Dr Sarvepalli Radhakrishnan Rajasthan Ayurved University Tender

THAI-CHI SPINNER (2 WHEEL) :- Providing and fixing of THAI CHI SPINNER (2 wheel) of size not less than 700 mm (length) x 1000 mm (Width) x 1280 mm (Height) to increase mobility of shoulder, elbow and hip knee. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. High tensile S.S. nut hus shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

SEATED PULLER :- Providing and fixing of SEATED PULLER of size not less than 1900 mm (length) x 740 mm (Width) x 1920 mm (Height) to enhance the strength of upper limbs and the muscles in chest and back and promote cardiopulmonary function. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The handle frame shall be made from atleast 32 NB “C” class G.L. Pipe. The seat frame minimum of 32 NB “C” class G.I. pipe. cloasing caps shall be made up of high quality fiber reinforced plastic material. High tensile steel with galvanic Nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

LEG PRESS :- Providing and fixing of LEG PRESS of size not less than 1840 mm (length) x 360 mm (Width) x 1560 mm (Height) to build up the muscles of thigh and enhance the strength of waist. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The Sleeve frame minimum of 100 OD and of M.S. Seamless pipe with thickness 5 mm. This sleeve should be disassembled from main frame. The footrests shall be made from casted aluminum material, having sizes minimum of 130mm x 310 mm x 5 mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

SIT UP BOARD DOUBLE :- Providing and fixing of SIT UP BOARD DOUBLE of size not less than 1760 mm (length) x 1140 mm (Width) x 660 mm (Height) to enchance the flexibility of whole body. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The remaining frame of the sit up board minimum of 32 mm NB shall be made from ‘C’ class GI Pipe. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

CHEST PRESS :- Providing and fixing of CHEST PRESS of size not less than 2000 mm (length) x 710 mm (Width) x 2200 mm (Height) to enhance the strength of upper limbs and the muscles in chest and back and promote cardio pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The handle frame shall be made from atleast 32 NB “C” class G.O. Pipe. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. sheet of size not less than 300 mm x 300 mm x 2 mm thickness. Closing cap shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

POMMEL HORSE :- Providing and fixing of POMMEL HOUSE of size not less than 2150 mm (length) x 800 mm (Width) x 800 mm (Height) to enchance of lower limbs, waist and abdomen. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The handle frame be minimum of 32 NB shall be made from “C” class GI pipe. Closing caps shall be made up of high quality Fiber reinforced plastic Material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

DOUBLE STANDING TWISTER :- Providing and fixing of DOUBLE STANDING TWISTER of size not less than 1500 mm (length) x 600 mm (Width) x 1300 mm (Height) to enchance flexibility of waist. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The handle frame be minimum of 25 NB shall be made from “C” class GI pipe. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round plate of minimum size 0300 mm and 10 mm thick. Closing caps shall be made up of high quality Fiber reinforced plastic Material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

STANDING SEATING TWISTER :- Providing and fixing of STANDING SEATING TWISTER of size not less than 1700 mm (length) x 540 mm (Width) x 1250 mm (Height) to enhance flexibility of waist suitable for people of different ages except children. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thick. The bottom frame of the seating and standing twister be atleast of 25 NB shall be made from “C” class G.I. Pipe. The handle frame of seating and standing twister of minimum 25 NB and foot resting frame of seating side shall bemade from ‘C’ class G.I. Pipe minimum of 25 MM NB. The twister plate to be fitted on the bottom frame shall be made up of M.S. Round plate of minimum size 300 mm diameter and 10 mm thickness. Closing caps shall be made up of high quality fiber reinforced plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

CHEST CUM SHOULDER PRESS :- Providing and fixing of CHEST CUM SHOULDER PRESS of size not less than 2000 mm (length) x 710 mm (Width) x 2200 mm (Height) to enhance the strength of upper limbs and the muscles in chest and shoulder. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The handle frame shall be made from atleast 32 NB “C” class G.O. Pipe. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. sheet of size not less than 300 mm x 300 mm x 2 mm thickness. Closing cap shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

PUSH UP BARS :- Providing and fixing of PUSH UP BARS of size not less than 1220 mm (length) x 550 mm (Width) x 1700 mm (Height) to enchance the strength and stamina of the body. The main structure frame shall be made from G.I. pipe minimum of 80 NB ‘C’ class welded with M.S. round base plate atleast 250 mm &10 mm thickness. The handle frame be minimum of 25 NB shall be made from “C” class GI pipe. Closing caps shall be made up of high quality Fiber reinforced plastic Material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger / Nerolace Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer in charge to fulfill the functional requirement.

Items for Bal Vatika : FOR SEATER MRG :- Providing and fixing of For Seater MRG swing of size 4/5 feet (diameter), 3 feet (Height) fabricated with a Center Pipe/Frame of 50 NB shall be made from “C” Class G.I. pipe and FRP material. The bottom shall be welded with support of M.S. round plate of 250 mm &10 mm thickness. The bottom frame of 32 NB shall be made from “C” class G.I. pipe. The handle frame of 25 NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 50 NB ‘C” class welded with M.S. round plate of 250 mm & 10 mm thick. Main pipe shall be supported with 25 mm x 25 mm M.S. angle of 3 mm thickness and 20 mm x 40 mm CRC square pipes of 3 mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer in charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

Items for Bal Vatika : CIRCULAR SWING FOUR SEATER :- Providing and fixing of CIRCULAR SWING FOUR SEATER of size 6.0 x 5.25 x 5.0 Feet fabricated with a Center Pipe/ Frame of 65 NB shall be made from “C” Class G.I. pipe and FRP material. The bottom shall be welded with support of M.S. round plate of 250 mm &10 mm thickness. The bottom frame of 32 NB shall be made from “C” class G.I. pipe. The handle frame of 25 NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 65 NB ‘C” class welded with M.S. round plate of 250 mm & 10 mm thick. Main pipe shall be supported with 25 mm x 25 mm M.S. angle of 3 mm thickness and 20 mm x 40 mm CRC square pipes of 3 mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer in charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

Items for Bal Vatika : FOUR SEATER SEE SAW :- Providing and fixing of FOUR SEATER SEE SAW of size 5.5 x 6.25 x 2.5 Feet fabricated with a Center Pipe/ Frame of 50 NB shall be made from “C” Class G.I. material. The bottom shall be welded with support of M.S. round plate of 250 mm &10 mm thickness. The bottom frame of 32 NB shall be made from “C” class G.I. pipe. The handle frame of 25 NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 50 NB ‘C” class welded with M.S. round plate of 250 mm & 10 mm thick. Main pipe shall be supported with 25 mm x 25 mm M.S. angle of 3 mm thickness and 20 mm x 40 mm CRC square pipes of 3 mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer in charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

Items for Bal Vatika : HOURSE / DUCK / RABET SPRING RIDER :- Providing and fixing of HOURSE SPRING RIDER of size 3.0 x 2.5 Feet fabricated with a Center Pipe/ Frame of 40 NB shall be made from “C” Class G.I. material and FRP material. The bottom shall be welded with support of M.S. round plate of 250 mm &10 mm thickness. The bottom frame of 32 NB shall be made from “C” class G.I. pipe. The handle frame of 25 NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 40 NB ‘C” class welded with M.S. round plate of 250 mm & 10 mm thick. Main pipe shall be supported with 25 mm x 25 mm M.S. angle of 3 mm thickness and 20 mm x 40 mm CRC square pipes of 3 mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer in charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.