Medical Health And Family Welfare Department Tender

For 15 MM OD pipe

For 22 MM OD pipe

For 28 MM OD pipe

SITC of Gas outlet points (AR-4), (AR-7) and vacumm (8.7 psig) for dispensing medical gases (oxygen/air/vaccum) at point of use confirming to BSEN ISO 9170-1: 2008. The Gas outlet are quick connect for different gas source and should accept only respective adapters as required.

SITC of BPC (back pressure compensated) flow meter with humidifer made of nickel plated body double jacketed with flow gradations marked on it. Desired flow will be setteled through roatary knob. Flow range should be between 0 to 15 Ipm & work should be executed as per direction of engineer n charge.

SITC of suction unit (suction controller and collection jar) with posibility to configure required capacity capacity collection jar and should meets the requirements as per BSEN ISO 10079-3:2009 the unit must designed to operate with the vacucum regulator suitable for 0-14.7 psig with flow rate 0-55 Lmp (min) for operating temperature - 18'C to 50'C with ON/OFF facility. The collection jar should be transparent, made of high quality polycarbonate that can be autoclaved at 121'C for 20 minutes for reuse and provided with auto stop to avoid over spill and contamination of the suction source when the jar collection reached optimized level, the complete unit supplied with filter to protect the source and pipe line from bacterial contamination.

600 ml Capacity collection Jar

SITC of Valve box made of CRCA sheet duly powder coated with transparent window which is installed in the MGPS for sxygen and vaccum line and should comply with ENISO5211:2001 complete with ball type valves and gauses as required for oxygen compressed air and vaccum line (three gas)

For Three Gas

SITC of microprocessor based auto alarm system (digital type) suitable for medical gas service provided with audible and visual alarm for MGPS Zoning it should monitors the current status of oxygen/ compressed air pressure in distrubuton pipeline of central medical supply system and trigger the alarm to alert. The system should comply BSEN ISO:7396-1:2007

For Two Gas Services

SITC of Oxygen/Nitrous Oxide Manifold System (8,8)with tal pipes NRV-manifold system comprise of bank of 8+8 cylinders (Bulk cylinder of D type) capacity manifold high pressure copper pipe of size 1/2"ID x14 swg (approx 2.0320 mm) & high pressure fitting made of high tensile strength brass be used to connect the cylinders to the header assemblies with 16 no's non return valves & 16 no's high pressure flexible tail pipe is made of copper pipe of 1/3"x16 swg (approx. 1.6256 mm) the manifold is hydraulically tested at 225 kg/cm2 pressure it is also degreased and is to be offered duly wrapped in a polythene bag make CE Approved/CE. Note: Providing of Cylinders is in the scope of Hospital / End Client.

Wiring of 3 pin 5 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make on surface ISI marked ( IS:14927 P - II ) PVC casing capping & it's accessories, moulded PVC Modular box with earth terminal, 6 A modular switch, 6 A modular socket, Modular plate with grid plate, screws, making connections, testing etc. as required.

On Board

S&F following sizes of ISI marked ( IS:14927 P - II ) PVC casing capping along with accessories like coupler, inner, outer, elbow, square box, tee etc. on surface with screws, expansion fasteners as required.

25 mm x 12 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required.

2 x 2.5 sq. mm. + 1x1.5sqmm

P & F ISI marked 6 amp bakelite unbreakable 3 pin plug top including making connection testing etc. as required.

Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , Painting etc. as required.

SITC of automatic gas control panel for oxygen/nitrous oxide control panel cover made for M.S duly powder coated. Compact and fully automatic manifold control system for oxygen services easy to maintain and use Designed with both safety and continuity of flow supply at a constant pressure via two banks of bottled gas cylinders with following status monitoring A- Bank in use (Green Indication) B- Empty bank (Red Indication) Control Panel should have built in LED display to indicate Normal, High & Low line pressure. It should have facility to test all above indicators working perfectly. The control Panel should include pressure gauge to indicate the gas pressure of each header and pipe line distribution pressure. Capable to provide a distribution flow rate in excess of 1200 LPM. The control panel should incorporate manual bypass system in case of failure of shifting mechanism. It should be of CE certified product.