 7231.

P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make 32 mm waste pipe complete including cutting & making good the wall :Size 450 mm × 300 mm.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. (Internal work Exposed on wall) :15 mm nominal outer dia pipes.

Providing and fixing Superior quality CP Brass fittings of approved make complete as per direction of EI :Bib Cock with long thread 15 mm nominal size.

P & F Pillar Cocks (IS : 8934 Mark) of superior quality and approved make :C.P. Pillar cock, 15 mm dia nominal bore

P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. :C.P. Inlet connection 15 mm Brass (IS : 8931 marked).

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make :(-do-) Long body, 15 mm nominal bore weight not less than 690 gm.

Construction of chamber in all type of soil with 230/300 mm thick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20 mm thick insider plaster in CM 1:6, finished with floating neat cement, 50 mm thick M-15 grade C.C. flooring, earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Coupler 75 mm dia.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Double Tee with Door 75 mm dia.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Single Bend w/o Door 87.5° 75 mm dia.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes :Type A 75 mm diameter

040500 Supplying and fixing of power plug point accessories on 18 SWG metal box of size 175 x 100 x 60 mm. on surface or in recessed with suitable size phenolic laminated sheet cover including cost of 6 pin 16 amp. Switch and socket outlet , making connection , testing , etc. as required.040500.2 Group 1

040101 1 x 1.5 sq.mm040101.2 Group 1

020501 Short point (up to 3 mtr.)020501.2 Group 1

020701 On board020701.2 Group 1

Providing & Fixing of IP40 LED Surface/ Recessed / suspendedmounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency is greater than 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of is greater than equal to 120 lm/Watt ,THD is less than 10 % , p.f. is greater than equal to 0.95,CRI greater than 80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000 Degree K / 4000Degree K / 5700 Degree K /6000 Degree K/6500 Degree K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure A attacheded with this BSR. Recessed mounting 36 Watt LED light fixture 2 feet X 2 feet with acrylic / prismatic front cover CH E17 item E170911

12.5 Providing & Fixing of IP20 SMD Mid Power LED batten typeintegrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , Power Consumption of 18W/20W ,system lumen efficacy is greater than equal to 120 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD is less than 10% ,p.f. is greater than equal to 0.95, CRI is greater than 80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000 Degree K / 4000 Degree K / 5700 Degree K/6000 Degree K/6500 Degree K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure A attacheded with this BSR.4 12.5.1 LED Tube shape fixture 18/20 W (polycarbonate Base) CH E17 E170201

170900 P&F of Double ball bearing, capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible copper conductor ,making connections, testing etc. as required.170901 225 mm sweep170901.2 Group - 1

060121 6 A to 32 A rating060121.2 Group 1

Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200 mm × 300 mm in walls, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar)

Providing and fixing 1st quality MAT finished ceramic tile size 300×300 mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).

Distempering with 1st quality Acrylic washable distemper (ready mixed) of approved manufacturer and of required shade and colour complete including all scaffolding as per manufacturer s specification. Two or more coats on new work including preparation of base with primer, putty, lippy etc complete in all respect.

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. complete fine finish :20 mm thick.

Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete.

Brick work with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-inCharge. (Cost of aluminium snap beading shall be paid in basic item.) :With float glass panes of 5.0 mm thickness (weight not less than 13.50 kg/sqm.).

Providing and fixing aluminium work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap. at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling, C.P. brass / stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing and paneling to be paid for separately).For shutters builtup standard tubular sections of openable doors, windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately) : :Polyester Powder coating aluminium (minimum thickness of powder coating 50 micron).

Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin, of approved brand and manufacture in paneling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of Engineerin-Charge.Prelaminated particle board with decorative lamination on both sides.

Providing and fixing aluminium work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap. at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling, C.P. brass / stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing and paneling to be paid for separately).For fixed portion :Polyester Powder coating aluminium (minimum thickness of powder coating 50 micron).

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-inCharge :Polyester powder coated minimum thickness 50 micron aluminium

Providing and fixing 100 mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and Fixing hydraulic door closure ISI marked.

Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead :Of area 3 square meter and below.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead.