Department Of Local Bodies Tender

Providing and fixing testing and commissioning of kiosk type weather proof distribution feeder pillar box of sixe 600 x 450 x 1000mm with a taper of 75mm at top (for protection from rain water) and made out 3.2mm (10 gauge) thick locking arrangement by providing both side hold drafts and all hardware for fabrication of box. The cubical panel should be dust and vermin proof followed by two coats of enanel paint and primer. The cubical panel should be mounted with hardware on angle iron fram 40 x 40 x 6m and 600mm long legs duly primered and black painted. Frame be grouted with cement concrete 1:3:6 ratio in 150 X 150 X 750mm and providing brick masonry along angle iron frame above ground level. The panel should comprise of as per following : (a) P/F of 2 Nos. knife switch 400 amp. with U contacts studs and washers etc. (b) P/F 32 amp. Category-I make MCBs, 10 Nos. double pole & 5 nos TPN, (c) P&F of connecting strips of

Suitable for 15 kw load (three phase) including contactor, MCB, cable, glands, terminal block and locking arrangment each.

Supply and erection of octagonal pole of following length and dimension as per table-3 with base plate on the cement concrete foundation of M-15 /M-20 grade (1:1:5:3) with the help of anchor bolts, folded lengthwise to obtained octagonal shape, having single longitudinal seam weld and hot dipped galvanised internally & externally in accordance with IS 2629. The pole shall have a weatherproof flush door and locking arrangements. The complete work shall be supervised and certified by the manufacturers for satisfactory supply, erection, testing and commissioning 58.18.3 9 mtr. each 23220.00 18576.00

Plate Earthling as per IS:3043 with copper Earth plate of size 600mm x 600 mm x 3.0mm by embodying 3 to 4 mtr. Below the ground level with 25 mm dia. G.I. ‘B’ class watering Pipe including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I Frame of size 300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required.

Supply & Laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required 6 SWG copper wire metre.

Supply, Erection and Fixing of hot dipped galvanised Overhang (48.3 X 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. Single arm overhang each 1382.00

Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete.

P/F IP-65 / IP-66 protected street light luminaries on existing bracket. Fixture made from powder coated single piece pressure die cast aluminum housing with heat dissipation fins on housing with high power LEDs. Diffuser/glass cover for ensuring IP-65 protection for lamp and control gear compartment, system lumen output of 100 lum/watt high power LED. integrated driver shall be high effciency having efficiency more than 85% and in compliance to IEC standerds. system life of 50000 burning hours with 70% of initial lumens maintained. Fixture shall be in CE compliance.

P&F 240/415 V MCB of breaking capacity not less than 10 KA (B/C/D tripping characteristic) ISI marked IS 8828 (1996)/conforming to IEC 60898 in existing board/sheet including making connections with lugs, testing etc. as repuired. 40 A 63 A reating each

Providing and laying un-reinforced, dowel jointed, plain cement concrete mix in pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades complete as per drawing and as per clause 602, 112 of MoRT&H specification including all material, labour, machinery, lighting, guarding and maintenance of diversion.